Simplex 4100-1293 Installation Instructions Manual
Simplex 4100-1293 Installation Instructions Manual

Simplex 4100-1293 Installation Instructions Manual

Panel-mounted printer
Hide thumbs Also See for 4100-1293:

Advertisement

Quick Links

Cautions, Warnings, and Regulatory Information
READ AND SAVE THESE INSTRUCTIONS Follow the instructions in this installation manual. These instructions must be followed to avoid damage to
this product and associated equipment. Product operation and reliability depend upon proper installation.
DO NOT INSTALL ANY SIMPLEX™ PRODUCT THAT APPEARS DAMAGED Upon unpacking your Simplex product, inspect the contents
of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify an authorized Simplex
product supplier.
ELECTRICAL HAZARD Disconnect electrical field power when making any internal adjustments or repairs. All repairs should be
performed by a representative or an authorized agent of your local Simplex product supplier.
STATIC HAZARD Static electricity can damage components. Handle as follows:
• Ground yourself before opening or installing components.
• Prior to installation, keep components wrapped in anti-static material at all times.
EYE SAFETY HAZARD Under certain fiber optic application conditions, the optical output of this device may exceed eye safety limits. Do
not use magnification (such as a microscope or other focusing equipment) when viewing the output of this device.
Introduction
This publication describes the installation procedure for the 4100-1293 Panel-Mounted Printer.
The Panel-Mounted Printer
The 4100-1293 Panel-Mounted Printer (Figure 1) is used with the 4100/4100U/4100ES Fire Alarm System. The panel-mounted printer provides hard
copy reports of the master control panel's output and provides conformance with proprietary operation (formally known as NFPA 72D). The thermal,
dot matrix panel-mounted printer displays twenty visible lines of print, has a column width of forty characters, and is capable of printing variable
output formats on standard 2.350-inch wide thermal paper.
The panel-mounted printer does not require any changes to its default switch or jumper settings. It automatically detects the interface which is
sending data and produces the appropriate output. The serial interface parameters are factory-set and stored on the printer firmware. The standard
factory settings for the serial interface parameters are: 9600 baud, no parity, 8 data bits, and 1 stop bit.
4100-1293 Panel-Mounted Printer Installation Instructions
Figure 1: Panel-Mounted Printer, Front View
579-249 Rev. G
*0579249G*

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 4100-1293 and is the answer not in the manual?

Questions and answers

Summary of Contents for Simplex 4100-1293

  • Page 1 DO NOT INSTALL ANY SIMPLEX™ PRODUCT THAT APPEARS DAMAGED Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify an authorized Simplex product supplier.
  • Page 2 4100-1293 Panel-Mounted Printer Installation Instructions Unpacking and Inspection Before installing or operating the printer, check the following: Ensure that the primary power setting is correct for your installation. Ensure that the printer mechanism and paper path are clear of all packing materials or other foreign matter.
  • Page 3 4100-1293 Panel-Mounted Printer Installation Instructions Wiring Wiring consists of connecting the panel-mounted printer to RS-232 modules via pluggable connectors. This section describes the wiring process. The panel-mounted printer uses the harnesses listed in the figure below. Pressure-mounted supports are provided on the rear of the printer. Use a tie wrap to secure the harnesses to the support.
  • Page 4 4100-1293 Panel-Mounted Printer Installation Instructions Figure 4: Wiring the 4100-1293-Panel Mounted Printer Note: If Port A is used for the printer, place P2 jumper across pins 2-3 and P5 jumper across pins 1-2. If Port B is used for the printer, place P6 jumper on pins 1-2.
  • Page 5 Push the spring-loaded, rectangular latches inward and pull forward to release the printer access panel. Install a new roll of Simplex-approved paper (4190-9803 [473-019]) (thermal side up) on the upper spindle. Fold paper back onto itself to form a straight and clean edge and feed it directly into the paper input slot.
  • Page 6 © 2020 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision and are subject to change without notice. Additional listings may be applicable, contact your local Simplex® product supplier for the latest status. Listings and approvals under Simplex Time Recorder Co. Simplex, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited. NFPA 72 and National Fire Alarm Code are registered trademarks of the National Fire Protection Association (NFPA).

Table of Contents