Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Home Skinovations Silk'n FaceFX
Summary of Contents for Home Skinovations Silk'n FaceFX
- Page 1 Silk’n FaceFX ™ Face FaceFX ANTI-AGING INSTRUCTIONS FOR USE...
- Page 2 Fig. 1...
-
Page 3: Treating With Silk'n Facefx For The First Time
Treating with Silk’n FaceFX for the First Time The skin should be, clean, dry and free of any powder, gel or cream. If necessary a light serum may be applied thinly to the skin to help glide the device. Allow serum to absorb into the skin before treating. - Page 4 Silk’n FaceFX device description Silk’n FaceFX device consists of an APPLICATOR and an ADAPTOR. Silk’n FaceFX APPLICATOR is a hand held unit that contains a TREATMENT SURFACE at the APPLICATOR tip, an ON/OFF SWITCH and an INDICATOR PANEL. Treatment Surface On/Off Switch Indicator Panel APPLICATOR...
-
Page 5: Safety With Silk'n Facefx
Safety with Silk’n FaceFX To protect your skin, a temperature sensor is embedded in the treatment tip of the Silk’n FaceFX. This sensor ensures the skin’ s surface will not exceed 41°C / 106°F. When to avoid using Silk’n FaceFX? Certain conditions may temporarily prevent the use of Silk’n FaceFX. - Page 6 However every cosmetic procedure, including those designed for home use, involve some degree of risk. Therefore it is important that you understand and accept the risks and complications that can occur with energy based systems designed for home use. Silk’n FaceFX treatments are generally very well-tolerated. Most users sense the moderate heat applied by the device during use, with no further discomfort.
-
Page 7: Skin Treatment The Facefx Way
Skin Treatment the FaceFX Way The benefits of Silk’n FaceFX The outcome of using Silk’n FaceFX when following instructions correctly will be the reduction of facial fine lines, reducing pore size and improving the appearance of the face. Best results can be expected 3-7 weeks after completing the recommended course of treatment. Silk’n FaceFX facial treatment areas Typical areas for Silk’n FaceFX treatment are the cheeks, forehead, neck, and around the eyes. - Page 8 Treating with Silk’n FaceFX for the First Time The skin should be, clean, dry and free of any powder, gel or cream. If necessary a light serum may be applied thinly to the skin to help glide the device. Allow serum to absorb into the skin before treating. See “cleaning the Silk’n FaceFX” section. Remove Silk’n FaceFX APPLICATOR, ADAPTOR and other components from box.
-
Page 9: Maintenance Of Silk'n Facefx
Disconnect the FaceFX from the electrical outlet Disconnect the ADAPTOR PLUG from the FaceFX After each session it is recommended that you clean your FaceFX device, especially the APPLICATOR TIP (See Section: “Cleaning FaceFX”). Maintenance of Silk’n FaceFX Cleaning the Silk’n FaceFX After each session, it is recommended to clean your Silk’n FaceFX device: Turn Silk’n FaceFX off by pressing the POWER ON/OFF SWITCH. -
Page 10: Troubleshooting
Troubleshooting This chapter summarizes the most common problems you could encounter. If you are unable to solve the problem with the information below, contact your local Silk’n Customer Service Center for further support. Problem Possible Cause Solution Silk’n FaceFX does The Adaptor is not Connect the Plug (E) to the Applicator Plug not work... -
Page 11: Customer Service
1. For Israeli customers: For more information about Silk’n™ products please enter www.silkn.co.il. If your device is broken, damaged, in need of repair, or for any other user assistance, please contact Silk’n™ Customer Service: 1-700-700-309 contact@silkn.co.il Manufacturer: Home Skinovations Ltd. Tavor Building, Shaar Yokneam POB 533 Yokneam 2069206 Israel... -
Page 12: Specifications
Specifications Rated voltage (Adaptor) 100V - 240V Model: KSA24A1200150Hx Rated frequency (Adaptor) 50Hz/60Hz Rated adaptor 12Vdc; 1500 mA Applied part Type BF Protecting rating IP30 (EN60529) Storage condition Temperature: -40°C to 70°C /-40°F to 158°F Relative humidity: 10% - 90% Atmospheric pressure: 500 to 1060 hPa Classified standard IEC 60601-1-2:2007... - Page 13 Labeling Degree of protection against electric shock: type BF applied part WEEE - Waste Electrical and Electronic Equipment CSA Mark CE Mark Keep dry Manufacturer Degree of protection against ingress water: IP30 ordinary This device is not suitable for use in the presence of flammable anesthetic mixture with air or with Oxygen or Nitrous Oxide.
-
Page 14: Emc Testing Summary Results
EMC Testing Summary Results ... - Page 15 Skinovations Ltd. is believed to be accurate and reliable at the time of publication. However, Home Skinovations Ltd. assumes no responsibility for its use. No license is granted by its implication or otherwise under any patent or patent rights of Home Skinovations Ltd.
- Page 16 contact@silkn.co.il www.silkn.co.il...
Need help?
Do you have a question about the Silk'n FaceFX and is the answer not in the manual?
Questions and answers