Operating manual Table of contents INTRODUCTION ......................... 3 DESCRIPTION AND OPERATION OF THE PRODUCT ..........4 Description ..........................4 Technical specifications ......................4 Structure and operation of the Product .................. 5 Measurement instruments, tools and appliances ..............6 Marking and sealing ......................6 Packaging ..........................
INTRODUCTION This operating manual (hereinafter – OM) describes composition, structure, op- eration and technical service of power supply units PS-203-12.5, PS-203-6.5 and PS-203-3.3 types (hereinafter – the Product). In addition to the instructions given in this document, the safety regulations and rules applicable in the field shall be observed.
Power supply unit PS-203 1.3 S TRUCTURE AND OPERATION OF THE RODUCT 1.3.1 The Product is manufactured in metal casing, where a piano type power switch (on/off) and fuse holder are located, see Figure 1. Figure 1 – the Product Table 2 below describes functional elements and controls of the Product.
Operating manual “L” 1.3.2 To connect input power supply, terminals “N”, loads – “–V” and “+V”, see Figure 2. Figure 2 – Connection diagram of the Product 1.4 M EASUREMENT INSTRUMENTS TOOLS AND APPLIANCES Table 3 below describes consumables required for the TS. Table 3 –...
Power supply unit PS-203 1.6 P ACKAGING When delivered, the Product is packed in a corrugated board box and inner packaging (air bubble film) ensuring its transportation and storage at the warehouse. Transport packaging is also used as a returnable packaging for transportation of the Product to the repair location and back.
Operating manual INTENDED USE OF THE PRODUCT PERATIONAL LIMITATIONS Select an installation place in compliance with operational limitations (operating temperature and protection degree). Caution! Distance between the installation site and magnetic compass shall not be less than 1 m! SAGE PREPARATIONS 2.2.1 Safety features While preparing the Product for operation, check it visually and make sure there is no mechanical damage.
Power supply unit PS-203 2.2.4 To switch the Product off: a) transfer the piano type switch “ON/OFF” on the casing to “OFF” position; b) transfer circuit breakers of main power switchboard to “OFF” position; c) disconnect de-energized power cable from the Product. SAGE OF THE RODUCT To operate the Product:...
Operating manual TECHNICAL SERVICE OF THE PRODUCT 3.1 G ENERAL DESCRIPTION Before performing the TS the staff shall familiarize with the Product structure and operation features. In order to provide safe and reliable operation for the Product, the staff shall maintain semi-annual TS.
Power supply unit PS-203 Table 6 – CL №2. Test of output voltage Man-hours To be done Routine per 1 Product 1 Switch on the Product power supply 2 Connect a voltmeter to output terminals of the 1 person Product Test of output voltage 15 mins 3 Supply power to the Product...
Operating manual CURRENT REPAIR OF THE PRODUCT 4.1 G ENERAL DESCRIPTION To provide diagnostics of the problems, see Table 7. If a problem cannot be diagnosed or trouble shooting cannot be provided, con- tact the Manufacturer’s service center. 4.2 S AFETY FEATURES Only qualified personnel, examined in occupational safety may perform repair works.
Power supply unit PS-203 STORAGE The Product must be stored in packaging inside areas complying with the re- quired storage conditions (+5°С to +40°С) with the concentration of dust, oil, moisture and aggressive impurities in the air within the required limits for the working areas of production facilities.
Operating manual TRANSPORTATION The Product must be transported in the Manufacturer's transportation package in closed means of transport. Types of shipment: - motor vehicle and railroad transportation in closed means of transport (covered cars, multipurpose containers); - air transportation (in sealed and heated compartments); - sea transportation (in dry service spaces).
Power supply unit PS-203 DISPOSAL New equipment, the parts of the Product damaged during operation, and any outage equipment must not be disposed as standard household wastes, since they con- tain the materials suitable for re-use. Decommissioned and non-used components of the Product must be delivered to a special waste disposal center licensed by local authorities.
OM. The Manufacturer will not consider damage claims in case of violation of operating conditions. More information about warranty terms you can find on the official site of “NPK MSA” LLC, section Support. Address and contacts of the Manufacturer's service centre: “NPK MSA”, LLC 26E, Kibalchicha str., 192174, St Petersburg, Russia...
Need help?
Do you have a question about the PS-203-12.5 and is the answer not in the manual?
Questions and answers