Subscribe to Our Youtube Channel
Related Manuals for honor Band 6
Summary of Contents for honor Band 6
-
Page 1: Table Of Contents
Contents Getting started Powering on, powering off, and restarting Pairing and connecting Charging your band Buttons and gestures Changing watch faces Notifications Setting alarms Receiving weather reports Incoming calls Workout modes Starting an individual workout Viewing workout records Viewing daily activity data Automatic workout detection Health management Sleep tracking... - Page 2 Contents Adding favorites Turning the screen on and off Restoring the band to its factory settings Updating your band Viewing the Bluetooth name, MAC address, serial number, model, and version number Water and dust resistance...
-
Page 3: Getting Started
Getting started Powering on, powering off, and restarting Powering on the band Press and hold the button to power on the band. • The band will power on automatically when you connect it to a charger. • You will be prompted with a message asking you to charge your band when the battery is critically low. -
Page 4: Charging Your Band
1 A or USB power output to charge your band. Charging the band using a non-Honor charger or a power bank may result in it taking a longer time to charge, the band being unable to charge fully, overheating, or other similar issues. -
Page 5: Buttons And Gestures
Getting started Viewing the battery level To view the battery level, swipe down on the band's home screen or open Health, then go to Devices and check under the connected device's name. Low battery alert When the battery level is lower than 10%, your band will vibrate to remind you. Buttons and gestures Your band comes equipped with a touchscreen. -
Page 6: Changing Watch Faces
This feature is only available in some countries and regions. For more information, contact • the official Honor service hotline. Notifications Once the notifications feature is enabled, the band can sync notifications displayed in the phone's notification panel to your band. -
Page 7: Setting Alarms
Getting started Your band will receive notifications but will not notify you during workouts, Do Not Disturb • mode, Low battery alert, Sleep mode or not wearing the band. Swipe up on the home screen to view new messages. You will not receive any app notifications on your wearable device if the chat is also open •... -
Page 8: Receiving Weather Reports
Getting started Event alarms are synced between the band and Health app. • There is only one smart alarm by default. You cannot add more or delete the smart alarm. • You can set a maximum of five event alarms. The smart alarm may vibrate in advance if it detects that you woke up before the alarm is •... -
Page 9: Incoming Calls
Getting started Viewing pushed weather reports Method 1: View the weather information on the weather screen • Swipe right on the band screen until you find the weather screen, then you can check your • location, the latest weather, temperature, air quality, and more. Method 2: View the weather information on the weather watch face •... -
Page 10: Workout Modes
Magic UI 2.0 or later, or iOS 9.0 or later. If all these conditions are met, your band can record your workout once the workout starts. Outdoor cycle is supported on Honor phones running Magic UI 2.0 or later and iPhones •... -
Page 11: Viewing Workout Records
Workout modes Viewing workout records Viewing workout records on the band On your band, enter the app list and touch Workout records. Then select a record to view the details. Your band will display different data types for different workouts. •... -
Page 12: Automatic Workout Detection
Workout modes Automatic workout detection Your band can identify your workout status on its own. This feature is disabled by default. To use it, you need to enable it manually. After you have enabled Auto-detect workouts under Settings > Workout settings, the wearable will remind you to start the workout if it detects that there is a change in your activity intensity and suggests a workout mode for you. -
Page 13: Health Management
Health management Sleep tracking Your band collects sleep data and identifies your sleep status when you wear it while sleeping. It can automatically detect when you fall asleep and wake up and whether you are in a light or deep sleep. Your sleep data for a single day is measured from 8:00 PM the night before to 8:00 PM of that day for a total of 24 hours. -
Page 14: Monitoring Your Heart Rate
Health management This feature is only available in some countries and regions. For more information, contact • the official Honor service hotline. The reading will be interrupted if you swipe right on the band screen, receive an incoming • call, or an alarm goes off. - Page 15 Health management Open Health, touch Devices then your device name, go to Health monitoring > Continuous heart rate monitoring, and enable Continuous heart rate monitoring. Then your band will measure your resting heart rate on its own. If you disable Continuous heart rate monitoring after taking your resting heart rate, the •...
-
Page 16: Heart Rate Alerts
Health management Heart rate alerts Once you have set an upper limit for your heart rate during workouts, your band will vibrate once if your heart rate exceeds the value for over 10 seconds during a workout. At the same time, it will vibrate and display an alert message on your screen. -
Page 17: Performing A Stress Test
Health management You can set the low heart rate value to the following: 40 bpm, 45 bpm, or 50 bpm. • Performing a stress test To perform a stress test, open Health, touch Devices then your device name, go to Health monitoring >... - Page 18 This feature is only available with Android 5.0 or later. • This feature is only available in some countries and regions. For more information, contact • the official Honor service hotline. Touch Records to view and modify period data. The predicted period is marked in the • dotted line.
-
Page 19: Handy Features
If the number calls again, the new tag will be displayed along with their phone number on your phone and band. Requires a Honor phone running Magic UI 2.0 or later. Stopwatch On the band, enter the app list, swipe on the screen, and touch Stopwatch. -
Page 20: Flashlight
Handy features Touch to start the timer, touch to pause the timer, or touch to exit the timer. Swipe right on the screen or press the button to move Timer to the background. • The band will vibrate to inform you when the time is up. •... - Page 21 Swipe right on the screen or press the button on the band to close Camera and exit Remote shutter. Requires Honor phones that run Magic UI 2.0 or later. Touch to switch between a 2-second and 5-second timer.
-
Page 22: More Guides
More guides Do Not Disturb mode Swipe on the band screen to display the menu, touch to enable Do Not Disturb. Alternatively, enter the app list, go to Settings > Do Not Disturb, and schedule a period for this mode. After Do Not Disturb is enabled: The band will not vibrate to notify you of incoming calls or notifications, and the Raise to •... -
Page 23: Restoring The Band To Its Factory Settings
More guides To set the screen sleep time, on your band, go to Settings > Display > Advanced and set the sleep time to 10 sec, 15 sec, 20 sec, or Auto. If Sleep is set to Auto, the band screen will turn off when you tilt or lower your wrist. -
Page 24: Water And Dust Resistance
More guides Viewing the MAC address: Press the button and go to Settings > About to view the MAC address of the device. Viewing the SN: Press the button and, go to Settings > About. The name displayed under SN is the serial number of the device.
Need help?
Do you have a question about the Band 6 and is the answer not in the manual?
Questions and answers