Related Manuals for FMG AH260MEK
Summary of Contents for FMG AH260MEK
- Page 1 EQUIPMENT OPERATORS MANUAL AH260MEK – AH380MEK ORIGINAL LLP FARM MACHINERY GROUP OY LEVYTIE 4 ● 74510 IISALMI PUH. 020 1984 020 ● FAX 020 1984 029...
- Page 2 OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER ORIGINAL EY-VAATIMUSTENMUKAISUUSVAKUUTUS TUOTTEESTA LLP Farm Machinery Group Oy vakuuttaa, että markkinoille saatettu kone täyttää direktiivin 2006/42/EY ja standardit SFS-EN ISO 12100 ja SFS-ISO730-1. FÖRSÄKRAN OM ÖVERENSSTÄMMELSE LLP Farm Machinery Group Oy försäkrar härmed att tillförda maskin uppfyller maskindirektivet 2006/42/EY och standard SFS-EN ISO 12100 och SFS-ISO730-1.
- Page 3 Losses in income, costs and loosen working hours caused by the defected part is not covered by the warranty. Warranty repairs should be done by the FMG service dealer or service dealer appointed by the manufacturer. In case the defects shown in reclamation is not valid or if case otherwise is not in the warranty area FMG has right to reject from the compensation.
- Page 4 In case of that kind need please contact your FMG seller or factory. Use only genuine FMG spare parts for optimum performance from your tractor and sweeper. Spares will be sold through the FMG seller.
-
Page 5: Table Of Contents
OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER TABLE OF CONTENTS TABLE OF CONTENTS ............................ 5 SAFETY INSTRUCTION ........................... 6 CONSTRUCTION ............................8 TECHNICAL SPECIFICATION ......................... 9 USE OF THE SWEEPER .......................... 9 4.1. Using area............................9 4.2. Instructions............................9 4.3. Working position ..........................10 SERVICE .............................. -
Page 6: Safety Instruction
OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER 1. SAFETY INSTRUCTION This section summarizes the regulations that must always be followed when working with the sweeper. However, these regulations do not exempt the driver from statutory and other national regulations regarding traffic safety and occupational health and safety. Safety regulations that apply to different types of working sites and existing road traffic laws must always be observed. - Page 7 OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER WARNING Observe the Operator Manual instructions while working. WARNING Pay attention to other road users. IMPORTANT Always lower the implement down and stop the engine before leaving the cab. IMPORTANT Never service or clean an implement that is resting on the hydraulics. Use mechanical support.
-
Page 8: Construction
OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER 2. CONSTRUCTION 1. Sweeper disc 2. Sweeper frame 3. Support leg 4. Machine bracket 5. Shock absorber 6. Restricting chain 7. Turning cylinder 8. Gearbox 9. Chain box Page 8... -
Page 9: Technical Specification
Height Working Brush Turning Weight (cm) (cm) width (cm) dia (cm) r/min angle (kg) AH260MEK +/-28 AH300MEK +/-28 AH380MEK 1000 +/-24 1870 AH380Mek requires min. 150 hp from the base machine. 4. USE OF THE SWEEPER 4.1. Using area Mechanical open sweeper is intended for large and small areas and roads cleaning. -
Page 10: Working Position
OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER 4.3. Working position Adjust sweeper that ends of the sweeper lamella meet ground (Picture 1). Too much press in the sweeper lamella leads to over wearing and shorter life time. Picture 1. Adjustment of the sweeper lamella IMPORTANT Always start the brush in the air. -
Page 11: Weekly Service
OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER 5.2. Weekly service - Grease the roller chain of the sweeper every 40 hours, tighten if necessary. Do not over tight. - Grease the sweeper bearings - Grease the turning bar joints and the cylinder pins - Check the hydraulic plugs for leaks 5.3. -
Page 12: Lubrication Points
OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER 5.5. Lubrication points Lubricate nozzles shown in the picture on a weekly basis (Picture 3.) Clean top of the nozzle before lubrication. Page 12... -
Page 13: Screws To Be Tighten
OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER 5.6. Screws to be tighten Tighten all the screws and nuts after the first 10 hours` drive and after that after 500 hours. Page 13... -
Page 14: Tightening Instruction Of Conical Sleeve
OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER 5.7. Tightening instruction of conical sleeve Tighten screws lightly and align the hub. Tighten screws alternately crosswise in two or three stages. The tightening torque is 17 Nm. Tighten screws alternately and evenly until the all screws are tighten properly. Page 14... -
Page 15: Brush Replacement
OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER BRUSH REPLACEMENT 1. Remove the cover out. The sweeper AH300MEK has covers in both sides, that should be removed. 2. Remove the chain, sprocket and sleeve. Page 15... - Page 16 OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER 3. Remove the screws from right (4 pcs) and left (4 pcs) side. Page 16...
- Page 17 OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER Page 17...
- Page 18 OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER 7. Change brush rings. Set brush rings so that studs on rings would be on opposite side alternately. 7. Set brush support at the place. Remember to tighten properly conical sleeve. Page 18...
- Page 19 OPERATORS MANUAL D00011C MECHANICAL OPEN SWEEPER LLP FARM MACHINERY GROUP OY LEVYTIE 4 74510 IISALMI, FINLAND PUH. +358 (0)20 1984 020 FAX +358 (0)20 1984 029 www.fmg.fi Page 19...