Advertisement
Available languages
Available languages
3
Factory reset
Clear mode
4
Pairing with
Pairing mode
receiver
5-7
Not used
8
Tamper protection Disabled
Pairing with receiver
To pair the repeater with the receiver RCW-M32:
1. In Normal mode, slide DIP switch 4 to the ON position to put it into
Pairing mode. The repeater will emit 1 long beep and the yellow
LED will be lit.
2. Prepare the receiver for pairing according to the documentation for
RCW-M32.
3. Press the function button on the repeater. The repeater will transmit a
test code to the receiver as the red LED lights up and the repeater
emits 1 beep.
4. If the repeater receives an acknowledge signal from the receiver
within 60 s, the pairing is successful. The blue LED will light up for
1 second as the repeater emits 1 long beep.
If the repeater fails to receive an acknowledge signal from the
receiver within 60 s, the pairing has failed and is indicated by the
yellow LED flashing 3 times. Repeat the pairing procedure.
5. Slide DIP switch 4 to the OFF position. The repeater will emit 1
long beep and the yellow LED will turn off as the repeater returns
into Normal mode.
After being paired with the receiver, the repeater will automatically
transmit supervisory signals every 30-50 minutes. If the receiver has not
received the supervisory signal for a preset period of time it will set an
alarm in the Modbus register (Sensor Supervisor Error).
N N o o t t e e ! ! The receiver can use a maximum of 32 channels. Each connected
device, including the RPW, will use one channel in the receiver. Therefore,
the total number of repeaters or sensors and transmitters that can be
paired to the receiver is 32.
Pairing with repeater
To pair Repeater A with Repeater B:
1. In Normal mode, slide DIP switch 1 to the ON position on Repeater B
to put it into Pairing mode. Repeater B will emit 1 long beep and the
yellow LED will flash slowly (1 flash every 2 seconds).
2. Press the function button on Repeater A, it will emit 1 long beep and
Normal mode
the blue LED will light up for 1 second to indicate successful pairing.
Normal mode
If Repeater B receives the pairing signal from Repeater A, it will emit
1 long beep and the blue LED will light up for 1 second to indicate
successful pairing.
Normal mode
If Repeater B receives the pairing signal from Repeater A and Repeater
(enabled)
A was already paired, Repeater B will emit 2 beeps and the blue LED
will light up for 1 second.
3. When the pairing is complete, slide DIP switch 1 of Repeater B to the
OFF position. Repeater B will emit 1 long beep, the yellow LED will
turn off as Repeater B returns to normal mode.
N N o o t t e e ! ! Do not cross-pair the repeaters, i.e. do not pair Repeater A with
Repeater B as well as Repeater B with Repeater A.
All repeaters must also be paired with the receiver, RCW-M32.
Pairing with a sensor
To pair the repeater with a sensor (or transmitter):
1. In Normal mode, slide DIP switch 1 to the ON position to put it into
Pairing mode. The repeater will emit 1 long beep and the yellow
LED will flash slowly (1 flash every 2 seconds).
2. Send a pairing signal from the sensor according to its documentation
(usually a Test or Pair button is pressed on the sensor).
If the repeater receives a pairing signal from a new sensor, it will
emit 1 long beep and the blue LED will light up for 1 second to
indicate successful pairing.
If the repeater receives a pairing signal from a sensor that is already
paired with the repeater, it will emit 2 beeps and the blue LED will
light up for 1 second.
3. When the pairing is complete, slide DIP switch 1 to the OFF
position. The repeater will emit 1 long beep, the yellow LED will
turn off as the repeater returns to Normal mode.
N N o o t t e e ! ! If multiple repeaters are used, only pair sensors with the
repeater(s) closest to the operation areas of the sensors.
All the sensors that are paired with the repeater must also be paired with
the receiver.
Walk test
To put the repeater into Walk test mode to check for the signal range
with the sensors (or transmitters) or the receiver:
1. In Normal mode, slide DIP switch 2 to the ON position to put it into
Walk test mode. The repeater will emit 1 long beep and the yellow
LED will flash (1 flash every second).
2. When the repeater receives signals from the receiver or the paired
sensors, it will emit a long beep and the blue LED will light up for 1
second. The signal is then retransmitted as the red LED lights up for
1 second.
3. To exit walk test mode, slide DIP switch 2 to the OFF position. The
Factory reset
To clear the previously programmed memory and reset the repeater to
factory default:
1. In Normal mode, slide DIP switch 3 to the ON position. The repeater
2. Press and hold the function button for 5 seconds. The repeater will
3. To exit Clear Mode, slide DIP switch 3 to the OFF position. The
Tamper protection
The repeater has a tamper protection function which is enabled in
Normal mode. The tamper switch is in the normal operating position
when the repeater is hooked onto the wall mounting bracket. Tamper
violation happens when the repeater is removed from the hook and the
tamper switch is released. The tamper protection function can be
disabled by sliding DIP switch 8 to the ON position.
Handling
If the repeater receives a signal from the receiver (e.g. a command), the
signal is retransmitted to the corresponding sensor(s) from the repeater.
The transmission LEDs will light up accordingly.
If the repeater receives a signal from a sensor (e.g. an alarm signal), the
signal is retransmitted to the receiver from the repeater. The
transmission LEDs will light up accordingly.
Multiple repeaters
Figure 1 Receiver RCW-M32, repeaters A, B and C, with RF coverage, and sensor D
A transmission relay with multiple repeaters, see Figure 1, is formed the
following way:
1. Pair the repeater that is furthest away from the receiver to the
RPW
repeater will emit 1 long beep and the yellow LED will turn off.
will emit 1 long beep and the yellow LED will light up.
emit 1 long beep to indicate that all paired sensors and receivers are
cleared from the repeater.
repeater will emit 1 long beep and the yellow LED will turn off.
RCW-...
A
B
C
repeater(s) that is furthest away from the receiver in-between, i.e.:
– Repeater C must be paired to repeater B. Do not pair repeater B
to repeater C.
– Repeater B must be paired to repeater A. Do not pair repeater A
to repeater B.
– Repeater A must be paired to the receiver.
D
2 (11)
Advertisement
