Sealey SRS850 Manual

Sealey SRS850 Manual

Reciprocating saw 850w/230v

Advertisement

Quick Links

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. Safety
1.1.
eLectRicaL Safety
waRning! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey dealer.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
Do not pull or carry the appliance by the power cable.
8
Do not pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
Do not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Do not connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
geneRaL Safety
Stay alert, watch what you are doing and use common sense when operating a power tool.
9
Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
8
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes,
9
hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking
9
up or carrying the tool.
Remove any adjusting key or wrench before turning the power tool on.
9
Do not overreach. Keep proper footing and balance at all times.
8
Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. loose clothes, jewellery or long hair
8
can be caught in moving parts.
The use of a dust extraction system may reduce dust-related hazards.
9
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.
8
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer
8
at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is
8
dangerous and must be repaired.
Disconnect the plug from the power source and / or the battery pack, if detachable, from the power tool before making any
9
adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the
power tool accidentally.
Store idle power tools out of the reach of children and Do not allow persons unfamiliar with the power tool or these instructions to
9
operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories carefully. Check for misalignment or binding of moving parts, breakage of parts and any other
9
© Jack Sealey limited
RecipRocating Saw 850w/230V
Model no:
Wear protective
Wear safety
gloves
footwear
Original Language Version
SRS850
Wear protective
electrical shock
clothing
hazard
Hot surfaces
Wear a mask
Recommended fuse rating
13 Amp
SRS850 Issue 1 28/09/18

Advertisement

Table of Contents
loading

Summary of Contents for Sealey SRS850

  • Page 1 SRS850 Model no: thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 Immediately switch off the power tool if the insertion tool gets jammed. The power tool can lash out to the side. Wait until the power tool has come to a standstill, before putting it down. only use the device SRS850 for sawing plastic, wood, metal and building materials using the suitable saw blade. The device may be used for: •...
  • Page 3: Specification

    If you turn the handle, the saw blade can be inserted rotated by 180° (saw blade teeth point in the opposite direction) to enable easier working. fig.3 fig.4 fig.5 Original Language Version SRS850 Issue 1 28/09/18 © Jack Sealey limited...
  • Page 4: Rotating The Handle

    The LED work lamp (fig.1.12) will be illuminated. 5.3.8. After completing the sawing operation, let go of the on/off switch (fig.9.4) to stop the device. The LED work lamp (fig.1.12) will go out. Original Language Version SRS850 Issue 1 28/09/18 © Jack Sealey limited...
  • Page 5: Flush Cutting

    If required, allow the device to cool down. 5.10.4. Remove the tool from the tool holder (see Start-up chapter). 5.10.5. Clean the device according to the Maintenance chapter. fig.13 fig.14 Original Language Version SRS850 Issue 1 28/09/18 © Jack Sealey limited...
  • Page 6: Troubleshooting

    Check whether the chosen saw blade is suitable for the material to be processed. 6.7. tHe DeVice’S peRfoRMance DecReaSeS: 6.7.1. The carbon brushes may be worn and have to be replaced. Contact the Sealey customer service or an electrically skilled person. 6.8. tHe DeVice BecoMeS Hot: 6.8.1.
  • Page 7: Environment Protection

    Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey group, kempson way, Suffolk Business park, Bury St edmunds, Suffolk. ip32 7aR 01284 757500 01284 703534 sales@sealey.co.uk...
  • Page 8 waRning! – Risk of Hand arm Vibration injury. this tool may cause Hand arm Vibration Syndrome if its use is not managed adequately. This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC. This tool is to be operated in accordance with these instructions. Measured vibration emission value (a): ....

Table of Contents