Table of Contents
Advertisement
Quick Links
INSTRUCTIONS
BX3M-PSLED
Power supply for LED
This instruction manual is for the power supply for LED BX3M-PSLED.
To ensure the safety, obtain optimum performance and to familiarize yourself fully with
the use of this product, we recommend that you study this manual thoroughly before
operating this product, and always keep this manual at hand when operating this product.
Retain this instruction manual in an easily accessible place near the work desk for future
Optical Microscope Accessory
reference.
Advertisement
Table of Contents
Related Manuals for Olympus BX3M-PSLED
Summary of Contents for Olympus BX3M-PSLED
- Page 1 BX3M-PSLED Power supply for LED This instruction manual is for the power supply for LED BX3M-PSLED. To ensure the safety, obtain optimum performance and to familiarize yourself fully with the use of this product, we recommend that you study this manual thoroughly before operating this product, and always keep this manual at hand when operating this product.
- Page 2 Refer to your local Olympus distributor in EU for return and/or collection systems available in your country. NOTE: This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
-
Page 3: Table Of Contents
Table of Contents Introduction ............................... Safety precautions ..........................1 Nomenclature of respective portions ................2 Operation procedures ........................ Turning ON the main switch .................................8 Adjusting the brightness ..................................8 3 Specifications ............................. 4 Troubleshooting ..........................5 Assembly ..............................6 Proper selection of the power supply cord ............ -
Page 5: Introduction
BX3M-PSLED Introduction The power supply for LED BX3M-PSLED is a control box which is used to control LED light source installed on the microscope. Contents of instruction manuals This instruction manual is for power supply for LED BX3M-PSLED. For usage in combination with microscope, refer to the... -
Page 6: Safety Precautions
Safety precautions If the product is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the product may also be damaged. Always use the product according to this instruction manual. The following symbols are used in this instruction manual. - Page 7 BX3M-PSLED CAUTION - Electric safety - Always use the power cord provided by Olympus. If the proper AC adapter and the power cord is not used, the electric safety and the EMC (Electro-Magnetic Compatibility) performance of the product cannot be assured.
- Page 8 CAUTION - Protection of electrick shock - Keep the power cord and cables sufficiently away from the lamp housing. If the power cord and cables contact a hot area of the lamp housing, they could melt and cause electric shock. CAUTION - LED (light emitting diode) - Do not look directly at the light from the LED light source for a long time.
- Page 9 Indicates a non-specific general hazard. Follow the cautions given after this symbol or in the instruction manual. Indicates that the main switch is ON. Indicates that the main switch is OFF. When caution labels are dirty or peeled off, contact Olympus for replacement or inquiries.
- Page 10 Handling precautions · This product is a precision instrument. Handle it with care and avoid subjecting it to a sudden or severe NOTE impact. · Never disassemble any part of the product. Otherwise, failure could be caused. · Do not use this product in areas where it may be subjected to direct sunlight, high temperature and/or humidity, dust or vibrations.
-
Page 11: Nomenclature Of Respective Portions
BX3M-PSLED Nomenclature of respective portions As to attaching procedures to the microscope and other units, refer to the instruction manual of dedicated system. Brightness control knob B X 3 M - P S L E LED cable connector AC adapter jack... -
Page 12: Operation Procedures
Operation procedures Turning ON the main switch B X 3 M - P S L E Set the main switch a to (ON). Adjusting the brightness Turn the brightness control knob b clockwise to increase the brightness of the illumination. -
Page 13: Specifications
BX3M-PSLED Specifications Item Specification Main unit: input: 5 V / 2.5 A Rating AC adapter: input: 100-240 V 50-60 Hz 0.4 A output: 5 V 2.5 A Power consumption 5.3 W, 17.2 VA Cooling system Natural circulation air cooling The number of controllable... -
Page 14: Troubleshooting
Depending on how you use, the performance of this power supply for LED may not be exhibited, though they are not failure. If problems occur, please review the following list and take remedial action as needed. If you cannot improve the phenomena after checking the entire list, please contact Olympus for assistance. Phenomena... -
Page 15: Assembly
BX3M-PSLED Assembly · Before connecting or disconnecting cables, set the main switch to (OFF) and unplug the power cord NOTE from the outlet. · Cables are vulnerable when bent or twisted. Never subject them to excessive force. · Connect the connectors in the correct orientation paying attention to the shape of the connector. - Page 16 Insert the AC adapter plug a firmly in the AC adapter jack b of the power supply for LED. When inserting or removing the AC adapter plug, hold the NOTE plug and insert straightly. Insert the power cord connector c in the connector d of the AC adapter.
- Page 17 BX3M-PSLED Connect the power cord plug e to the power outlet f . For the safety purpose, connect the power cord plug last. NOTE...
-
Page 18: Proper Selection Of The Power Supply Cord
If no power supply cord is provided, please select the proper power supply cord for the product by referring to “Specifications” and “Certified Cord” below: Caution : In case you use a non-approved power supply cord for Olympus products, Olympus can no longer warrant the electrical safety of the product. - Page 19 BX3M-PSLED Certification mark Country Agency Country Agency Certification mark Argentina IRAM Italy Australia Japan JET, JQA, Austria ÖVE Netherlands KEMA Belgium CEBEC Norway NEMKO Canada Spain Denmark DEMKO Sweden SEMKO Finland Switzerland United ASTA France Kingdom Germany U.S.A. Ireland NSAI...
- Page 20 Table 2 HAR flexible cord Alternative marking utilizing Printed or embossed black-red-yellow thread (Length harmonization marking (May be of color section in mm) Approval organization located on jacket or insulation of internal wiring) Black Yellow Comite Electrotechnique Belge (CEBEC) CEBEC <HAR>...
- Page 21 BX3M-PSLED Alternative marking utilizing Printed or embossed black-red-yellow thread (Length harmonization marking (May be of color section in mm) Approval organization located on jacket or insulation of internal wiring) Black Yellow National Standards Authority of Ireland (NSAI) <NSAI> <HAR> Norges Elektriske Materiellkontroll (NEMKO) NEMKO <HAR>...
- Page 22 MEMO...
- Page 24 Manufactured by Shinjuku Monolith, 2-3-1 Nishi-Shinjuku, Shinjuku-ku, Tokyo 163-0914, Japan Distributed by AX9454 01...