Table of Contents
Advertisement
Quick Links
ECX – 1U/2U
QUICK START GUIDE
ES: Visite nuestra pagina web www.belden.com para obtener el guía de instalación en español.
FR: Veuillez visiter notre site web au www.belden.com pour obtenir le guide d'installation en français.
1U
Carton contents
1.
Rear door
2.
Housing
3.
Front door
4.
Sliding tray assembly
5.
Patch cord Management clip (3x)
6.
Removable cover (2x)
7.
Label cards (2x)
8.
Installation guide & labels (not shown)
9.
Hardware kit
Hardware kit contains:
(Not all parts are shown)
• Blank frame (2x)
• I.D label (3/6/12) ports (2x)
. I.D label (8/16) ports (2x)
• Management clips (8x)
• External strain relief – right (1x)
• External strain relief – left (1x)
• Intermediate strain relief (1x)
• Internal strain relief assembly (1x)
• #6-19 x ¼ ", screw for plastic (4x)
• #6-19 x ½ ", screw for plastic (2x)
• #12-24, machine screws Phillips (4x)
• #10-32, machine screw Phillips (2x)
• M4 x 5mm, Metric screw (4x)
• Cable tie – 4 " (4x)
• Cable tie – 7½ " (4x)
• Velcro 8" (4x)
NOTE: The items listed are for 1U contents only.
STANDARD RECOMMENDED PROCEDURE
2
3
4
5
External strain
relief – right
Blank frame
I.D label (3/6/12)
ports
PX106484-EN REV A
2U
1
6
7
I.D label (8/16) ports
External strain relief – left
Management clip
Internal strain
relief assembly
Intermediate strain
relief
Page 1 of 8
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Belden ECX-1U
Summary of Contents for Belden ECX-1U
- Page 1 ECX – 1U/2U QUICK START GUIDE ES: Visite nuestra pagina web www.belden.com para obtener el guía de instalación en español. FR: Veuillez visiter notre site web au www.belden.com pour obtenir le guide d’installation en français. Carton contents Rear door Housing...
- Page 2 Mounting the ECX housing Insert the bottom screws into the rack or cabinet as shown (use #12-24 or #10-32 machine screws provided in the hardware kit). Leave ¼ ” of the screw exposed. Install the housing into the rack and position the bottom slots of the mounting bracket onto the installed screws. These screws will carry the weight of the housing during the installation.
- Page 3 Removing the tray Pull the tray from both sides simultaneously with enough force to disengage from neutral position as shown. Slide the tray forward until stopping point. Squeeze latches on both sides simultaneously to release the tray as shown. Installation of frames Install the desired frame as shown.
- Page 4 Installing distribution cable for field termination IMPORTANT: Please take note that this is the recommended procedure. Prepare the cable using the following dimensions: leave 25 ” (0,64 m) of sub-unit and 84 ” (2,13 m) of 900 micron fiber. Remove the cassette guide by pulling the latch upwards and sliding it backwards. Install the intermediate strain relief and the management clips by pushing and rotating them 90 degrees.
- Page 5 Installing distribution cable for field termination (continued) Route the 900 micron fiber by using the management clips. Install connectors in the desired frame. Slide the tray from the rear of the housing Slide the tab of the internal strain relief as shown Thigthen the screw to secure it.
- Page 6 For further information on the cassette routing, please read the cassette installation guide or visit our website at www.belden.com. Measure 17.5 " (0,45 m) of sub-unit cable from the end of the cassette.
- Page 7 ECX labelling Pull out the label card. Tilt the label card upwards. Remove the label card by pushing downwards. Apply the provided adhesive label to label card. NOTE: Surface should be cleaned properly before applying label. Reinstall the label card. STANDARD RECOMMENDED PROCEDURE PX106484-EN REV A Page 7 of 8...
- Page 8 Proposed patch cord management NOTE: The tray is pulled forward to facilitate visibility. STANDARD RECOMMENDED PROCEDURE PX106484-EN REV A Page 8 of 8...
Need help?
Do you have a question about the ECX-1U and is the answer not in the manual?
Questions and answers