Page 4
Use of other accessories may not ensure compliance with FCC RF exposure guidelines. European Conformity Statement Unitech Electronics co., Ltd herewith declares that the Unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive.
Page 6
Waste Electrical and Electronic Equipment (WEEE) Unitech has set up a policy and process to meet the 2012/19/EU concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from Unitech directly or via Unitech’s resellers, you shall either...
Page 8
Laser Information The Unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1. Class II and Class 2 products are not considered to be hazardous. The Unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.
Page 10
It may not be functional anymore. Please only use the original battery from Unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by Unitech’s warranty policy.
Page 12
Unitech product for charging. Please remove the power adapter when the battery is fully recharged. The bundled power adapter that comes with your Unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product.
Page 14
Worldwide Support Unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest Unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan –...
Page 15
The warranty period is varied from each country. Please consult with your supplier or Unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user.
EA630 Plus User’s Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the EA630 Plus gift box. If something is missing or damaged, please contact your Unitech representative. The basic package contents EA630 Plus Terminal ...
Page 30
It takes within 4 hours to charge the terminal with the cradle to full capacity. Connect the type C USB cable to the USB port on EA630 Plus and the other end of the USB cable. Please connect to AC power adapter into the electrical outlet on the USB plug.
Page 31
EA630 Plus User’s Manual 1.4.4 Turning on Terminal for the First Time It is recommended to fully charge EA630 Plus before first use. You can now start up your device to set up the languages, WLAN setting, date and time.
Page 33
EA630 Plus User’s Manual 1.4.6 Inserting the Micro SD/ Nano SIM Card The EA630 Plus has 1 x micro SD and 2 x Nano SIM card slots inside the battery compartment. Note: Before inserting or removing micro SD card or Nano SIM card, please TURN OFF the terminal for the first step.
On the main screen, scroll up the screen to reach the APPS, and Settings and then tap USS (Unitech scan service). Or from the notification bar to tap USS (Unitech scan service). You now enter the Unitech scan service application.
Page 40
EA630 Plus User’s Manual Make sure that both devices are unlocked and have NFC turned on. Also make sure that the NFC antenna area of EA630 Plus and the other phone's NFC area are close to one another. Slightly move the phones until connection is made.
EA630 Plus User’s Manual 2.7 PC Setting Connect EA630 Plus to your computer with the USB type C cable. Your computer will recognize it is USB charging. Slide down from top, the system will show as follow picture, then you can tap on Android System Charging this device via USB.
EA630 Plus User’s Manual 2.11 KeyRemap The EA630 Plus’s keys can be programmed for users to be able to perform different functions or applications. Four options to use key remap functions: Volume_Up, Volume_Down, Programmable Key 1, Scanner Triger Key Left and Scanner Triger Key Right.
On the main screen, scroll the screen from bottom to top to reach the APPS, and tap Settings and then tap USS (Unitech scanner service). Or from the notification bar to tap USS (Unitech scanner service). You now enter the Unitech scan service application.
Page 74
3.1.3 Picklist Mode Picklist mode enables EA630 Plus to decode only barcodes that are aligned under the laser crosshair or LED aiming dot. For picklist mode demonstration, please click on our Youtube channel for more information : https://www.youtube.com/watch?v=QjT2E6hxD_k...
StageGO helps IT admins to swiftly set up a device by just a few barcode scans. Features Swift and effortless device staging for Unitech Android Mobile Devices. Device staging becomes more accessible, time-efficient, and secure. Complete device control at your fingertips.