Advertisement
Quick Links
L o r r y m a d e f r o m P V C
Necessary tools:
Fretsaw
Workshop file
Drills 3, 4 and 13 mm diameter
Countersink bit
Soldering iron and solder
Plastic glue or instant glue
Spanner M4
Hacksaw
Vice with soft jaws
PARTS LIST
PVC square tube
PVC L-profile
Threaded rod
Countersink screws
Nuts
Lock Nuts
Washers
Cable ,red
Cable black
Battery clip
Micro slide switch
Reisistor 180 Ohm
Light Diode , red
Light diode , yellow
Wheels
E114734#1
w i t h L E D l i g h t i n g
Quantity
1
1
1
1
3
1
2
1
1
1
1
1
2
2
6
114.734
The OPITEC range of projects is not intended as play toys for
young children.They are teaching aids for young people
learning the skills of Craft, Design and Technology.These
projects should only be undertaken and tested with the
guidance of a fully qualified adult.
The finished projects are not suitable to give to children
under 3 years old. Some parts can be swallowed. Danger of
Size (mm)
Description
195x40x40x2 Cab, trailer,axle
95x15x15x2 SBumper,switch, fixing
200x3 Axles
16x3 Trailer coupling
M3 M3 coupling
M3 Fixing
7/3,2mm Fixing
500 Wiring
500 Wiring
Battery connection
19x6 On /off switch
Circuit control
ø3 Rear light
ø3 Front light
ø21,5 Wheels
Please Note
suffocation!
Part No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
Advertisement
Related Manuals for Opitec 114.734
Summary of Contents for Opitec 114.734
- Page 1 L E D l i g h t i n g Necessary tools: Please Note Fretsaw The OPITEC range of projects is not intended as play toys for Workshop file young children.They are teaching aids for young people Drills 3, 4 and 13 mm diameter learning the skills of Craft, Design and Technology.These...
- Page 2 INSTRUCTIONS 1. Mark out the parts from the plan (Page 7) on to the PVC plastic section (1) View from above Drill the 13mm hole diameter for the cab window and the holes for the axles (4mm diameter ) and the trailer coupling (3mm diameter ) before ø3mm any sawing any of the other parts.
- Page 3 INSTRUCTIONS 5. Saw the 200mm threaded rod (3) into 55mm sections as shown in the plan .Clean up the saw cuts with a workshop file . 6. Insert a countersunk head machine screw ( 4 ) from under- 7. Thread a wheel (14) on the end of each axle so that they neath through the 3mm hole and wind on 3 nuts ( 5) from are all equally arranged and will rotate easily ! above then contra tighten them in position .
- Page 4 Instructions 11. Drill a ø4mm hole through the centre of part (i) in order 10. Insert the threaded rod (3) as an axle into the axle carrier to feed the cables through. (f ). Add wheels (15) to both sides of the axle (j) as de- scribed in step 7.
- Page 5 Instructions 13. Set the trailer on to the screw (4) as shown. Add a washer (7) from above and fix with a nut (6). 14. Use the switch to switch on the light. Done! 15. If you like you can paint the vehicle as you wish. E114734#1...
- Page 6 E114734#2...
- Page 7 Instructions Templates Scale 1:1 PVC L-profile PVC tube part 1 E114734#1...