Page 1
Sonix lo Technical Manual SONIX Input/Output Unit...
Page 2
MODIFY ANY CONTRACT BETWEEN THE PARTIES. In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or other-wise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not...
Page 3
A 2Mx bus, used to communicate with SAS application Sync A 2Mx bus used to communicate with the second 2Mx unit when PA/GA system is confi gured as A&B, AB+ or N+1 system SONIX IO TECHNICAL MANUAL TM366 / A June 2022 www.eaton.com...
3.1 Product description In the interest of preserving the environment, Eaton aims The Sonix Io unit is designed to act as an interface to use recycled packaging wherever practical. Due to the between external systems and the Sonix PA/GA system.
48 V dc, recommended taken from Sonix Pm10 unit Auxiliary Mute Current: 100 mA max consumption Ship’s Whistle System Busy Important Message Alarm Cancel Alarm Attenuate Alarm Inhibit SCREEN Figure 1 - Sonix Io Unit SONIX IO TECHNICAL MANUAL TM366 / A June 2022 www.eaton.com...
Earth. The Earth connection is used as a functional reference for the unit screening only. The Sonix Io is a DIN rail mount unit, intended to be mounted inside the PA/GA cabinet on most standard EN It is strongly recommended that any connection be...
PCB. This change is defined on each input cables do not exceed 25 meters in length, regardless of the system independently. configuration. 4.5 Input connections The Sonix Io unit has several inputs that can be Volt-free Driven configured to be volt-free or driven. Each input is Volt-free Driven independent and can be configured as required.
Inhibit Figure 6 - Isolated input for > 12 V source Figure 8 - Output polarity jumper configuration Global Fault ote: The Sonix Io input should be configured as volt-free when using Entertainment Volt-free Driven Line-level Mute an external isolating relay.
5.2 Audio input GA system. Input The Sonix Io has 2 audio inputs: Pbx and Aux (-iliary). Most of the input and outputs on the Sonix Io are configured in ote: System Busy software, please see the SAS manual for more details.
See SAS manual for more details. 5.2.5 Emergency speech chime The Sonix Io can be configured to play one of three 5.3 Audio Output different chimes before each emergency speech broadcast. These chimes are different to the routine The Sonix Io has a single audio output, with transformer speech chimes.
Sonix PA/GA system. 5.4.1 Fault outputs 5.5.1 Alarm Cancel The Sonix Io unit has 2 fault outputs, Global Fault and The Alarm Cancel input generates a short, approximately Program Fault, also known as Major and Minor faults 2 seconds, active pulse when the input is first activated respectively.
Sonix Io Unit Technical Manual 6 Configuration 7 Customisation The configuration options are detailed within the SAS The standard version of the Sonix Io unit has been manual. designed with mostly fixed function inputs and outputs and some limited configuration., any customisations should be discussed with your local Eaton representative 6.1 Ping-set...
Page 15
Sonix Io Unit Technical Manual SONIX IO TECHNICAL MANUAL TM366 / A June 2022 www.eaton.com...
Page 16
All specifications, dimensions, weights and tolerances are nominal (typical) T: +44 (0) 1623 444 400 Publication www.crouse-hinds.com/hac No.TM366 / A and Eaton reserve the right to vary all data without prior notice. No liability is accepted for any consequence of use. MEDCSales@Eaton.com June 2022...
Need help?
Do you have a question about the SONIX Io and is the answer not in the manual?
Questions and answers