Related Manuals for MSA PS-203-60
Summary of Contents for MSA PS-203-60
- Page 1 «NPK Morsvyazavtomatica» LLC» POWER SUPPLY UNIT PS-203-60 Operating manual 26E, Kibalchicha Str., St Petersburg Tel.: 8 (800) 100-67-19 info@unicont.com Russia, 192174 Fax: +7 (812) 362-76-36 www.unicont.com...
-
Page 2: Table Of Contents
Operating manual Table of contents INTRODUCTION ......................... 3 DESCRIPTION AND OPERATION OF THE PRODUCT .......... 4 Description ..........................4 Technical specifications ......................4 Structure and operation of the Product .................. 5 Measurement instruments, tools and appliances ..............7 Marking and sealing ......................7 Packaging .......................... -
Page 3: Introduction
PS-203-60 INTRODUCTION This operating manual (hereinafter – OM) describes composition, structure, op- eration and technical service of power supply units PS-203-60 (hereinafter – the Prod- uct). In addition to the instructions given in this document, the safety regulations and rules applicable in the field shall be observed. -
Page 4: Description And Operation Of The Product
Operating manual DESCRIPTION AND OPERATION OF THE PRODUCT 1.1 D ESCRIPTION The Product supplies different shipborne and industrial equipment with regulat- ed voltage 24 V DC. The Product has integrated functions of load redundancy (power), and load switching to external SB or emergency DC network in case of main power failure. -
Page 5: Structure And Operation Of The Product
The LED operates when the switch is turned to power On position, see Figure 1. Figure 1 – The PS-203-60 Table 2 describes functional elements and controls of the Product. Table 2 – Functional elements, controls and LED light indicators of the Product Type, size, identifi- №... - Page 6 If there is no input power, dry contacts relay actuates alarm signal- ing. SB voltage to power external signaling unit AU-106 (AU-206) is connected to «Alarm» terminal. Table 3 describes assignment of connector terminals. Figure 2 – Connection diagram Table 3 – Assignment of PS-203-60 connector terminals Terminal Connector Description №...
-
Page 7: Measurement Instruments, Tools And Appliances
Power supply unit PS-203-60 1.4 M EASUREMENT INSTRUMENTS TOOLS AND APPLIANCES Table 4 below describes consumables required for the TS. Table 4 – Consumables required for the TS Amount of Name and identifier of consumables Note consumables 1 To clean the Product surfac- es –... -
Page 8: Intended Use
Operating manual INTENDED USE PERATIONAL LIMITATIONS Select an installation place in compliance with operational limitations (operating temperature and protection degree). Caution! Distance between the installation site and magnetic compass shall not be less than 1 m! SAGE PREPARATIONS 2.2.1 Safety features While preparing the Product for operation, check it visually and make sure there is no mechanical damage. - Page 9 Power supply unit PS-203-60 f) check the Product connection; check main power supply by green LED on the piano type switch; make sure there is no alarm on dry contacts; g) using voltmeter, measure output voltage on connectors’ contacts (for load connection);...
-
Page 10: Technical Service Of The Product
Operating manual TECHNICAL SERVICE OF THE PRODUCT 3.1 G ENERAL DESCRIPTION Before performing the TS the staff shall familiarize with the Product structure and operation features. In order to provide safe and reliable operation for the Product, the staff shall maintain semi-annual TS. - Page 11 Power supply unit PS-203-60 Table 5 – TS works CL № Name of work Visual check of the Product Test of output voltage Note – «+» – work is obligatory. Table 6 – CL № 1. Visual check Man-hours To be done...
-
Page 12: Current Repair Of The Product
Operating manual CURRENT REPAIR OF THE PRODUCT 4.1 G ENERAL DESCRIPTION To provide diagnostics of the problems, see Table 8. If a problem cannot be diagnosed or trouble shooting cannot be provided, con- tact the Manufacturer’s service center. 4.2 S AFETY FEATURES Only qualified personnel, examined in occupational safety may perform repair works. -
Page 13: Storage
Power supply unit PS-203-60 STORAGE The Product must be stored in packaging inside areas complying with the re- quired storage conditions (+5°С…+40°С) with the concentration of dust, oil, moisture and aggressive impurities in the air within the required limits for the working areas of production facilities. -
Page 14: Transportation
Operating manual TRANSPORTATION The Product must be transported in the Manufacturer's transportation package in closed means of transport. Types of shipment: - motor vehicle and railroad transportation in closed means of transport (covered cars, multipurpose containers); - air transportation (in sealed and heated compartments); - sea transportation (in dry service spaces). -
Page 15: Disposal
Power supply unit PS-203-60 DISPOSAL New equipment, the parts of the Product damaged during operation, and any outage equipment must not be disposed as standard household wastes, since they con- tain the materials suitable for re-use. Decommissioned and non-used components of the Product must be delivered to a special waste disposal center licensed by local authorities. -
Page 16: Warranty
OM. The Manufacturer will not consider damage claims in case of violation of operating conditions. More information about warranty terms you can find on the official site of «NPK MSA» LLC, section Support. Address and contacts of the Manufacturer's service centre: «NPK MSA», LLC 26E, Kibalchicha str., 192174, St Petersburg, Russia... -
Page 17: Appendix A (Mandatory) Regulatory Documents
Power supply unit PS-203-60 APPENDIX A (MANDATORY) REGULATORY DOCUMENTS Figure A.1 – Outline and installation dimensions of the Product While mounting, provide 200 mm free space from surface A to connect the Prod- uct. Page 17...
Need help?
Do you have a question about the PS-203-60 and is the answer not in the manual?
Questions and answers