Table of Contents
Advertisement
IDR-M Mimic Installation & Commissioning Manual
Address
Switch settings (1=on)
1
2
3
4
5
6
1
1
0
0
0
0
0
2
0
1
0
0
0
0
3
1
1
0
0
0
0
4
0
0
1
0
0
0
5
1
0
1
0
0
0
6
0
1
1
0
0
0
7
1
1
1
0
0
0
8
0
0
0
1
0
0
9
1
0
0
1
0
0
10
0
1
0
1
0
0
11
1
1
0
1
0
0
12
0
0
1
1
0
0
13
1
0
1
1
0
0
14
0
1
1
1
0
0
15
1
1
1
1
0
0
16
0
0
0
0
1
0
17
1
0
0
0
1
0
18
0
1
0
0
1
0
19
1
1
0
0
1
0
20
0
0
1
0
1
0
21
1
0
1
0
1
0
22
0
1
1
0
1
0
23
1
1
1
0
1
0
24
0
0
0
1
1
0
25
1
0
0
1
1
0
26
0
1
0
1
1
0
27
1
1
0
1
1
0
28
0
0
1
1
1
0
29
1
0
1
1
1
0
30
0
1
1
1
1
0
31
1
1
1
1
1
0
32
0
0
0
0
0
1
33
1
0
0
0
0
1
34
0
1
0
0
0
1
35
1
1
0
0
0
1
36
0
0
1
0
0
1
37
1
0
1
0
0
1
38
0
1
1
0
0
1
39
1
1
1
0
0
1
40
0
0
0
1
0
1
41
1
0
0
1
0
1
42
0
1
0
1
0
1
43
1
1
0
1
0
1
44
0
0
1
1
0
1
45
1
0
1
1
0
1
46
0
1
1
1
0
1
47
1
1
1
1
0
1
48
0
0
0
0
1
1
49
1
0
0
0
1
1
50
0
1
0
0
1
1
51
1
1
0
0
1
1
52
0
0
1
0
1
1
53
1
0
1
0
1
1
54
0
1
1
0
1
1
55
1
1
1
0
1
1
56
0
0
0
1
1
1
57
1
0
0
1
1
1
58
0
1
0
1
1
1
59
1
1
0
1
1
1
60
0
0
1
1
1
1
61
1
0
1
1
1
1
62
0
1
1
1
1
1
63
1
1
1
1
1
1
RS485 Termination Jumpers
If the IDR-M mimic is at either end of the
network, termination jumpers (B) JP2/4/6 -
TERM ON - on the Control board must be fitted
to put the line termination resistors in circuit. If
the IDR-M mimic is not at either end of the
network, these jumpers must not be fitted (the
link supplied on the Control board should be
placed across termination jumpers JP1/3/5 -
TERM OFF).
Note: If the Control PCB is removed from its
chassis, DO NOT forget to replace
screw (C) when re-fitting it.
Switch Configuration - RS232 Connection
Set the switches (located at position A):
a. Switches 1 to 6 set the IDR-M mimic
address, in the range 1 to 63 in binary (see
decode at left). Addresses above 63 can
be set by using the IDR Configuration Tool
(in this case the address switches must all
be set to 0). Address 0 is not valid for ID
b. Switch 7 must be set according to the type
of connection used by the mimic, in this
case 1 for ID
2
c. Set switch 8 according to the type of
network used by the fire panel, in this case
2
1 for an ID
net network.
13
2
net.
net via an RS232 link.
997-412-000-3, Issue 3
June 2005
Advertisement
Table of Contents
