Page 1
EQUIPMENT OPERATORS MANUAL TLN250 ORIGINAL LLP FARM MACHINERY GROUP OY LEVYTIE 4 ● 74510 IISALMI PUH. +358 (0) 20 1984 020 ● FAX 020 1984 029...
Page 2
OPERATOR MANUAL D00056EN_A (CE 16116→) ROAD DRAGGER ORIGINAL EY-VAATIMUSTENMUKAISUUSVAKUUTUS TUOTTEESTA LLP Farm Machinery Group Oy vakuuttaa, että markkinoille saatettu kone täyttää direktiivin 2006/42/EY ja standardit SFS-EN ISO 12100 ja SFS-ISO730-1. FÖRSÄKRAN OM ÖVERENSSTÄMMELSE LLP Farm Machinery Group Oy försäkrar härmed till marknader att tillförda maskin uppfyller maskindirektivet 2006/42/EY och standard SFS-EN ISO 12100 och SFS-ISO730-1.
Page 3
Warranty repairs should be done by the FMG service dealer or service dealer appointed by the manufac- turer. • In case the defects shown in reclamation is not valid or if case otherwise is not in the warranty area FMG has right to reject from the compensation. •...
Page 4
Manual require the use of special tools and exact technical data. In case of that kind need please contact your FMG seller or factory. • Use only genuine FMG spare parts for optimum performance from your tractor and road dragger. Spares will be sold through the FMG seller.
OPERATOR MANUAL D00056EN_A (CE 16116→) ROAD DRAGGER 1. SAFETY INSTRUCTIONS This section summarizes the regulations that must always be followed when working with the road dragger. However, these regulations do not exempt the driver from statutory and other national regulations regarding traffic safety and occupational health and safety. Safety regula- tions that apply to different types of working sites and existing road traffic laws must always be observed.
Page 7
OPERATOR MANUAL D00056EN_A (CE 16116→) ROAD DRAGGER WARNING Observe the manufacturer's instructions while working. WARNING Pay attention to other road users. IMPORTANT Always lower the implement and stop the engine before leaving the cab. IMPORTANT Never service or clean an implement that is resting on the hydraulics. Use mechanical support.
Width with extra Number of Weight Attachment to Model Width Length wing blades tractor TLN250 250 cm 290 cm 670 cm 2700 kg* Hitch *Without additional wing and draw bar Sound level is less 70dB (A). 4. INSTRUCTIONS 4.1. Usage area Road dragger has been designed to balance graveled roads and yards, however dragger could be used also to the slush removing.
OPERATOR MANUAL D00056EN_A (CE 16116→) ROAD DRAGGER 4.3. Basic adjustments Height adjustment Adjustment of finalising blade Tilt adjustment Picture 1. Road dragger basic adjustment 5. SERVICE One of the most important things to keep dragger always in a good shape is service done in the correct time.
OPERATOR MANUAL D00056EN_A (CE 16116→) ROAD DRAGGER - Check all the hydraulics and hoses 5.3. Service after 500 hours - Check the wear of the stinger pins - Check the tightness of the screws 5.4. Annual service All above mentioned points. Lubricate all the lubrication points when the season is over.
OPERATOR MANUAL D00056EN_A (CE 16116→) ROAD DRAGGER 5.5. Lubrication points Lubricate grease nipples shown in the picture every week. Clean the top of the grease nipple before lubrication. 5.6. Screws to be tighten Tighten all the screws after the first 10 hours and after that after 500 hours. Check the tightness of the blade daily.
Page 15
OPERATOR MANUAL D00056EN_A (CE 16116→) ROAD DRAGGER Picture 6. Draw bar steering (option) Picture 7. Adjustment of finalising blade from left side (option) Picture 8. Adjustment of finalising blade from right side (option) Page 15...