Download Print this page
Juniper MWS1000 Hardware Manual
Juniper MWS1000 Hardware Manual

Juniper MWS1000 Hardware Manual

Mykonos web security 4.95.8

Advertisement

Quick Links

Mykonos Web Security 4.95.8
Hardware Guide

Advertisement

loading
Need help?

Need help?

Do you have a question about the MWS1000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Juniper MWS1000

  • Page 1 Mykonos Web Security 4.95.8 Hardware Guide...
  • Page 2 Mykonos Web Security 4.95.8 Hardware Guide This document contains a specification for the MWS1000 hardware appliance, as well as instructions for installation into a server environment.
  • Page 3 1.1. Chassis Overview for MWS1000 ....................1 1.2. Front Panel Features for MWS1000 ..................1 2. Site Preparation 2.1. Clearance Requirements for Airflow and Hardware Maintenance for MWS1000 ......3 2.2. Power Specifications ........................ 3 2.3. Unpacking and Inspecting the MWS1000 .................. 4 2.4.
  • Page 4 -48 VDC, 20 A Max, 650 W. 1.2. Front Panel Features for MWS1000 This shows the front panel features of MWS1000. The MWS1000 Front Panel LEDs are listed below. 1. Power (green) - Appliance is powered on. 2. Hard disk activity (yellow) - Storage drive is in use.
  • Page 5 MWS1000 Rear Panel provides access to the removable fans and power supplies. The MWS1000 measures 1.75 high by 17.25 wide by 28 inches deep (44.5 x 438 x 710 mm). It weighs approximately 31 lbs (14 kg), depending on configuration.
  • Page 6: Site Preparation

    The MWS1000 environmental requirements are: • Ambient temperature for normal operation: 41°F to 104°F (5°C to 40°C) •...
  • Page 7 • Contact the shipper responsible for delivery, and formally report the damage. • Contact Juniper Networks at 1-888-314-JTAC (from the United States, Canada, or Mexico) or 1-408-745-9500 (from elsewhere), or contact your sales representative or reseller if you have any questions or concerns.
  • Page 8 Before You Install MWS1000 • For DC-power-equipped appliances, you must provide an external certified, dedicated circuit breaker rated at a minimum of 20 A for each DC power supply. • For DC-power-equipped appliances, you must supply four DC power cables that meet your local code requirements.
  • Page 9 10. Power on the appliance. When you turn on the power, the internal port uses its two LEDs to indicate the LAN connection status. 3.1. Connecting Power to AC-Powered MWS1000 The power supply in a Virtual Services Engine is located on the rear panel. To connect AC power to the appliance, plug both cords in and then turn the power on.
  • Page 10 Connecting Power to DC-Powered MWS1000 Connect DC power to the appliance by attaching power cables from the external DC power sources to the terminals on the power supply faceplates. You must provide the power cables. To connect the DC source power cables to a DC power supply on the appliance: 1.
  • Page 11: Rj-45 Console Connector Pinout

    RJ-45 Console Connector Pinout 8. Switch on the dedicated customer site circuit breaker for the power supply. 3.3. RJ-45 Console Connector Pinout Table 3.1. RJ-45 Console Connector Pinout reference Description RTS Output - Request to Send DTR Output - Data Terminal Ready TxD Output - Transmit Data GND - Chassis Ground GND - Chassis Ground...