Page 1
MusiCall Gebruikers handleiding User manual...
Page 3
MusiCall gebruikers handleiding Inleiding Veiligheidsinstructies Alle veiligheidsinstructies, waarschuwingen en gebruiksaanwijzingen moeten als eerste gelezen worden. Alle op het apparaat aanwezige waarschuwingen dienen opgevolgd te worden. De gebruiksaanwijzing dient opgevolgd te worden. Bewaar de gebruiksaanwijzing voor toekomstig gebruik. Het apparaat mag nooit in de onmiddellijke nabijheid van water worden gebruikt;...
Page 5
Pset Monit or Power De Qfm is een viervoudige FM-ontvanger die voor de MusiCall centrale is ontwikkeld. De Qfm kan met behulp van een dataverbinding communiceren met de MusiCall centrale. Hierdoor kan de ontvangen RDS-data over het MusiCall netwerk worden doorgegeven.
Page 6
Inleiding MusiCall gebruikers handleiding Bedieningseenheden WallUnits MRC1 De WallUnits worden in de verschillende ruimtes (zones) opgehangen en met behulp van een tweedraadsverbinding aangesloten op de centrale. De WallUnits passen in een standaard inbouwdoos. Met de WallUnits kan de gebruiker het volume instellen en een audiobron kiezen.
Page 7
MusiCall gebruikers handleiding Bediening Bediening MRC1 WallUnits De geluidsbron in de ruimte kan worden aangepast door op ‘channel +’ of ‘channel -‘ te drukken. Het aantal geluidsbronnen en de volgorde ervan is afhankelijk van de configuratie van het systeem. Maximaal kunnen er 16 verschillende bronnen beschikbaar zijn.
Page 8
Bediening MusiCall gebruikers handleiding Consoles Gebruikers oproepen Elke zone kan afzonderlijk MPC-8 worden toegesproken door op de knoppen 1...8 te drukken. •••••••••••••••••••• MusiCall Het lampje in de knop zal eerst •••••••••••••••••••• rood oplichten; nu klinkt een ding- •••••••••••••••••••• MultiZone Paging dong geluid.
Page 9
MusiCall gebruikers handleiding Configureren Configuratie aanpassen Met het console kunnen bijna alle instellingen van het systeem worden aangepast. Hiervoor moet het systeem wel zodanig zijn geconfigureerd dat de programmeermode kan worden bereikt met het console. Dit is bij elk console afzonderlijk in te stellen.
Page 10
Configureren MusiCall gebruikers handleiding Ingangen configureren Ingangen die (tijdelijk) ongebruikt zijn kunnen in het systeem inactief worden gemaakt. Als een gebruiker door de audio-bronnen heen loopt zullen de inactieve ingangen worden overgeslagen. Dit kan handig zijn wanneer audio-bronnen tijdelijk worden verwijderd.
MusiCall user manual Safety instructions Safety instructions All safety instructions, warnings and operating instructions must be read first. All warnings on the equipment must be heeded. The operating instructions must be followed. Keep the operating instructions for future reference. The equipment may never be used in the immediate vicinity of water; make sure that water and damp cannot get into the equipment.
Page 15
The Qfm contains four stereo RDS FM-tuners and is developed to operate together with the MusiCall system. The Qfm has a dataport to communicate with the MusiCall system. This makes it possible to distribute the RDS information over the system.
Page 16
Introduction MusiCall user manual Controllers WallUnits MRC1 The WallUnits are mounted into the different rooms (zones) and connected to the central unit with a two-wire cable. The WallUnits will fit into a standard double-gang electrical box. The WallUnits are used to select the audio-source and adjust the volume in the room.
MusiCall user manual Oeration Operation MRC1 WallUnits The audio-source in the room can be changed by pressing the ‘channel +’ or the ‘channel -‘ keys. The number of sources and the sequence depends on the systems configuration. A maximum of 16 sources can be configured.
Page 18
Operation MusiCall user manual Consoles Paging a user Each zone can be paged to MPC-8 separately by pushing the keys 1...8. •••••••••••••••••••• MusiCall The lamp will light up red; a •••••••••••••••••••• chime will be heard. When the •••••••••••••••••••• MultiZone Paging light illuminates green a page can ••••••••••••••••••••...
MusiCall user manual Configuration Configuring the system The console can change almost all of the system settings. The system has to be configured to allow the programming mode from the specific console. The program function can be enabled or disabled for each console separately.
Configureren MusiCall gebruikers handleiding Configure inputs Temporarily unused inputs can be made inactive within the system. Whilst scrolling through the available inputs, the inactive inputs will be neglected. This can be useful when audio inputs temporarily are disconnected. When the menu is operational, active inputs will light up green, inactive inputs will light up red.
Need help?
Do you have a question about the MusiCall and is the answer not in the manual?
Questions and answers