Page 1 Digital Camera User’s Guide Thank you for purchasing this CASIO product. • Before using it, be sure to read the precautions contained in this User’s Guide. • Keep the User’s Guide in a safe place for future reference. • For the most up-to-date information about this product, visit the official EXILIM Website at http://www.exilim.com/...
Page 2: Unpacking
Unpacking As you unpack your camera, check to make sure that all items shown below are included. If anything is missing, contact your original retailer. Digital camera * The shape of the power cord plug varies according to country or geographic area.
Page 3: Read This First
CASIO COMPUTER CO., LTD. is forbidden under copyright laws. • CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost profits suffered by you or any third party due to the use or malfunction of this product.
Page 4: Table Of Contents
What is a digital camera? ........13 What you can do with your CASIO camera ......14 First, charge the battery prior to use..
Page 5 Recording Movie Images and Audio To record a movie ..........53 Using Prerecord Movie .
Page 6 Controlling Color Saturation ......(Saturation) . . . 86 Adjusting Image Contrast ....... (Contrast) . . . 86 Specifying Flash Intensity .
Page 7 Using DPOF to Specify Images to be Printed and the Number of Copies ......... 117 Using the Camera with a Computer Things you can do using a computer...
Page 8 Appendix Precautions during Use ........150 Power Supply.
Page 9: General Guide
General Guide The numbers in parentheses indicate the pages where each item is explained. . Camera Front Shutter button (page 25) [ON/OFF] (Power) (page 22) [BS] button (page 58) Flash (page 40) Front lamp (pages 24, 42) Lens Microphone (pages 54, 107) Zoom button (pages 25, 50, 90, 91) Back lamp...
Page 10: Monitor Screen Contents
Charger Unit Monitor Screen Contents The monitor screen uses various indicators, icons, and values to keep you informed of the camera’s status. • The sample screens in this section are intended to show you the locations of all the indicators and figures that can appear on the monitor screen in various modes. They do not represent screens that actually appear on the camera.
Page 11: Movie Recording
. Shutter Button Half-pressed NOTE • If the current aperture, shutter speed, ISO sensitivity, or Auto Exposure is not correct, the setting will turn orange when you half-press the shutter button. . Movie Recording 1 2 3 Recording mode (page 25) Flash (page 40) ISO sensitivity (page 45) Aperture value...
Page 12: Movie Playback
. Snapshot Viewing blbk . Movie Playback File type Protect indicator (page 104) Folder name/file name (page 136) Snapshot image quality (page 82) Snapshot image size (page 36) ISO sensitivity (page 45) Aperture value Shutter speed Date/time (page 50) Metering mode (page 85) White balance setting (page 102) Flash (page 40) Recording mode...
Page 13: Quick Start Basics
Quick Start Basics What is a digital camera? A digital camera stores images on a memory card, so you can record and delete images a countless number of times. Record Delete Play You can use the images you record in a variety of different ways.
Page 14: What You Can Do With Your Casio Camera
What you can do with your CASIO camera Your CASIO camera is packed with a powerful selection of features and functions to make recording of digital images easier, including the following main functions. Tough, Shock resistant construction Applying the same technology developed for the G-SHOCK wristwatch, this camera has passed drop testing from a height of 2.13 meters/7 feet* for a level...
Page 15: Dynamic Photo
Dynamic Photo Extract a moving subject out of a series of Continuous Shutter images you have shot and insert them into another image to create a Dynamic Photo image that features the moving subject. Interval Recording This feature automatically records images at fixed intervals. You can fix the camera to a bicycle or automobile and have it shoot at regular intervals as you travel.
Page 16: First, Charge The Battery Prior To Use
Note that the battery of a newly purchased camera is not charged. Perform the steps under “To charge the battery” to bring the battery to a full charge. • Your camera requires a special CASIO rechargeable lithium ion battery (NP-80) for power. Never try to use any other type of battery.
Page 17: To Load The Battery
Other Charging Precautions • Use the special charger (BC-80L) to charge the special lithium ion battery (NP-80). Never use any other type of charger device. Attempting to use a different charger can result in unexpected accident. • A battery that is still warm due to normal use may not charge fully. Give the battery time to cool before charging it.
Page 18 Close the battery cover. Close the battery cover completely until it clicks securely in place. • For information about how to replace the battery, see page 158. Checking Remaining Battery Power As battery power is consumed, a battery indicator on the monitor screen indicates remaining power as shown below.
Page 19: Configuring Basic Settings The First Time You Turn On The Camera
Configuring Basic Settings the First Time You Turn On the Camera The first time you load a battery into the camera, a screen appears for configuring the display language, date, and time settings. Failure to set the date and time correctly will cause the wrong date and time data to be recorded with images.
Page 20: Preparing A Memory Card
If you make a mistake configuring display language, date, or time settings with the above procedure, refer to the following pages for information about how to correct the settings. – Display language: Page 144 – Date and time: Page 143 NOTE •...
Page 21: To Load A Memory Card
• Should water or any foreign object ever get into the card slot, immediately turn off the camera, remove the battery, and contact your retailer or nearest CASIO authorized service center. • Never remove the memory card from the camera while it is being accessed. Doing so can cause problems with proper file transfer, damage the memory card, etc.
Page 22: To Format (Initialize) A New Memory Card
To format (initialize) a new memory card You need to format a new memory card before using it for the first time. Turn on the camera and press [MENU]. Select the “Set Up” tab, select “Format” and then press [6]. Use [8] and [2] to select “Format”...
Page 23: Attaching A Protector
Attaching a Protector The camera comes with two protectors. Attaching one of the protectors helps to protect the side of the camera against damage if it is dropped. . About the screws that come with the camera The camera comes with a total of six screws: four long screws for attaching a protector, and two short screws.
Page 24: Holding The Camera Correctly
Holding the Camera Correctly Your images will not come out clearly if you move the camera when you press the shutter button. When pressing the shutter button, be sure to hold the camera as shown in the illustration below, and keep it still by pressing your arms firmly against your sides as you shoot.
Page 25: To Shoot A Snapshot
To shoot a snapshot Press [ON/OFF] (Power) to turn on the camera. Make sure R is on the display. If it isn’t, see page 58. Snapshot mode icon Remaining Snapshot Memory Capacity (page 173) Point the camera at the subject. You can zoom the image, if you want.
Page 26 Half-press the shutter button to focus the image. When focus is complete, the camera will beep, the back lamp will light green, and the focus frame will turn green. Half-press Press lightly until the button stops. Beep, beep (Image is in focus.) Continuing to keep the camera still, press the shutter button the rest of the way down.
Page 27: Using Quick Shutter
. Using Quick Shutter Fully pressing the shutting button without waiting for Auto Focus to operate will record using Quick Shutter (page 79). • With Quick Shutter, the camera focuses faster than normal Auto Focus, which means you can capture quick moving action more easily. Note, however, that some images may be out of focus when Quick Shutter is used.
Page 28: Viewing Snapshots
Viewing Snapshots Use the following procedure to view snapshots on the camera’s monitor screen. • For information about how to play back movies, see page 87. Press [p] (PLAY) to enter the PLAY mode. • This will display one of the snapshots currently stored in memory.
Page 29: Deleting Images
Deleting Images If memory becomes full, you can delete images you no longer need to free up storage and record more images. IMPORTANT! • Remember that a file (image) delete operation cannot be undone. • Deleting an audio snapshot (page 107) deletes both the snapshot and the audio file.
Page 30: Snapshot Shooting Precautions
Snapshot Shooting Precautions Operation • Never open the battery cover while the back lamp is flashing green. Doing so can result in the image you just shot being saved incorrectly, damage to other images stored in memory, malfunction of the camera, etc. •...
Page 31: Shock Resistant, Waterproof, Dustproof
Signifies underwater use when immersed for a duration and at a pressure specified by CASIO. Test conditions defined by CASIO. Does not include cases where battery life is shortened due to use conditions. IMPORTANT! • The shock resistance, waterproofing, and dustproofing of this product are based on CASIO test results, and do not constitute any guarantee that the product will perform, will not be damaged, or will not malfunction under such conditions.
Page 32 • This camera will sink if dropped underwater. Use the strap or some other means to avoid dropping. • The waterproofing of this camera protects it against salt water and fresh water only. Protection is not provided against hot spring water. •...
Page 33 • In order to maintain waterproofing, replacement of the camera’s gaskets is recommended once each year. Note that you will be charged for gasket replacement. Contact a CASIO authorized service center or your original retailer for gasket replacement. or greater) or °C...
Page 34 • CASIO COMPUTER CO., LTD. shall not be held liable for any accident that may occur while the camera is being used underwater. • CASIO COMPUTER CO., LTD. shall not be held liable for any damages or for any accident (personal injury, etc.) that occurs while using the camera underwater.
Page 35: Snapshot Tutorial
Snapshot Tutorial Using the Control Panel The Control Panel can be used to configure camera settings. In the REC mode, press [SET]. This will select one of the Control Panel icons and display its settings. [8] [2] [4] [6] [SET] Use [8] and [2] to select the setting you want to change.
Page 36: Specifying Control Panel Items
147). Changing the Image Size (Size) . Pixels A digital camera image is a collection of small dots called “pixels”. The more pixels there are in an image, the more detail there will be. However, you generally can do with fewer...
Page 37 . About image sizes The size of an image indicates how many pixels it contains, and is expressed as horizontal pixels vertical pixels. 8M (3264 2448) size image = Approximately 8 million pixels VGA (640 480) size image = Approximately 300,000 pixels Image Size Selection Tips Note that larger images have more pixels, so they take up more memory space.
Page 38: To Select The Snapshot Image Size
. To select the snapshot image size In the REC mode, press [SET]. Use [8] and [2] to select the top Control Panel option (Snapshot Image Size). Use [ ] and [6] to select an image size and then press [SET]. Suggested Image Size Print Size and...
Page 39 . Specifying Movie Image Quality Movie image quality is a standard that determines the detail, smoothness, and clarity of a movie during playback. Shooting with the high-quality (WIDE) setting will result in better image quality, but it also shortens the amount of time you can shoot. In the REC mode, press [SET].
Page 40: Using Flash
Using Flash (Flash) In the REC mode, press [2] ( Use [4] and [6] to select the flash setting you want and then press [SET]. Flash fires automatically in accordance with exposure Auto Flash > (amount of light and brightness) conditions. Flash Off Flash does not fire.
Page 41 NOTE • Take care so your fingers and the strap do not block the flash. • The desired effect may not be obtained when the subject is too far away or too close. • Flash charging time (page 176) depends on operating conditions (battery condition, ambient temperature, etc.).
Page 42: Using The Self-Timer
Using the Self-timer (Self-timer) With the Self-timer, pressing the shutter button starts a timer. The shutter is released and the image is shot after a fixed amount of time. In the REC mode, press [SET]. Use [8] and [2] to select the fourth Control Panel option from the top (Self-timer).
Page 43: Specifying The Auto Focus Area
Specifying the Auto Focus Area (AF Area) The camera automatically determines the focus point on the Intelligent screen and focuses there when the shutter button is half-pressed Ò (intelligent AF). This mode takes readings of a small area in the center of the Spot Û...
Page 44 “Ò Intelligent” Focus frame IMPORTANT! • “È Multi” cannot be selected for the Auto Focus area while you are using Face Detection (page 46). • “Ë Tracking” cannot be selected for the Auto Focus area while you are using Auto Shutter (page 73). •...
Page 45: Specifying Iso Sensitivity
Specifying ISO Sensitivity (ISO) ISO sensitivity is a measure of sensitivity to light. In the REC mode, press [SET]. Use [8] and [2] to select the sixth Control Panel option from the top (ISO Sensitivity). Use [4] and [6] to select the setting you want and then press [SET]. AUTO Adjusts sensitivity automatically according to conditions ISO 64...
Page 46: Shooting With The Rec Light
Shooting with the REC Light (REC Light) Selecting “On” causes the front lamp to turn on for illumination when shooting under low lighting conditions. In the REC mode, press [SET]. Use [8] and [2] to select the third Control Panel option from the bottom (REC Light).
Page 47 Point the camera at the subject(s). The camera will detect human faces and display a frame around each one. Half-press the shutter button. The camera will focus and the frames around the faces it focuses on will turn green. Press the shutter button the rest of the way down.
Page 48: Shooting With The Make-Up Mode
Shooting with the Make-up Mode (Make-up) The Make-up Mode smoothes the skin texture of the subject and softens facial shadows caused by harsh sunlight for better looking portraits. In the REC mode, use [4] and [6] to display in the control panel, which enters the ±...
Page 49: Shooting Beautiful Scenery Images
Shooting Beautiful Scenery Images (Landscape) The Landscape Mode makes colors more vivid, filters haze, and performs other processing that enhances the beauty of natural scenery. In the REC mode, use [4] and [6] to display in the control panel, which enters the Ö...
Page 50: Changing The Control Panel Date/Time Style
Changing the Control Panel Date/Time Style In the REC mode, press [SET]. Use [8] and [2] to select the bottom Control Panel option (Date/Time). Use [4] and [6] to select the date or time. NOTE • You can select either of two display style (page 143) for the date: Month/Day or Day/Month.
Page 51: Optical Zoom And Digital Zoom Switch Point
NOTE • The higher the digital zoom factor, the coarser the recorded image. Note that the camera also has a function that lets you record using digital zoom without image deterioration (page 52). • Use of a tripod is recommended to protect against image blur due to camera movement when shooting with telephoto.
Page 52 • The image deterioration point depends on the image size (page 36). The smaller the image size, the higher the zoom factor you can use before reaching the image deterioration point. • Though digital zoom generally causes a deterioration of image quality, some digital zoom without image deterioration is possible with image sizes of “8M”...
Page 53: Recording Movie Images And Audio
Recording Movie Images and Audio To record a movie Configure the quality setting for the movie (page 39). The length of the movie you can record will depend on the quality setting you select. In the REC mode, press [0] (Movie).
Page 54 NOTE • Spending a long time using movie recording will cause the camera to become slightly warm to the touch. This is normal and does not indicate malfunction. • The camera also records audio. Note the following points when shooting a movie. –...
Page 55: Using Prerecord Movie
Using Prerecord Movie With this feature, the camera prerecords up to four seconds of whatever is happening in front of the lens in a buffer that is continually updated. Pressing [0] saves the prerecorded action (buffer contents) followed by real-time recording. Real-time recording continues until you stop it.
Page 56: Shooting A Snapshot While Shooting A Movie
Shooting a Snapshot while Shooting a Movie While a movie is being recorded, press the shutter button. Movie recording continues after the snapshot is recorded. NOTE • You can use [2] ( ) while shooting a movie to change the flash mode setting. •...
Page 57: To Play Back An Audio Recording
NOTE • You can use [8] (DISP) during audio recording to toggle the monitor screen on and off. • When monitor screen contents are turned off, selecting the “Voice Recording” scene will cause the monitor screen to turn off immediately (page 148). About audio data •...
Page 58: Using Best Shot
Using BEST SHOT What is BEST SHOT? BEST SHOT provides you with a collection of sample “scenes” that show a variety of different types of shooting conditions. When you need to change the setup of the camera, simply find the scene that matches what you are trying to achieve, and the camera sets up for it automatically.
Page 59 Press [SET] to configure the camera with the settings for the currently selected scene. This returns to the REC mode. • The settings of the scene you selected remain in effect until you select a different scene. • To select a different BEST SHOT scene, repeat the above procedure from step 1.
Page 60 . BEST SHOT Precautions • The following BEST SHOT scenes cannot be used while recording a movie: Dynamic Photo, Multi-motion Image • The following BEST SHOT scene cannot be used while shooting a snapshot: Prerecord (Movie), For YouTube. • The Voice Recording scene cannot be used while shooting a snapshot or recording a movie.
Page 61: Creating Your Own Best Shot Setups
Creating Your Own BEST SHOT Setups You can save up to 999 camera setups as user BEST SHOT scenes for instant recall whenever you need them. On the BEST SHOT scene menu, select the scene named BEST SHOT (Register User Scene). Use [4] and [6] to select the snapshot or movie whose setup you want to save.
Page 62: Shooting With Auto Best Shot
Shooting with AUTO BEST SHOT With AUTO BEST SHOT, the camera automatically selects the BEST SHOT scene that suits your subject and shooting conditions, and configures its settings accordingly. The following are the scenes selected automatically by AUTO BEST SHOT. Portrait, Scenery, Night Scene, Night Scene Portrait, Macro, Sports, etc.
Page 63: Automatically Shooting At Regular Intervals
Automatically Shooting at Regular Intervals (Interval) You can configure the camera to repeatedly shoot snapshots or movies automatically at regular intervals. Press [BS] and then select the “Interval Snapshot” or “Interval Movie” scene. Press [SET]. Use [4] and [6] to select the “Interval” setting you want and then press [SET].
Page 64: Isolating Moving Subjects
IMPORTANT! • When the “Interval Movie” scene is selected, the shooting time setting is fixed at 5 seconds. • The sleep (page 144) and Auto Power Off (page 145) are disabled while an interval shooting operation is in progress. • Pressing any of the camera’s buttons while an interval shooting operation is in progress will cause the message “Interval shooting cancelled.”...
Page 65: Advanced Settings
Advanced Settings The following are menu operations you can use to configure various camera settings. • You also can use the Control Panel (page 35) to configure some of the settings that appear on the menu screen. Refer to the page references provided in this section for information about configuring settings using the Control Panel.
Page 66 Use [8] and [2] to select the menu item you want, and then press [6]. Use [8] and [2] to change the setting. After the setting is the way you want, press [SET]. • Pressing [ ] registers the selected setting and returns to the menu.
Page 67: Rec Mode Settings
REC Mode Settings (REC) Selecting a Focus Mode (Focus) Procedure REC mode * [MENU] * REC Tab * Focus Settings Type of Shot Q Auto General recording Focus ´ Macro Close ups Shooting with a E Pan relatively wide Focus focus range Scenery and other ) Infinity...
Page 68 Zoom Steps Z1 (Wide) Approx. 0.4 (1.3') Approx. 0.5 (1.6') Approx. 0.6 (2.0') Approx. 0.7 (2.3') Approx. 0.8 (2.6') Approx. 0.9 (3.0') Approx. 1.1 (3.6') Approx. 1.2 (3.9') Approx. 1.4 (4.6') Approx. 1.6 (5.2') Approx. 2.0 (6.6') Approx. 2.2 (7.2') 13 (Tele) Approx.
Page 69 To focus with manual focus On the monitor screen, compose the image so the subject you want to focus on is within the yellow boundary. Watching the image on the monitor screen use [4] and [6] to adjust focus. • At this time the image that is within the boundary will enlarge and fill the monitor screen, which aids in focusing.
Page 70: Using Continuous Shutter
Keeping the shutter button half-pressed (which maintains the focus setting), move the camera to compose the image. When you are ready to shoot the image, press the shutter button the rest of the way down. NOTE • Focus lock also locks exposure (AE). Using Continuous Shutter (CS) Procedure REC mode * [MENU] * REC Tab * CS...
Page 71: Specifying The Method For Saving Continuous Shutter Images
. Specifying the Method for Saving Continuous Shutter Images Specify the method to use for saving images recorded with “High Speed CS”. After continuous shutter shooting is finished, use [8] and [2] to select the save method you want and then press [SET]. Save Selected The shot images are played back at slow speed so you can select the images you want to save.
Page 72: Using The Self-Timer
IMPORTANT! • If there is not enough available capacity on the memory card, you may not be able to record the number of CS images indicated on the monitor screen. Make sure your memory card has sufficient remaining capacity before shooting with using continuous shutter.
Page 73: Shooting With The Rec Light
Shooting with the REC Light (REC Light) Procedure REC mode * [MENU] * REC Tab * REC Light For details, see the Control Panel procedure on page 46. Turning Movie Audio Recording On or Off (Movie Audio) Procedure REC mode * [MENU] * REC Tab * Movie Audio Selecting “On”...
Page 74 . To use Detect Blur to minimize image blur (Detect Blur) Point the camera at the subject and half-press the shutter button. Wait until the camera adjusts exposure and focus automatically. Press the shutter button the rest of the way down.
Page 75 . To use Detect Smile to record when a subject is smiling (Detect Smile) Point the camera at the subject and half-press the shutter button. Wait until the camera adjusts exposure and focus automatically. Press the shutter button the rest of the way down.
Page 76 Tips for Better Auto Shutter Snapshots • Using Auto Shutter in combination with Anti Shake (page 77) reduces the chance of image blur even more. • While recording with Detect Blur or Detect Smile, keep the camera as still as possible until the recording operation is complete.
Page 77: Shooting With Face Detection
Shooting with Face Detection (Face Detection) Procedure REC mode * [MENU] * REC Tab * Face Detection For details, see the Control Panel procedure on page 46. Reducing the Effects of Subject Movement (Anti Shake) Procedure REC mode * [MENU] * REC Tab * Anti Shake You can turn on the camera’s Anti Shake feature to reduce image blur due to subject movement when shooting a moving subject using telephoto, when shooting a fast- moving subject, or when shooting under dim lighting conditions.
Page 78: Using The Auto Focus Assist Light
Using the Auto Focus Assist Light (AF Assist Light) Procedure REC mode * [MENU] * REC Tab * AF Assist Light Half-pressing the shutter button while this setting is selected causes the front lamp to light, which provides illumination for focusing in areas where lighting is dim.
Page 79: Turning Digital Zoom On Or Off
Turning Digital Zoom On or Off (Digital Zoom) Procedure REC mode * [MENU] * REC Tab * Digital Zoom You can use this setting to turn digital zoom on or off. When digital zoom is turned off, operating the zoom button zooms the image with optical zoom only. Shooting with Quick Shutter (Quick Shutter) Procedure REC mode * [MENU] * REC Tab * Quick Shutter...
Page 80: Displaying The On-Screen Grid
Displaying the On-screen Grid (Grid) Procedure REC mode * [MENU] * REC Tab * Grid The on-screen grid can be displayed on the REC mode monitor screen for easy vertical and horizontal alignment when composing images. Turning on Image Review (Review) Procedure REC mode * [MENU] * REC Tab * Review While Review is turned on, the camera will display a image for about one second...
Page 81: Configuring Power On Default Settings
Configuring Power On Default Settings (Memory) Procedure REC mode * [MENU] * REC Tab * Memory When you turn off the camera, it remembers the current settings of all enabled memory items and restores them when you turn it back on. Any memory item that is disabled will be returned to its initial default setting whenever you turn off the camera.
Page 82: Image Quality Settings
Image Quality Settings (Quality) Specifying Snapshot Size (Size) Procedure REC mode * [MENU] * Quality Tab * Size For details, see the Control Panel procedure on page 38. Specifying Snapshot Image Quality (Quality (Snapshot)) Procedure REC mode * [MENU] * Quality Tab * T Quality Fine Gives image quality priority.
Page 83: Correcting Image Brightness
Correcting Image Brightness (EV Shift) Procedure REC mode * [MENU] * Quality Tab * EV Shift You can manually adjust an image’s exposure value (EV value) before shooting it. • Exposure Compensation Range: –2.0 EV to +2.0 EV • Unit: 1/3 EV Use [8] and [2] to adjust the exposure compensation value.
Page 84: Specifying Iso Sensitivity
Auto Configures the camera to adjust white balance automatically (Daylight) For shooting outdoors on a clear day ¤ (Overcast) For shooting outdoors on an overcast rainy day, in the shade, etc. (Shade) For shooting on a clear day in the shade of trees or buildings “...
Page 85: Specifying The Metering Mode
Specifying the Metering Mode (Metering) Procedure REC mode * [MENU] * Quality Tab * Metering The metering mode determines what part of the subject is metered for exposure. Multi-pattern metering divides the image into sections and measures the light in each section for a balanced exposure reading. Multi This type of metering provides error-free exposure settings for a wide range of shooting conditions.
Page 86: Using Built-In Color Filters
Using Built-in Color Filters (Color Filter) Procedure REC mode * [MENU] * Quality Tab * Color Filter Settings: Off, B/W, Sepia, Red, Green, Blue, Yellow, Pink, and Purple Controlling Image Sharpness (Sharpness) Procedure REC mode * [MENU] * Quality Tab * Sharpness You can specify one of five sharpness settings from +2 (sharpest) to –2 (least sharp).
Page 87: Viewing Snapshots And Movies
Viewing Snapshots and Movies Viewing Snapshots See page 28 for the procedure for viewing snapshots. Viewing a Movie Press [p] (PLAY) and then use [4] and [6] to display the movie you want to view. Press [SET] to start playback. Movie Playback Controls [4] [6] Fast forward/...
Page 88: Viewing Continuous Shutter Images
Viewing Continuous Shutter Images Each time you perform a continuous shutter (CS) operation, the camera creates a CS group that includes all of the images for that particular CS session. You can use the following procedure to play back the images in a particular CS group. Press [ ] (PLAY) and then use [ whose images you want to view.
Page 89: Deleting Continuous Shutter Images
NOTE • Multiple images shot using “Normal Speed CS” are stored individually and are not grouped. This means they can be displayed individually (page 28) but not as a CS group. Deleting Continuous Shutter Images You can use the following procedures to delete images while playback is in progress or paused.
Page 90: Zooming An On-Screen Image
Use [ ] and [ ] to display the CS group you want to divide up. Use [ ] and [ ] to select “Divide” and then press [SET]. • To divide up other CS group files, repeat steps 4 and 5. .
Page 91: Displaying The Image Menu
Displaying the Image Menu In the PLAY mode, press the zoom button w (]). Use [8], [2], [4] and [6] to move the selection boundary around the image menu. To view a particular image, use [8], [2], [4], or [6] to move the selection boundary to the image you want and then press [SET].
Page 92: Viewing Snapshots And Movies On A Tv Screen
Viewing Snapshots and Movies on a TV Screen Turn off the camera. Next, rotate the cover lock dial in the [ 4 OPEN] direction and open the memory card/terminal cover. Use the AV cable that comes with the camera to connect it to the TV. Making sure that the 4 mark on the camera is aligned with the 6 mark of the AV cable connector, connect the cable to the camera.
Page 93 Press [p] (PLAY) to turn on the camera. This will cause an image to appear on the TV screen, without anything appearing on the camera’s monitor screen. • You also can change the aspect ratio of the screen and the video output system (page 146).
Page 94: Other Playback Functions (Play)
Other Playback Functions (PLAY) This section explains menu items that you can use to configure settings and perform other playback operations. For information about menu operations, see page 65. Playing a Slideshow on the Camera (Slideshow) Procedure PLAY mode * [MENU] * PLAY Tab * Slideshow Start Starts the slideshow.
Page 95: Saving Music From Your Computer To Camera Memory
Effect Select the effect you want. Pattern 1 to 5: Plays background music and applies an image change effect. • Patterns 1 through 4 have different background music, but they all use the same image change effect. • Pattern 5 can be used for playback of snapshots only, and the “Interval” setting is ignored.
Page 96 Connect the camera to your computer (pages 122, 131). If you plan to save the music files to the camera’s memory card, make sure the card is loaded in the camera. Perform one of the following operations to open the memory card or built-in memory.
Page 97: Laying Out Snapshots With Layout Print
Laying Out Snapshots with Layout Print (Layout Print) Procedure PLAY mode * Spnapshot Screen * [MENU] * PLAY Tab * Layout Print You can use the following procedure to insert existing snapshots into the frames of a layout and produce a new image that contains multiple snapshots.
Page 98: Creating A Snapshot Of Movie Frames
Creating a Snapshot of Movie Frames (MOTION PRINT) Procedure PLAY mode * Movie Screen to be Used * [MENU] * PLAY Tab * MOTION PRINT Use [4] and [6] to scroll through the movie frames and display the one you want to use as the image of the MOTION PRINT image.
Page 99: Editing A Movie On The Camera
Editing a Movie on the Camera (Movie Editing) Procedure PLAY mode * Movie Screen of Movie to be Edited * [MENU] * PLAY Tab * Movie Editing The Movie Editing feature lets you use one of the following procedures to edit out a specific part of a movie.
Page 100 When the frame where you want the cut point to be is displayed, press [2]. (To-Point Cut) (Point-To-Point Cut) ¡ (From-Point Cut) Use [8] and [2] to select “Yes” and then press [SET]. The selected cut operation will take considerable time to complete. Don’t try to perform any camera operation until the “Busy...
Page 101: Optimizing Image Brightness
Optimizing Image Brightness (Lighting) Procedure PLAY mode * Snapshot Screen * [MENU] * PLAY Tab * Lighting You can use this setting to optimize the balance between bright areas and dark areas in existing images. Performs a higher level of brightness correction than the “+1” setting. Performs brightness correction.
Page 102: Adjusting White Balance
Adjusting White Balance (White Balance) Procedure PLAY mode * Snapshot Screen * [MENU] * PLAY Tab * White Balance You can use the white balance setting to select a light source type for a recorded image, which will affect the colors of the image. Daylight Outdoors, fair weather ¤...
Page 103: Adjusting The Brightness Of An Existing Snapshot
Adjusting the Brightness of an Existing Snapshot (Brightness) Procedure PLAY mode * Snapshot Screen * [MENU] * PLAY Tab * Brightness You can select one of five brightness levels, from +2 (brightest) to –2 (least bright). NOTE • The original snapshot is retained in memory and not deleted. •...
Page 104: Protecting A File Against Deletion
Protecting a File Against Deletion (Protect) Procedure PLAY mode * [MENU] * PLAY Tab * Protect Protects specific files. Use [4] and [6] to scroll through the files until the one you want to protect is displayed. Use [8] and [2] to select “On” and then press [SET].
Page 105: Editing The Date And Time Of An Image
Editing the Date and Time of an Image (Date/Time) Procedure PLAY mode * Snapshot Screen * [MENU] * PLAY Tab * Date/Time [8] [2] Changes the setting at the cursor location. [4] [6] Moves the cursor between settings. [BS] Toggles between 12-hour and 24-hour format. When the date and time settings are what you want, press [SET] to apply them.
Page 106: Resizing A Snapshot
Resizing a Snapshot (Resize) Procedure PLAY mode * Snapshot Screen * [MENU] * PLAY Tab * Resize You can reduce the size of a snapshot and save the result as a separate snapshot. The original snapshot is also retained. You can select resize an image to one of three image sizes: 8M, 5M, VGA.
Page 107: Adding Audio To A Snapshot
Adding Audio to a Snapshot (Dubbing) Procedure PLAY mode * Snapshot Screen * [MENU] * PLAY Tab * Dubbing You can add audio to a snapshot after you shoot it. You can re-record a snapshot’s audio whenever you want. You can record up to about 30 seconds of audio for a single snapshot.
Page 108: Copying Files
Voice Recording Playback Controls Fast forward/fast reverse Play/pause Volume adjustment Display content switching Stop playback • Audio of an Audio Snapshot also can be played back on a computer with Windows Media Player or QuickTime. Copying Files (Copy) Procedure PLAY mode * Snapshot Screen * [MENU] * PLAY Tab * Copy Files can be copied from the camera’s built-in memory to a memory card or from a memory card to built-in memory.
Page 109: Dynamic Photo
Dynamic Photo You can use the procedures in this section to crop either a moving subject or a still subject out of a snapshot and then insert it into another snapshot. Moving Subject To create a subject image to be inserted (Dynamic Photo) Press [BS] and then select the “Dynamic Photo”...
Page 110 Use [8] and [2] to select either “1” or “2” and then press [SET]. To shoot under these conditions: The subject against a complex background The subject against a plain (no pattern) background First, shoot an image that includes the subject you want to extract.
Page 111: Inserting A Subject Into A Background Image
Press the shutter button to shoot the background only. The camera compares the images you shot in steps 6 and 8 and extracts the subject. The extracted subject image will appear on the monitor screen. If you selected “Moving Subject”, the subject image will be moving on the display. •...
Page 112: To View A Dynamic Photo
Use [4] and [6] to select the subject image you want to insert and then press [SET]. Use the zoom button to adjust the size of the subject and use [8], [2], [4], and [6] to adjust its position. When everything is the way you want, press [SET]. This inserts the subject into the background image and creates a Dynamic Photo.
Page 113: Converting A Dynamic Photo To A Movie
Converting a Dynamic Photo to a Movie (Movie Converter) A Dynamic Photo (a background image plus subject) is stored as a series of 20 still images. You can use the following procedure to convert the 20 images that make up a Dynamic Photo to a movie.
Page 114: Printing
Printing Printing Snapshots Professional Print Service You can take a memory card that contains the images you want to print to a professional print service and have them printed. Printing on a Home Printer Printing Images on a Printer with Memory Card Slot You can use a printer equipped with a memory card slot to print images directly from a memory card.
Page 115: Connecting The Camera To A Printer
. Connecting the Camera to a Printer Turn off the camera. Next, rotate the cover lock dial in the [ 4 OPEN] direction and open the memory card/terminal cover. Use the USB cable that comes bundled with the camera to connect the camera to your printer’s USB port.
Page 116 . To print Turn on the printer and load paper. Turn on the camera. This will display the print menu screen. Use [8] and [2] to select “Paper Size”, and then press [6]. Use [8] and [2] to select a paper size and then press [SET].
Page 117: Using Dpof To Specify Images To Be Printed And The Number Of Copies
Using DPOF to Specify Images to be Printed and the Number of Copies . Digital Print Order Format (DPOF) DPOF is a standard that allows you to include image type, number of copy, and time stamp on/off information on the memory card with the images. After configuring settings, you can use the memory card to print on a home printer that supports DPOF or take the memory card to a professional print service.
Page 118 . Configuring the Same DPOF Settings for All the Images Procedure PLAY mode * Snapshot Screen * [MENU] * PLAY Tab * DPOF Printing * All images Use [8] and [2] to specify the number of copies. You can specify a value up to 99. Specify 00 if you do not want to print the image. •...
Page 119: Date Stamping
. Date Stamping You can use one of the following three methods to include the recording date in the printout of an image. Configuring camera settings Configure DPOF settings (page 117). You can turn date stamping on and off each time you print. You can configure settings so some images include the date stamp and some don’t.
Page 120: Using The Camera With A Computer
Using the Camera with a Computer Things you can do using a computer... You can perform the operations described below while the camera is connected to a computer. Save images to a computer and view them there Transfer images stored on your computer to camera memory Play back and edit...
Page 121: Using The Camera With A Windows Computer
Upload movie files to YouTube Transfer images to the camera View the User’s Guide YouTube Uploader for CASIO and Photo Transport will not run under 64-bit versions of Windows OS. Operating Install this software: System Version 7 / Vista / XP / Installation not required.
Page 122: Viewing And Storing Images On A Computer
. Computer System Requirements for Bundled Software Computer system requirements are different for each of the applications. See the “Read me” file that comes with each application for details. Information about computer system requirements also can be found under “Computer System Requirements for Bundled Software (Bundled CD-ROM)”...
Page 123 Use the USB cable that comes with the camera to connect it to your computer. • The camera does not draw power over the USB cable. Make sure the camera’s battery is sufficiently charged before connecting. • Make sure that you insert the cable connector into the USB/AV port until you feel it click securely into...
Page 124 Windows 7/Vista users: Click “Start” and then “Documents”. Windows XP users: Click “Start” and then “My Documents”. Windows 2000 users: Doubleclick “My Documents” to open it. • If you already have a “DCIM” folder in “Documents” (Windows 7/Vista) or “My Documents”...
Page 125: Playing Movies
Never use your computer to modify, delete, move, or rename any image files that are in the camera’s built-in memory or on its memory card. Doing so can cause problems with the camera’s image management data, which will make it impossible to play back images on the camera and can drastically alter remaining memory capacity.
Page 126: Uploading Movie Files To Youtube
Uploading Movie Files to YouTube Installing YouTube Uploader for CASIO from the CD-ROM that comes with your camera simplifies uploading of movie files you recorded with the “For YouTube” BEST SHOT scene to YouTube.
Page 127 . To upload a movie file to YouTube • Before you can use YouTube Uploader for CASIO, you need to go to the YouTube website (http://www.youtube.com/) and register as a user there. • Do not upload any video that is copyrighted (including neighboring copyrights) unless you yourself own the copyright or you have obtained the permission of the applicable copyright holder(s).
Page 128: Transferring Images From Your Computer To Camera Memory
. To transfer images to the camera Connect the camera to your computer (page 122). On your computer, click the following: Start * All Programs * CASIO * Photo Transport. This starts up Photo Transport. Drag the file(s) you want to transfer to the [Transfer] button.
Page 129 . To transfer computer screen captures to the camera Connect the camera to your computer (page 122). On your computer, click the following: Start * All Programs * CASIO * Photo Transport. This starts up Photo Transport. Display the screen whose screen capture you want to transfer.
Page 130: Viewing User Documentation
On the menu screen, click the “Language” down arrow button and then select the language you want. Click “Manual” to select it and then click “Digital Camera”. IMPORTANT! • You must have Adobe Reader or Adobe Acrobat Reader installed on your computer in order to view the contents of a PDF file.
Page 131: Using The Camera With A Macintosh
Using the Camera with a Macintosh Install the required software in accordance with what version of the Macintosh OS you are running and what you want to do. When you want to Operating do this: System Version Save images to your OS 9 Macintosh and view OS X...
Page 132 Use the USB cable that comes with the camera to connect it to your Macintosh. • The camera does not draw power over the USB cable. Make sure the camera’s battery is sufficiently charged before connecting. • Make sure that you insert the cable connector into the USB/AV port until you feel it click securely into...
Page 133: Transferring Images Automatically And Managing Them
On the camera, press [ON/OFF] (Power) to turn off the camera. After making sure that the green back lamp is unlit, disconnect the camera from the computer. . To view copied images Double-click the camera’s drive icon. Double-click the “DCIM” folder to open it. Double-click the folder that contains the images you want to view.
Page 134: Playing A Movie
Playing a Movie You can use QuickTime, which comes bundled with your operating system, to play back movies on a Macintosh. To play back a movie, first copy it to your Macintosh and then double-click the movie file. . Minimum Computer System Requirements for Movie Playback The minimum system requirements described below are necessary to play back movies recorded with this camera on a computer.
Page 135: Viewing User Documentation
Open the file named “camera_xx.pdf”. • “xx” is the language code (Example: camera_e.pdf is for English.). User Registration Internet registration only is supported. Visit the following CASIO website to register: http://world.casio.com/qv/register/ Using the Camera with a Computer...
Page 136: Files And Folders
Files and Folders The camera creates a file and saves it each time you shoot a snapshot, record a movie, or perform any other operation that stores data. Files are grouped by storing them in folders. Each file and folder has its own unique name. •...
Page 137: Memory Card Data
Memory Card Data The camera stores images you shoot in accordance with the Design Rule for Camera File System (DCF). . About DCF DCF is a standard that makes it possible to view and print images recorded on one manufacturer’s camera on DCF-compliant devices produced by other manufacturers. You can transfer DCF-compliant images recorded with another camera to this camera and view them on this camera’s monitor screen.
Page 138: Supported Image Files
. Supported Image Files • Image files shot with this camera • DCF-compliant image files This camera may not be able to display an image, even if it is DCF-compliant. When displaying an image recorded on another camera, it may take a long time for the image to appear on this camera’s monitor screen.
Page 139: Other Settings (Set Up)
Other Settings (Set Up) This section explains menu items that you can use to configure settings and perform other operations in both the REC mode and PLAY mode. For information about menu operations, see page 65. Adjusting Monitor Screen Brightness (Screen) Procedure [MENU] * Set Up Tab * Screen You can change the brightness of the monitor screen.
Page 140: Configuring Camera Sound Settings
Configuring Camera Sound Settings (Sounds) Procedure [MENU] * Set Up Tab * Sounds Startup Specifies the startup sound. Half Shutter Sound 1 - 5: Built-in sounds (1 through 5) Shutter Off: Sound off Operation Specifies the sound volume. This setting is also used as the Operation audio level during video output (page 92).
Page 141: Specifying The File Name Serial Number Generation Rule
Specifying the File Name Serial Number Generation Rule (File No.) Procedure [MENU] * Set Up Tab * File No. Use the following procedure to specify the rule that governs generation of the serial number used in file names (page 136). Tells the camera to remember the last used file number.
Page 142: Time Stamping Snapshots
Use [8], [2], [4], and [6] to select the geographic area you want and then press [SET]. Use [8] and [2] to select the city you want and then press [SET]. Press [SET]. IMPORTANT! • Before configuring World Time settings, make sure that the Home City setting is the place where you live or normally use the camera.
Page 143: Setting The Camera's Clock
Setting the Camera’s Clock (Adjust) Procedure [MENU] * Set Up Tab * Adjust [8] [2] Change the setting at the cursor location [4] [6] Move the cursor between settings [BS] Toggles between 12-hour and 24-hour format When the date and time settings are what you want, press [SET] to apply them. •...
Page 144: Specifying The Display Language
Specifying the Display Language (Language) Procedure [MENU] * Set Up Tab * Language . Specify the display language you want. Select the tab on the right. Select “Language”. Select the language you want. Configuring Sleep State Settings (Sleep) Procedure [MENU] * Set Up Tab * Sleep This feature turns off the monitor screen whenever no camera operation is performed for a preset amount of time.
Page 145: Configuring Auto Power Settings
Configuring Auto Power Settings (Auto Power Off) Procedure [MENU] * Set Up Tab * Auto Power Off Auto Power Off turns off the camera whenever no camera operation is performed for a preset amount of time. Trigger Time Settings: 1 min, 2 min, 5 min (The trigger time is always 5 minutes in the PLAY mode.) •...
Page 146: Configuring Usb Protocol Settings
Configuring USB Protocol Settings (USB) Procedure [MENU] * Set Up Tab * USB You can use the procedure below to select the USB communication protocol, which is used when exchanging data with a computer, printer, or other external device. Select this setting when connecting to a computer (pages 122, 131). Mass With this setting, the computer sees the camera as an external Storage...
Page 147: Formatting Built-In Memory Or A Memory Card
Formatting Built-in Memory or a Memory Card (Format) Procedure [MENU] * Set Up Tab * Format If a memory card is loaded in the camera, this operation will format the memory card. It will format built-in memory if no memory card is loaded. •...
Page 148: Configuring Monitor Screen Settings
Configuring Monitor Screen Settings You can turn display information on and off by pressing [8] (DISP). You can configure separate settings for the REC mode and PLAY mode. Information display on Information display + Histogram on Information display off Using the On-screen Histogram to Check Exposure Displays a histogram on the monitor screen which you can use to check the exposure of an image before you shoot it.
Page 149 Example Histograms A histogram towards the left side results when the overall image is dark. A histogram that is too far to the left may result in “black out” of the dark areas of an image. A histogram towards the right side results when the overall image is light.
Page 150: Appendix
Appendix Precautions during Use . Avoid Use While In Motion • Never use the camera to record or play back images while operating an automobile or other vehicle, or while walking. Looking at the monitor while in motion creates the risk of serious accident. .
Page 151 • Never try to take the camera apart or modify it in any way. Doing so creates the risk of electric shock, burn injury, and other personal injury. Be sure to leave all internal inspection, maintenance, and repair up to your dealer or nearest CASIO authorized service center.
Page 152 • The battery is intended for use with a CASIO Digital Camera only. Use with any other device creates the risk of the battery damage, or deterioration of battery performance and service life.
Page 153: Battery Life
• If battery charging does not end normally within the specified charging time, stop charging anyway and contact your local CASIO authorized service center. Continued charging creates the risk of battery overheating, fire, and explosion.
Page 154: Data Error Precautions
. Data Error Precautions Your digital camera is manufactured using precision digital components. Any of the following creates the risk of corruption of data in camera memory. – Removing the battery or memory card while the camera is performing some operation –...
Page 155: Caring For Your Camera
0 Should the power cord ever become damaged (to the point that internal wires are exposed or cut), immediately contact your original retailer or authorized CASIO authorized service center to request repair. Continued use of a damaged power cord creates the risk of fire, malfunction, and electric shock.
Page 156 Note that CASIO COMPUTER CO., LTD. shall not be held liable for use of this product in any way that infringes on the copyrights of others or that violates copyright laws.
Page 157: Power Supply
• Check if the charger and battery contacts are dirty. If contacts are dirty, wipe them clean with a dry cloth. If problems continue to occur after you perform the above steps, it could mean that the battery is faulty. Contact your nearest CASIO authorized service center. Appendix...
Page 158: To Replace The Battery
To replace the battery Before opening the battery cover, carefully wipe any sand or moisture from the camera to ensure that none of it gets inside the battery compartment. Open the battery cover and remove the current battery. With the monitor screen side of the camera facing upwards, slide the stopper in the direction indicated by the arrow in the illustration.
Page 159: Using The Camera In Another Country
. Storage Precautions • Storing the battery for a long time while it is charged can cause deterioration of battery characteristics. If you do not plan to use a battery for some time, fully use up its charge before storing it. •...
Page 160: Using A Memory Card
Using a Memory Card See page 20 for information about supported memory cards and how to load a memory card. To replace the memory card Before opening the memory card/terminal cover, carefully wipe any sand or moisture from the camera to ensure that none of it gets inside the camera.
Page 161 . Memory Card Handling Precautions Certain types of cards can slow down processing speeds. In particular, you may experience problems saving high-quality (WIDE and STD) movies. Use of certain types of memory cards increase the time it takes to record movies, which can cause movie frames to be lost.
Page 162: Computer System Requirements For Bundled Software
Hard Disk Drive Space : At least 180MB Other : Internet Explorer 6.0 or higher installed For details about the minimum system requirements for each software application, see the “Read me” files on the CASIO Digital Camera Software CD-ROM that comes bundled with the camera. Appendix...
Page 163: Reset Initial Default Settings
Reset Initial Default Settings The tables in this section show the initial default settings that are configured for menu items (displayed when you press [MENU]) after you reset the camera (page 147). Menu items depend on whether the camera is in the REC mode or PLAY mode. •...
Page 164 “Quality” Tab Size 12M (4000 Quality Normal (Snapshots) Quality » (Movies) EV Shift White Balance Auto Auto “Set Up” Tab Screen Auto 2 Startup: Sound 1 / Half Shutter: Sound 1 / Shutter: Sound 1 / Sounds Operation: Sound 1 / = Operation: ...//// / = Play: ...////...
Page 165: Play Mode
. PLAY Mode “PLAY” Tab Images: All images / Time: 30 min / Slideshow Interval: 3 sec / Effect: Pattern 1 Dynamic Photo – Movie – Converter Layout Print – MOTION PRINT 9 frames Movie Editing – Lighting – Red Eye –...
Page 166: When Things Don't Go Right
2)The battery may be dead. Charge the battery (page 16). If the battery goes dead soon after being charged, it means the battery has reached the end of its life and needs to be replaced. Purchase a separately available CASIO NP-80 rechargeable lithium ion battery. The camera 1)Auto Power Off may have activated (page 145).
Page 167 (page 40) or select a different BEST SHOT scene (page 58). The ? (Flash Off) The flash unit may be malfunctioning. Contact a CASIO icon flashes red on authorized service center or your original retailer. Note that...
Page 168 Problem Possible Cause and Recommended Action A recorded image 1)Camera power may have been turned off before the save was not saved. operation was complete, which will result in the image not being saved. If the battery indicator shows battery as soon as possible (page 18). 2)You may have removed the memory card from the camera before the save operation was complete, which will result in the image not being saved.
Page 169 Images are not This camera cannot display non-DCF images recorded onto a displayed. memory card using another digital camera. Images cannot be Note that you cannot edit the following types of snapshots. edited (with Layout • Snapshots created using MOTION PRINT Print, resizing, •...
Page 170 If the same message appears after you turn power back on, contact your retailer or a CASIO authorized service center. The time and date Load the camera’s battery and reconfigure the time and date settings configured settings (page 19).
Page 171: Display Messages
If the same LENS ERROR message appears after you turn power back on, contact a CASIO authorized service center or your original retailer. Load paper! The printer ran out of paper while printing. Memory is full with images you recorded and/or files saved Memory Full by editing operations.
Page 172 Shoot the image again. Your camera system is corrupted. Contact your retailer or an SYSTEM ERROR authorized CASIO authorized service center. There are no files. There are no files in built-in memory or on the memory card.
Page 173: Number Of Snapshots/Movie Recording Time/Voice Recording Time
Number of Snapshots/Movie Recording Time/ Voice Recording Time Snapshot Image Size Image (Pixels) Quality Fine (4000 3000) Normal Economy Fine (4000 2656) Normal Economy 16:9 Fine (4000 2240) Normal Economy Fine (3264 2448) Normal Economy Fine (2560 1920) Normal Economy Fine (2048 1536)
Page 174: Voice Recording
Movies (with audio recording) Image Maximum Quality File Size (Pixels) WIDE Maximum Movie Size: 4 GB Maximum YouTube Movie Length: 10 minutes Voice Recording Maximum File Format File Size 4 GB IMA-ADPCM Built-in memory capacity after formatting The above values are based on use of a microSD (SDHC) memory card (Panasonic Corporation).
Page 175: Specifications
Specifications File Format Snapshots: Movies: Audio (Voice Recording): WAV (monaural) Recording Media Built-in Memory (Image Storage Area: 35.7MB*) microSD/microSDHC * Built-in memory capacity after formatting Recorded Image Sizes Snapshot: Movies: Image Deletion 1 file; all files (with memory protection feature) Effective Pixels 12.10 Megapixels Imaging Element...
Page 176 Shutter Speed Snapshot (Auto): 1/2 to 1/1250 second Snapshot (Night Scene): 4 to 1/1250 second * May differ due to the camera setup. Aperture Value F3.9 (W) to F8.9 (W) (When used with ND filter) * Using optical zoom changes the aperture value. White Balance Auto, Daylight, Overcast, Shade, Day White Fluorescent, Daylight Fluorescent, Tungsten, Manual WB...
Page 177 Approximate Battery Life All of the values provided below represent the approximate amount of time under normal temperature (23°C (73°F)) before the camera turns off. These values are not guaranteed. Low temperatures shorten battery life. Number of Shots (CIPA) (Operating Time)* Continuous Playback (Snapshots)* Approximate continuous movie recording time Continuous Voice Recording*...
Page 178 135 g (4.8 oz) (excluding battery and memory card) * The shock resistance, waterproofing, and dustproofing of this product are based on CASIO test results, and do not constitute any guarantee that the product will perform, will not be damaged, or will not malfunction under such conditions.
Page 179 . Rechargeable lithium ion battery (NP-80) Rated Voltage Rated Capacitance Operating Temperature Requirements Dimensions Weight . Charger unit (BC-80L) Input Power Output Power Operating Temperature Requirements Supported Battery Type Charging Time Dimensions Weight • Power cord precautions for use in Singapore The power cord set is not supplied.
Page 180 CASIO COMPUTER CO.,LTD. 6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan MA1002-B...
Page 181 Dynamic Getting the Most Out of Dynamic Photo For a wealth of information about Dynamic Photo including explanations about how to use Dynamic Photo images, the Dynamic Studio image conversion service, sample images, and more, visit the special Dynamic Photo website at: This manual provides an introduction to Dynamic Photo, which creates a whole new way to enjoy digital imaging.
Page 182: Dynamic Photo! A Totally New Way To Enjoy Digital Photography
Dynamic Photo! A totally new way to enjoy digital Dynamic Photo makes it easy to crop a moving subject out of a series of images and insert it into other images! A simple operation on the camera extracts a moving subject automatically by cropping up to 20 Continuous Shutter images.
Page 183: Using The Dynamic Photo Extracted Sample Subjects
Using the Dynamic Photo Extracted Sample Subjects Your digital camera comes with a number of extracted sample subjects in its built-in memory. You can use these sample subjects to practice creating Dynamic Photo images by inserting them into your original snapshots.
Page 184 After creation of the Dynamic Photo image is complete, the finished image with the inserted moving subject will appear on the monitor screen. After you master the above procedure using extracted sample subjects, you will be ready to create your own extracted subjects and insert them into snapshots for totally original Dynamic Photo images.
Page 185: Creating A Dynamic Photo Image
Creating a Dynamic Photo Image Step 1: Shoot the subject. Dynamic Photo images are created by extracting the subject out of one image, and inserting it into another image. The term “subject” as used here refers to what you extract or crop out of the first image. Perform the following steps to shoot and extract the subject.
Page 186 First, shoot the subject. Best results can be obtained with the camera secured on a tripod. With the camera pointed at the moving subject, press the shutter button to record. If you selected “Moving Subject”, the camera will record a series of Continuous Shutter (CS) images over a few seconds.
Page 187: Step 2: Create The Dynamic Photo Image
Complete! The camera compares the images you shot in steps 3 and 4 and extracts the subject. The extracted subject image will appear on the monitor screen. If you selected “Moving Subject”, the 20 subject images that were recorded will scroll on the screen, creating the illusion of movement.
Page 188 Use [4] and [6] to select the subject you want to insert and then press [SET]. * Only subjects that can be inserted into other images will appear at this time. Use the zoom button to adjust the size of the subject and use [8], [2], [4], and [6] to adjust its position.
Page 189: Four Tips For Good Subject Cropping
Four Tips for Good Subject Cropping • When shooting the subject image, shoot against a white wall or some other surface whose color is different from that of the subject. The camera will not be able to crop the subject image properly if its color is the same as or similar to the background color.
Page 190: Specifying The Subject Type And Cs Speed
Move the subject away from the wall to avoid shadows! The camera may mistake shadows on the wall or floor caused by strong sunlight, illumination, or other light sources as part of the subject. Shadows tend to form when the subject is too close to a wall.
Page 191: Changing The "Number Of Shots" Setting
CS speed Moving Subject 20 frames per 1sec (20fps) second Moving Subject 10 frames per 2sec (10fps) second Moving Subject 5 frames per 4sec (5fps) second Still Subject Changing the “Number of Shots” Setting Normally you need to shoot the subject you want to extract against a background and then shoot the background again without the subject.
Page 192: Step 3: Have Fun With Dynamic Photo
Step 3: Have fun with Dynamic Photo. You can use the Dynamic Photo image you created in Step 2 in a variety of fun ways. Step 4: Convert a Dynamic Photo to a Movie A Dynamic Photo is stored as a series of 20 still images. You can use the following procedure to convert the 20 images that make up a Dynamic Photo to a movie.
Page 193: Step 5: Use Dynamic Studio To Expand Use Of Dynamic Photo Images To Other Applications
This makes it possible to view Dynamic Photo images you created with a CASIO EXILIM digital camera to a format that can be played back as a movie on a PC, digital photo frame, cell phone or other device.

This manual is also suitable for:

Exilim g ex-g1

Casio EXILIM G MA0910-A 1170 User Manual

Table of Contents

Quick Start Basics

Snapshot Tutorial

Recording Movie Images and Audio

Using BEST SHOT

Advanced Settings

Viewing Snapshots and Movies

Other Playback Functions (PLAY)

Dynamic Photo

Printing

Using the Camera with a Computer

Other Settings (Set Up)

Configuring Monitor Screen Settings

Appendix

Dynamic Photo

Dynamic Photo! a Totally New Way to Enjoy Digital Photography

Using the Dynamic Photo Extracted Sample Subjects

Creating a Dynamic Photo Image

Quick Links

Chapters

Related Manuals for Casio EXILIM G MA0910-A 1170

Summary of Contents for Casio EXILIM G MA0910-A 1170