Sealey SA2110/3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. ELECTRICAL SAFETY. p WARNING! It is the user’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and
all electrical connections for wear or damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products that are plugged
into an electrical supply not protected by an RCCB. If in doubt consult a professional electrician. You may obtain a Residual Current Device by
contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by
a qualified electrician, at least once a year, using a Portable Appliance Tester (PAT).
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances,
and the safety of appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply.
See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply leads and plugs for wear or damage and connections to ensure that none is loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supply
to be used, and check that plugs are fitted with the correct capacity fuse.
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired by a qualified electrician.
1.1.10. NOTE: THIS PRODUCT IS INTENDED FOR USE ON AN INDUSTRIAL 30AMP SUPPLY WHICH MUST BE INSTALLED BY A QUALIFIED
ELECTRICIAN. It may be possible to operate the compressor on a “Domestic” 13Amp outlet under the following conditions: The mains supply
must conform to IEE Wiring Regulations, and the “spur” used to run the compressor must not include any other socket which could be used for
another appliance. The distance of the socket from the mains distribution point must not exceed 5 metres.
An extension lead must not be used.
1.1.11. Note: Under certain conditions your compressor will draw more than 13Amps. Consequently,
we recommend a 30Amp supply and suggest that a direct round pin plug/socket is installed by
a qualified electrician. In the event that you choose to use a domestic 13Amp supply,
we provide the plug wiring instructions as follows:
(UK only - see diagram at right). Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the green/yellow earth wire to the earth terminal ‘E’.
b) Connect the brown live wire to the live terminal ‘L’.
c) Connect the blue neutral wire to the neutral terminal ‘N’.
Ensure the plug is fitted with a 13Amp fuse.
After wiring, check there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends past the cable restraint and that the cable restraint is tight.
NOTE: IF USED ON A DOMESTIC 13AMP SUPPLY AND THE FUSE REPEATEDLY BLOWS, CONTACT A QUALIFIED
ELECTRICIAN TO INSTALL A 30AMP SUPPLY.
1.2. GENERAL SAFETY INSTRUCTIONS
Familiarise yourself with the application and limitations of the compressor.
Ensure the compressor is in good order and condition before use. If in any doubt do not use the unit and contact an electrician/service agent.
p WARNING! Compressor must only be serviced by an authorised agent. DO NOT tamper with, or attempt to adjust, pressure switch or safety valve.
Before moving, or maintaining the compressor ensure it is unplugged from the mains supply and that the air tank pressure has been vented.
Only use recommended attachments and parts. To use non-recommended items may be dangerous and will invalidate your warranty.
Read the instructions regarding any accessory used with the compressor. Ensure the safe working pressure of any air appliance used exceeds
the compressors output pressure. If using a spray gun, check the area selected for spraying is provided with air change system/ventilation.
Ensure the air supply valve is turned off before disconnecting the air supply hose.
To move the compressor use the handle only. Lift the compressor so that the front leg gives enough clearance for manoeuvring but maintain
unit’s centre of gravity in front of the wheels. DO NOT attempt to lift or move the compressor by any means other than by handle.
Use the compressor in a well ventilated area and ensure it is placed on a firm surface.
Keep tools and other items away from the compressor when it is in use and keep area clean and clear of unnecessary items.
Ensure the air hose is not tangled, twisted or pinched.
Keep children and unauthorised persons away from the working area.
DO NOT dis-assemble compressor for any reason. The unit must be checked by qualified personnel only.
DO NOT use the compressor outdoors, or in damp, or wet, locations and DO NOT operate within the vicinity of flammable liquids, gases or solids.
DO NOT touch compressor cylinder, cylinder head or pipe from head to tank as these may be hot and will remain so for some time after shutdown.
DO NOT attempt to move the compressor by pulling the air tool hose. Only move the compressor by its handle.
DO NOT use this product to perform a task for which it has not been designed.
DO NOT deface the certification plate attached to the end of the compressor tank.
DO NOT cover the compressor or restrict air flow around the machine whilst operating.
INSTRUCTIONS FOR:
PREMIER LINE COMPRESSORS
SA2110/3, SA2115/3
Models:
& SA2120/3
Blue
Neutra
l
SA2110/3, SA2115/3 & SA2120/3 - 1069 - (2) - 150200
Yellow & Green
Earth wire
Brown
Live
wire
Cable
restrai