Electronic Function - Makita CS002G Instruction Manual

Dust case
CAUTION:
Do not touch metal chips and the
dust case with bare hands immediately after the
operation. They may be extremely hot and could
burn your skin.
CAUTION:
Do not cut the material on which
thinner, gasoline, grease, or other chemicals are
applied. The metal chips of such materials can dam-
age the dust case and result in breakage which can
cause personal injury.
CAUTION:
Wear eye protection or goggle
when emptying the dust case.
Metal chips are collected into the dust case. Periodically
dump the metal chips before the metal chips become
visible through the sight window.
► Fig.7: 1. Sight window 2. Dust case
Push the latch button on the dust case to remove the
dust case. Dump the metal chips while the inside of the
dust case faces downward.
► Fig.8: 1. Latch button
► Fig.9
After dumping the metal chips, set the dust case.
Align the hole on the dust case with the hook on the
tool.
At this time, align the "I" marking as illustrated so that
you can set the dust case in the proper position.
Then, insert the hook on the latch button to the hole on
the tool.
► Fig.10: 1. Hole on the dust case 2. Hook on the
tool 3. Hook on the latch button 4. Hole on
the tool
► Fig.11: 1. "I" marking
NOTICE:
Make sure that each hook is secured
with the holes.
Electric brake
This tool is equipped with an electric blade brake. If the
tool consistently fails to quickly stop the circular saw
blade after switch trigger released, have tool serviced at
a Makita service center.
CAUTION:
The blade brake system is not a
substitute for blade guard. NEVER USE TOOL
WITHOUT A FUNCTIONING BLADE GUARD.
SERIOUS PERSONAL INJURY CAN RESULT.

Electronic function

The tools equipped with electronic function are easy to
operate because of the following feature(s).
Soft start feature
Soft start because of suppressed starting shock.
Constant speed control
Electronic speed control for obtaining constant speed.
Possible to get fine finish, because the rotating speed is
kept constant even under load condition.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Hex wrench storage
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
► Fig.12: 1. Hex wrench
Installing or removing the circular
saw blade
CAUTION:
Use only the Makita wrench to
install or remove the circular saw blade.
CAUTION:
When installing the circular saw
blade, be sure to tighten the bolt securely.
CAUTION:
Be sure the circular saw blade is
installed with teeth pointing up at the front of the
tool.
1. Remove the dust case.
2. Press the shaft lock fully so that the circular saw
blade cannot revolve and use the hex wrench to loosen
the hex bolt.
► Fig.13: 1. Shaft lock 2. Hex wrench 3. Tighten
4. Loosen
3. Remove the hex bolt, outer flange and circular
saw blade.
► Fig.14: 1. Hex bolt 2. Outer flange 3. Circular saw
blade 4. Inner flange
4.
To install the circular saw blade, follow the
removal procedure in reverse.
5. After installing the circular saw blade, set the dust
case again.
► Fig.15: 1. Hole on the dust case 2. Hook on the
tool 3. Hook on the latch button 4. Hole on
the tool
WARNING:
BOLT SECURELY. Also be careful not to tighten
the bolt forcibly. Slipping your hand from the hex
wrench can cause a personal injury.
WARNING:
be sure to install it on the spindle. When install-
ing, choose a correct side on which protrusion
fits into the circular saw blade hole perfectly.
Mounting the circular saw blade on the wrong side
can result in the dangerous vibration.
11 ENGLISH
BE SURE TO TIGHTEN THE HEX
If the inner flange is removed,