Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for honor Band 6
Summary of Contents for honor Band 6
- Page 1 HONOR Band 6 User Guide...
-
Page 2: Table Of Contents
Contents Getting started Powering on, powering off, and restarting Pairing and connecting Charging your band Buttons and gestures Changing watch faces Notifications Setting alarms Receiving weather reports Incoming calls Workout modes Starting an individual workout Viewing workout records Viewing daily activity data Automatic workout detection Health management Sleep tracking... - Page 3 Contents Turning the screen on and off Restoring the band to its factory settings Updating your band Viewing the Bluetooth name, MAC address, serial number, model, and version number Water resistance...
-
Page 4: Getting Started
Getting started Powering on, powering off, and restarting Powering on the band Press and hold the button to power on the band. • The band will power on automatically when you connect it to a charger. • You will be prompted with a message asking you to charge your band when the battery is critically low. -
Page 5: Charging Your Band
Use the dedicated charging cable, charging cradle, rated output voltage of 5 V, and rated output • current of 1 A or USB power output to charge your band. Charging the band using a non-Honor charger or a power bank may result in it taking a longer time to charge, the band being unable to... -
Page 6: Buttons And Gestures
Getting started Charging time It takes around 65 minutes to fully charge the band. Viewing the battery level To view the battery level, swipe down on the band's home screen or open Health, then go to Devices and check under the connected device's name. Low battery alert When the battery level is lower than 10%, your band will vibrate to remind you. -
Page 7: Changing Watch Faces
This feature is only available in some countries and regions. For more information, contact the • official Honor service hotline. Notifications Once the notifications feature is enabled, the band can sync notifications displayed in the phone's notification panel to your band. -
Page 8: Setting Alarms
Getting started Your band will receive notifications but will not notify you during workouts, Do Not Disturb mode, • Low battery alert, Sleep mode or not wearing the band. Swipe up on the home screen to view new messages. You will not receive any app notifications on your wearable device if the chat is also open on your •... -
Page 9: Receiving Weather Reports
Getting started Event alarms are synced between the band and Health app. • There is only one smart alarm by default. You cannot add more or delete the smart alarm. You can • set a maximum of five event alarms. The smart alarm may vibrate in advance if it detects that you woke up before the alarm is set to go •... - Page 10 Getting started You can reject calls directly on your band. • If you aren't wearing the band, it will not light up its screen to notify you when there is an • incoming call. If the call is missed, the band will vibrate and the screen will turn on to notify you of the missed •...
-
Page 11: Workout Modes
Magic UI 2.0 or later, or iOS 9.0 or later. If all these conditions are met, your band can record your workout once the workout starts. Outdoor cycle is supported on Honor phones running Magic UI 2.0 or later and iPhones that run •... -
Page 12: Viewing Workout Records
Workout modes Viewing workout records Viewing workout records on the band On your band, enter the app list and touch Workout records. Then select a record to view the details. Your band will display different data types for different workouts. •... -
Page 13: Automatic Workout Detection
Workout modes Automatic workout detection Your band can identify your workout status on its own. This feature is disabled by default. To use it, you need to enable it manually. After you have enabled Auto-detect workouts under Settings > Workout settings, the wearable will remind you to start the workout if it detects that there is a change in your activity intensity and suggests a workout mode for you. -
Page 14: Health Management
Health management Sleep tracking Your band collects sleep data and identifies your sleep status when you wear it while sleeping. It can automatically detect when you fall asleep and wake up and whether you are in a light or deep sleep. Your sleep data for a single day is measured from 8:00 PM the night before to 8:00 PM of that day for a total of 24 hours. -
Page 15: Monitoring Your Heart Rate
Health management This feature is only available in some countries and regions. For more information, contact the • official Honor service hotline. The reading will be interrupted if you swipe right on the band screen, receive an incoming call, or •... - Page 16 Health management Resting heart rate measurement Resting heart rate refers to your measured heart rate when you are awake and at rest. The best time to measure your resting heart rate is immediately after you wake up in the morning. Open Health, touch Devices then your device name, go to Health monitoring >...
-
Page 17: Heart Rate Alerts
Health management After completing your workout, you can check your average heart rate, maximum heart rate, and • heart rate zone on the workout results screen. Your heart rate will not be displayed if you remove the band from your wrist during the workout. •... -
Page 18: Low Heart Rate Alert
Health management Low heart rate alert If you haven't been resting or sleeping for the past 10 minutes and your heart rate stays below the limit for 10 consecutive minutes, your band will vibrate once and display a message letting you know that your heart rate is too low. -
Page 19: Menstrual Cycle Predictions
• This feature is only available in some countries and regions. For more information, contact the • official Honor service hotline. Touch Records to view and modify period data. The predicted period is marked in the dotted line. • Your wearable device will remind you about the start of your period before 8 AM on the day before •... -
Page 20: Handy Features
If the number calls again, the new tag will be displayed along with their phone number on your phone and band. Requires a Honor phone running Magic UI 2.0 or later. Stopwatch On the band, enter the app list, swipe on the screen, and touch Stopwatch. -
Page 21: Flashlight
Handy features Touch to start the timer, touch to pause the timer, or touch to exit the timer. Swipe right on the screen or press the button to move Timer to the background. • The band will vibrate to inform you when the time is up. •... -
Page 22: More Guides
More guides Do Not Disturb mode Swipe on the band screen to display the menu, touch to enable Do Not Disturb. Alternatively, enter the app list, go to Settings > Do Not Disturb, and schedule a period for this mode. After Do Not Disturb is enabled: The band will not vibrate to notify you of incoming calls or notifications, and the Raise to wake •... -
Page 23: Restoring The Band To Its Factory Settings
More guides To set the screen sleep time, on your band, go to Settings > Display > Advanced and set the sleep time to 10 sec, 15 sec, 20 sec, or Auto. If Sleep is set to Auto, the band screen will turn off when you tilt or lower your wrist. -
Page 24: Water Resistance
More guides Press the button and go to Settings > About to view the MAC address of the device. Viewing the SN: Press the button and, go to Settings > About. The name displayed under SN is the serial number of the device. Viewing the model: Press the button and go to Settings >...
Need help?
Do you have a question about the Band 6 and is the answer not in the manual?
Questions and answers