Advertisement
Quick Links
Instruction Sheet
TOOLS REQUIRED
•
Safety Gloves (cut resistant)
•
Oetiker Pliers (PN 00681815)
•
Needle Nose Pliers
•
Screw Drivers, Phillips & Flat Head
•
3/8" or ¼" Drive Socket Set (3/8" and 5/16")
•
Standard Open End Wrench Set
•
Soft Bristle Brush
•
Wet/Dry Shop Vacuum
•
Digital Scale (weighs in ounces to once decimal place)
PARTS REQUIRED
•
Food Grade Lubricant
•
5 - 6 ft (1.8m) ¼" I.D. X 3/8 " O.D. clear tubing
•
TUNE UP KIT 020009016 (contents listed below)
QTY
DESCRIPTION
9
Valve, Dispense Outlet, LMS
9
15.7 Oetiker Clamp
2
O-ring, replacement
1
Gasket Ice Shaver
1
Drive belt, Shaver Vitamix 1617
2
Cup Grate O-rings
1
Instructions Tune Up ENG
1
Instructions Tune Up French
1
SHAVER BLADE KIT
Subject: BIC Tune Up
SCOPE: MULTIPLEX BIC UNITS MA-8-2, MA-8-2BF, MA-8-2AF
RECOMMENDED TRUCK STOCK LIST FOR TUNE UP
QTY
PART NUMBER
1706172
15.7-706R
MCP00262
3434865
VMP00123
3547901
NOTE: Additional non-warranty parts used need to be
020009017
invoiced on a separate invoice to the site. Manager or
020009047
Operator must approve additional repairs.
VMP00125
NOTE: All right and left references are based off of standing
in front of the unit.
Ice shaver blade is sharp on both edges. Wear cut resistant gloves
645 PARK EAST BLVD SUITE 5, NEW ALBANY, IN 47150
DESCRIPTION
1
SWITCH REED RINSE AREA MOD
1
SWITCH REED RINSE AREA - GRAY
5
FUSE, 5A, MIXER BOARD
1
SWITCH, SNAP ACTION, MINI - BLEN HM
1
BOARD, SRB ,BIC, GEN2
2
CONTROL BLENDER BIC HSM
1
CONTROL, 7 IN UI, BIC
1
RELAY, 24DC COIL, DPDT
2
FUSE, 4A, DC HARNESS
1
PUMP, FLOJET, NSF, NO ASO
1
MIXER MTR, 6MM, 120V/50-60, GEN3 SW 3239822
2
ASSEMBLY, LOWER BLENDER, 6MM, GEN3 3239825
1
SOLENOID VALVE REPAIR KIT
1
VALVE, S.S. SLND, WATER, 1/4"
1
SAFETY SWITCH/RECTIFIER ASSEM- 120V VMP00113
1
SHAVER BELT
1
SHAVER BLADE KIT
1
SENSOR, HALL EFFECT
1
SHAVER MTR W/PULLEY / MAGNET 120V
3
MOTOR ISOLATION MOUNT
1
PUSH ROD
3
CUP ALIGNMENT RING INSERT
1
GASKET, ICE SHAVER
CAUTION
,
when handling.
Warning
n
Blender shaft contains sharp blades.
Do NOT touch the blades.
gloves when handling.
Document Number: 020009017 May 12, 2022
MULTIPLEX
844-724-CARE
WWW.MULTIPLEXBEVERAGE.COM
Refreshing the Experience
PART NUMBER
2160033
2162748
2193015
2194807
2195346
2195363
000-BIC-01F9-S
2196069
2198785
3239675
020005547
000-BIC-01B5-S
VMP00123
VMP00125
VMP00175
VMP00172
9324159
VMP00134
1708685
3434865
Wear cut resistant
1 of 9
Advertisement
Related Manuals for Multiplex BIC MA-8-2
Summary of Contents for Multiplex BIC MA-8-2
- Page 1 645 PARK EAST BLVD SUITE 5, NEW ALBANY, IN 47150 844-724-CARE WWW.MULTIPLEXBEVERAGE.COM Refreshing the Experience Instruction Sheet Subject: BIC Tune Up SCOPE: MULTIPLEX BIC UNITS MA-8-2, MA-8-2BF, MA-8-2AF TOOLS REQUIRED RECOMMENDED TRUCK STOCK LIST FOR TUNE UP • Safety Gloves (cut resistant) DESCRIPTION...
- Page 2 Subject: BIC Tune Up PREPARATION 7. Replace with new O-rings over the tip on both grates. 8. Wash, rinse and sanitize the blender and dispense grates. 1. Verify operation with manager. Note any issues on checklist and take pictures. 9. Prepare a five (5) gallon bucket with luke-warm tap water (no hotter than 105°F/40.5°C) and cleaning 2.
- Page 3 Subject: BIC Tune Up 15. Turn unit OFF and unplug. 17. Using a Phillips head screw driver remove the two (2) screws from the metal mounting plate that secures a block of three (3) LMS valves to the dispensing valve mounting plate.
- Page 4 Subject: BIC Tune Up NOTE: The tubing orientation is 1-9 in a counter clockwise 25. Carefully remove the ice bin using caution not to manner as shown. damage the micro switch push rod. Use caution not to lose any of the three (3) ice bin grommets attached to 22.
- Page 5 Subject: BIC Tune Up 34. Reinstall the ice bin to the condensate bowl using the 38. Locate the four (4) hex head bolts that secure the four (4) screws. shaver motor to the motor mounting bracket. NOTE: Use caution not to damage the push rod. A.
- Page 6 Subject: BIC Tune Up 43. Remove and replace the O-rings on both the water and 52. Repeat previous step until each drain line runs clear. CO2 supply lines. 53. Reconnect incoming water and CO supply lines and pressure, observe for any leaks. 54.
-
Page 7: Calibration & Settings
Subject: BIC Tune Up 57. Once the 35 psi dynamic setting has been achieved CALIBRATION & SETTINGS push the knob back to the downward position and turn 61. Fill the ice bin with ice. OFF the water solenoid and/or the product solenoid. 62. -
Page 8: Confirm Operation
72. Maintain a copy of the Tune Up Checklist to be Select “A” for the password submitted along with the invoice for payment. Select the GREEN check 73. Submit claim for service work through Multiplex Claims Select CONFIGURE SLOTS Processing System. Select CALIBRATE FLAVOR Select flavor in slot 1 and follow the onscreen calibration instructions. - Page 9 7592 or rise.callcenter@welbilt.com cover? Clean the surface areas? Step 31 page 4. ‰ Submit claim for service work through Multiplex Claims Processing System. ‰ Replace the shaver gasket? Step 33 page 4. Tune Up Checklist MUST be attached to claim or claim will be DENIED.