Advertisement
Install the Device/ 设备安装
C Indoor Wall-Mount/ 室内壁装
The indoor wall-mount installation is similar to the surface-mount installation. Install the camera on the wall by
referring to B Surface-Mount.
室内壁装方法与吸顶安装类似，请参见"B 吸顶安装"，将摄像机安装在墙壁上。
D Connect Cables/ 连接线缆
CAUTION/ 注意
• In outdoor installation, a lightning arrester must be installed and the lightning arrester must be grounded.
室外安装时，必须安装避雷器，避雷器必须接地。
•
The strong current cables and weak current cables must be separately laid. The distance between the strong current cable and the weak current cable must be greater than or equal to 5 cm. When connecting cables to the device,
do not connect the strong current cable to the weak current interface to avoid device damages.
强电和弱电必须分开布线，两者间的距离不小于 5cm。线缆与设备连接时，禁止将强电接到弱电接口上，以免造成设备损坏。
• If you have to cut off tail cables that cannot be threaded, reserve the labels on the tail cables. Use insulated rubber tapes and waterproof tapes to wrap all tail cables to prevent short circuit and water leakage. Wrap unused cables
with waterproof tapes to prevent water seepage.
如果尾线因无法穿线而必须剪断时，请保留尾线标签。请务必使用绝缘胶带和防水胶带对所有尾线进行绝缘和防水处理，以免造成短路和漏水。对于不用的线头，需要用防水胶带包住，防止渗水。
Connect the power cable and the ground cable. A bare wire supports the 1.5 mm² (length is less than or equal
1
to 25 m) power cable at most, and a crimping terminal supports the 0.75 mm² (length is less than or equal to
15 m)or 1.0 mm² (length is less than or equal to 20 m) power cable. The ground impedance must be less than
or equal to 5 ohms. Use the OT terminal with an inside diameter of 3 mm.
连接电源线和接地线。接裸线最大支持 1.5mm²（长度最大支持 25m）电源线，配压线端子支持 0.75mm²（长度最大支
持 15m）或 1.0mm²（长度最大支持 20m）电源线。接地线要求阻抗≤
Power cable
电源线
Ground cable
接地线
NOTE/ 说明
When a camera is installed horizontally by default, the surveillance
image is displayed horizontally. Carefully adjust the surveillance
angle when installing the camera to prevent the reverse image
display.
摄像机默认水平安装时，监控画面为水平显示。安装过程中，请注意调整
监控角度，避免安装完成后视频画面翻转。
5Ω，使用内径大小为 3mm 的 OT 端子。
Connect the network cable. Mount the rubber ring of the waterproof connector onto the network cable port
2
and install the remaining components of the waterproof connector in sequence.
连接网线。先将线防水接头部件中的细橡皮圈套在网线接口外，再将剩余部件按如图所示顺序安装。
NOTE/ 说明
Before making an RJ11 plug connector, assemble components of the RJ11 plug connector of the
waterproof connector for network cables in sequence.
在制作水晶头前，请先将网线防水接头的水晶头侧部件按如图所示顺序组装。
O-ring for the waterproof connector
网线防水接头密封圈
Advertisement
