Advertisement
Install the Device/ 设备安装
A Install the SD card/ 安装 SD 卡
Use a
Phillips screwdriver
to remove the
transparent
card.
使用十字螺丝刀将透明罩卸下，插入 SD 卡。
NOTE/ 说明
• When the camera is not connected or cannot be connected to a video surveillance
platform for a long time, you are advised to disable video buffering of the camera
to increase the service life of the SD card.
若摄像机长时间无法接通平台或者不对接平台使用，建议手动关闭摄像机的平台离
线缓存补录功能，以提高SD卡的使用寿命。
• For details, see the Configuration Guide.
详细操作请参见《配置指南》。
Connect the cables to the tails of the camera, perform insulation
3
operations on the cables (see Connect Cables), and put the cables
through the cable entry on the wall. Use the torque of 5 to 7 kgf.cm to
fasten the tapping screws.
将线缆与摄像机的尾线连接，对线缆进行绝缘处理（参见"连接线缆"），然
后塞入墙壁出线孔。使用 5~7Kgf.cm 的扭矩拧紧自攻螺钉。
B Surface-Mount/ 吸顶安装
cover, install the SD
Paste the drilling sticker in the camera installation position and ensure
1
that the center of the sticker overlaps the center of the cable outlet
on the wall. Obtain a drill bit with a 5 mm diameter and drill four 35
mm holes in the specified positions marked by the stickers. Use a claw
hammer to install an expansion bolt into the hole.
将安装定位贴纸贴在摄像机安装位置，贴纸中心请对准墙壁出线孔。依照贴纸
上的标注，选择直径为 5mm 的钻头，钻取深约 35mm 的导孔，并使用羊角
锤将膨胀螺栓打入钻好的孔内。
Use a Phillips screwdriver to loosen screws for fixing the shield, and
4
adjust the angle. Then tighthen the screws.
使用十字螺丝刀将固定内罩的螺丝拧松， 调整监控角度。 调整完毕后， 拧紧螺丝。
NOTE/ 说明
Angles are marked on the chipset of a dome camera. When the 0°
mark is adjusted to the vertical top, the horizontal image is displayed.
When the 90° mark is adjusted to the vertical top, the vertical image
is displayed. In a low-luminance environment (for example, in an
elevator), adjust the 180° mark to the vertical top and avoid blocking
the optical resistor, so that the camera can accurately identify the
ambient luminance.
球型机芯上标识了角度。0°在垂直上方时为水平画面；90°在垂直上方时为
垂直画面；在电梯等亮度偏暗场景下，请将 180°调整至垂直上方，且不遮
挡光敏电阻，以便设备准确识别环境亮度。
Angle mark
角度标识
Use a
Phillips screwdriver
to remove the
2
使用十字螺丝刀将透明罩卸下。
Align the
transparent cover
with the base through the positioning slot,
5
close the
transparent
cover, and use a Phillips screwdriver to tighten
the screws.
通过定位槽将透明罩和底座的位置对齐，合上透明罩并使用十字螺丝刀拧紧螺
钉。
Positioning slot
定位槽
transparent
cover.
Advertisement
