Related Manuals for FMG KHL120
Summary of Contents for FMG KHL120
- Page 1 EQUIPMENT OPERATORS MANUAL KHL120 – KHL200 ORIGINAL LLP FARM MACHINERY GROUP OY LEVYTIE 4 ● 74510 IISALMI PUH. 020 1984 020 ● FAX 020 1984 029...
- Page 2 OPERATORS MANUAL D00013C COLLECTING SWEEPER ORIGINAL EY-VAATIMUSTENMUKAISUUSVAKUUTUS TUOTTEESTA LLP Farm Machinery Group Oy vakuuttaa, että markkinoille saatettu kone täyttää direktiivin 2006/42/EY ja standardit SFS-EN ISO 12100 ja SFS-ISO730-1. FÖRSÄKRAN OM ÖVERENSSTÄMMELSE LLP Farm Machinery Group Oy försäkrar härmed att tillförda maskin uppfyller maskindirektivet 2006/42/EY och standard SFS-EN ISO 12100 och SFS-ISO730-1.
- Page 3 Losses in income, costs and loosen working hours caused by the defected part is not covered by the warranty. Warranty repairs should be done by the FMG service dealer or service dealer appointed by the manufacturer. In case the defects shown in reclamation is not valid or if case otherwise is not in the warranty area FMG has right to reject from the compensation.
- Page 4 In case of that kind need please contact your FMG seller or factory. Use only genuine FMG spare parts for optimum performance from your tractor and sweeper. Spares will be sold through the FMG seller.
-
Page 5: Table Of Contents
OPERATORS MANUAL D00013C COLLECTING SWEEPER TABLE OF CONTENTS TABLE OF CONTENTS ............................ 5 SAFETY INSTRUCTIONS ......................... 6 CONSTRUCTION ............................8 SPECIFICATIONS ............................. 9 OPERATING INSTRUCTIONS ......................... 9 MAINTENANCE ............................9 5.1. Daily service............................9 5.2. Weekly service ..........................10 5.3. Service after 500 hours ........................ -
Page 6: Safety Instructions
OPERATORS MANUAL D00013C COLLECTING SWEEPER 1. SAFETY INSTRUCTIONS This section summarizes the regulations that must always be followed when working with the collecting sweeper. However, these regulations do not exempt the driver from statutory and other national regulations regarding traffic safety and occupational health and safety. Safety regulations that apply to different types of working sites and existing road traffic laws must always be observed. - Page 7 OPERATORS MANUAL D00013C COLLECTING SWEEPER WARNING Observe the Operator Manual instructions while working. WARNING Pay attention to other road users. IMPORTANT Always lower the implement down and stop the engine before leaving the cab. IMPORTANT Never service or clean an implement that is resting on the hydraulics. Use mechanical support.
-
Page 8: Construction
OPERATORS MANUAL D00013C COLLECTING SWEEPER 2. CONSTRUCTION 1. Sweeper frame 2. Sweeper 3. Side sweeper 4. Hydraulic cylinder 5. Depth wheel 6. Hydraulic motor 7. Side door cover 8. Attaching frame 9. Water tank Page 8... -
Page 9: Specifications
Model Working width Rubbish tank Weight (kg) Water tank (mm) capacity (l) capacity (l) KHL120 120 (165) KHL160 160 (205) KHL200 200 (245) 4. OPERATING INSTRUCTIONS Before use take care that sweeper is correctly engaged and all the lockings are completely done. -
Page 10: Weekly Service
OPERATORS MANUAL D00013C COLLECTING SWEEPER 5.2. Weekly service - Grease the sweeper bearings - Grease the sweeper fixing sockets - Grease the support wheel bearings - Check the hydraulic plugs for leaks 5.3. Service after 500 hours - Check all the pins - Check the tightness of the screws 5.4. -
Page 11: Lubricating Points
OPERATORS MANUAL D00013C COLLECTING SWEEPER 5.5. Lubricating points Lubricate nozzles shown in the picture. Clean top of the nozzle before lubrication. Page 11... -
Page 12: Screws To Be Tighten
OPERATORS MANUAL D00013C COLLECTING SWEEPER 5.6. Screws to be tighten Tighten all the screws and nuts after the first 10 hours` drive and after that after 500 hours. Page 12... -
Page 13: Electric Valve Cables
OPERATORS MANUAL D00013C COLLECTING SWEEPER 6. ELECTRIC VALVE CABLES Connection for 8/3 valve: Yellow-green→ground 3/31 Blue→supply for valve 1 2/54g Brown→supply for valve 2 Connection for 6/2 valve: Ground 3/31 Supply for valve 1 2/54g Page 13... -
Page 14: Sweeper Lamella Change
OPERATORS MANUAL D00013C COLLECTING SWEEPER 7. SWEEPER LAMELLA CHANGE 1. Remove nuts of side cover (8 pcs) 2. Remove 2 nuts from other side. Page 14... - Page 15 OPERATORS MANUAL D00013C COLLECTING SWEEPER 3. Remove socket cap screws (4pcs) 4. Remove one bolt from other side. Page 15...
- Page 16 OPERATORS MANUAL D00013C COLLECTING SWEEPER 5. Take away pin and put the brush support down. Remove the rubber if needed. 6. Remove bolts from brush support (4pcs). Page 16...
- Page 17 OPERATORS MANUAL D00013C COLLECTING SWEEPER 7. Change sweeper lamella. Take care that steering pins will be mounted to the different sides. Page 17...
- Page 18 OPERATORS MANUAL D00013C COLLECTING SWEEPER LLP FARM MACHINERY GROUP OY LEVYTIE 4 74510 IISALMI, FINLAND PUH. +358 (0)20 1984 020 FAX +358 (0)20 1984 029 www.fmg.fi Page 18...