Advertisement
LUBRICATION
NOTE: Because reducer is shipped without oil, it is
necessary to add the proper amount of oil before operating
reducer. Use a high-grade petroleum base rust and oxidation
inhibited (R&O) gear oil – see tables. Follow instructions on
reducer warning tags, and in the installation manual.
Under average industrial operating conditions, the lubricant
should be changed every 2500 hours of operation or every 6
months, whichever occurs first. Drain reducer and flush with
kerosene, clean magnetic drain plug and refill to proper level with
new lubricant.
Case Size
Ratios
Single
TA0107L
Doubles
Single
TA1107H
Doubles
Single
TA2115H
Doubles
Single
TA3203H
Doubles
TA4207H
Single
Doubles
TA5215H
Single
Doubles
TA6307H
Single
Doubles
TA7315H
Single
Doubles
TA8407H
Doubles
TA9415H
Doubles
TA10507H
Doubles
TA12608H
Doubles
Notes:
1. Oil quantity is approximate. Service with lubricant until oil runs out of oil level hole.
2. Below 15 RPM output speed, oil level must be adjusted to reach the highest oil level plug. If reducer position is to vary from those shown in Figure 1, either more or
less oil may be required. Consult Dodge Product Support.
3. Refer to Figure 1 for mounting positions.
Table 2–Oil Volumes by Mounting Position
Horizontal
A (9:00)
B (6:00)
0,6
0,5
0,6
0,5
1,3
0,7
1,3
0,7
2,0
1,2
2,0
1,1
2,7
1,6
2,7
1,4
4,2
2,5
4,2
2,4
7,0
4,7
7,0
4,4
8,3
5,5
8,4
5,2
8,0
11,1
7,9
10,3
7,3
11,1
16,1
15,9
36,0
26,1
50,2
39,3
CAUTION: Too much oil will cause overheating and too little
will result in gear failure. Check oil level regularly. Failure to
observe this precaution could result in bodily injury.
Under extreme operating conditions, such as rapid rise and fall of
temperature, dust, dirt, chemical particles, chemical fumes, or oil
sump temperatures above 90°C, the oil should be changed every
1 to 3 months, depending on severity of conditions.
See Table 2–Oil Volumes for more information.
Oil Volume in Liters
C (3:00)
D (12:00)
0,6
1,3
0,6
1,3
0,6
1,6
0,6
1,6
1,0
2,5
1,0
2,5
1,7
3,9
1,6
3,8
2,8
7,0
2,6
6,9
5,5
12,5
5,2
12,2
6,2
15,3
5,9
15,0
13,2
21,3
12,5
20,9
12,9
23,8
17,1
31,4
24,4
50,6
35,1
66,9
5
Vertical
E (Up )
F (Down)
1,2
1,4
1,2
1,3
1,4
1,8
1,4
1,8
2,2
2,9
2,3
2,8
3,1
4,2
3,3
4,0
6,0
7,3
6,0
7,1
11,0
12,4
10,8
11,9
12,5
15,3
13,1
14,5
20,9
23,7
21,2
21,8
22,7
24,4
31,4
36,5
50,9
53,0
68,3
76,1
MN1620
Advertisement
