BLUEDENT SMART cordless Dental curing light Thank you for trusting our products! Carefully read this Operating instructions manual before installing and operating the unit to use and maintain it successfully! Save this Operations guide for your reference it in the future.
BLUEDENT SMART cordless Dental curing light II. TECHNICAL DATA 1. Operating voltage: - Handpiece - 3.7V Li Ion battery (2600mAh capacity) - Adapter – type SYS1381N-1209-W2E, 100-240V AC / 50-60Hz / 9V DC / 1.33A, power consumption - 0.5A max - Charging station - 9VDC, power consumption - 0.8A max...
Page 5
BLUEDENT SMART cordless Dental curing light - Strong electromagnetic fields in the building can cause interference and malfunction of the device. If their source cannot be determined, change the location of the device and plug it into another socket or other room, even in another building.
Page 6
BLUEDENT SMART cordless Dental curing light - the device or any of its parts must not be disassembled while it is connected to the mains! Protect the cables of the appliance from insulation damage and breakage from sharp objects, strong pulling, rodents, chemicals. If such damage is noticed on the electrical cables, it is necessary to take the device immediately to the company service.
BLUEDENT SMART cordless Dental curing light 4. Fire safety - Keep the device away from solvents, flammable liquids and powerful heat sources. - Do not expose to direct sunlight. - Do not allow liquids and detergents to enter the device, as this may cause a short circuit and fire or cause potentially dangerous damage.
Page 8
BLUEDENT SMART cordless Dental curing light 3. Mount lightguide and protection shield or protection cap. See VI. ROUTINE CARE AND MAINTENANCE for instructions of initial cleaning and mounting. NOTE: Lightguide and protection cap must be sterilized before every use! They are delivered in a non-sterile state and must be sterilized beforehand first use.
Page 9
BLUEDENT SMART cordless Dental curing light L - LONG mode (1-9 min) The light intensity is at a maximum level of 100%, the mode is suitable for long procedures, e.g. teeth whitening. F - FAST mode (10 - 20 - 30 sec) The emitted light has a high intensity - 100% without a soft start to achieve complete polymerization.
Page 10
BLUEDENT SMART cordless Dental curing light 5. The device is started by pressing Start / Stop probe button - see figure. After starting, the timer starts counting down. An audible signal sounds every 10 seconds. 6. The handpiece is aimed at the place designated for...
BLUEDENT SMART cordless Dental curing light F - FAST - 4 light points. P - PULSE - 3 and 4 alternating illumination points. We recommend that the light intensity be measured in FAST mode. If the light intensity is below 80% (less than 3 LEDs are lit), it is necessary to check the fiber for stuck photocomposite material or mechanical defects.
Page 12
BLUEDENT SMART cordless Dental curing light Remove the light guide and looking through it at strong light: if there are darkened areas over 10% of the area, replace it with a new one. Defective Lightguide should be sterilized by autoclave at 134° C for 5 min.
Page 13
BLUEDENT SMART cordless Dental curing light Lines movement Fully charged battery Timer flashes Low battery Battery charging Indication is lit for low battery Put handpiece to 30sec 5-10% charge! charge! Use only original BLUEDENT SMART Li-Ion batteries with factory label (h 65 mm, dia.18 mm), 3.7 V, TYPE 18650 - 2600 mAh.
BLUEDENT SMART cordless Dental curing light VII. WARRANTY CONDITIONS 1. Warranty period of BLUEDENT dental curing light is 24 (twenty four) months from the date of purchase. If date of purchase is not written, warranty starts at date of production.
BLUEDENT SMART cordless Dental curing light 4. The manufacturer provides its customers once a year (and in case of a situation - immediately) to check in the company service whether the performance of the devices is within the acceptable limits.
Dental curing light IX. SYMBOLS Manufacturer BG LIGHT LTD, 155, Vasil Aprilov blvd., 4027 Plovdiv, Bulgaria Pursuant to Directive 2012/19/EU, this symbols shows that the product must not be disposed of as urban waste at the end of its operating life.
BLUEDENT SMART cordless Dental curing light X. FAQ Problem Solution There is no indication “ON” on Check the adapter, cable and whether it is the charging station plugged into the charging station. Check for metal objects on the contact system of the charging station.
Page 18
BLUEDENT SMART cordless Dental curing light The power cord or AC adapter Send to the service. is damaged Liquid entering the device Send to the service. After falling to the floor, the Send to the service. device does not work properly...
BLUEDENT SMART cordless Dental curing light XII. BLUEDENT DATA LOT: DATE OF PRODUCTION: DATE OF PURCHASE: Last revision: 01.09.2021 Follow www.bglight.com for updated revision of this Operating instructions manual.
Need help?
Do you have a question about the BLUEDENT SMART cordless and is the answer not in the manual?
Questions and answers