Related Manuals for FMG PL245
Summary of Contents for FMG PL245
- Page 1 EQUIPMENT OPERATORS MANUAL PL245-PL360 ORIGINAL LLP FARM MACHINERY GROUP OY LEVYTIE 4 ● 74510 IISALMI TEL. +358 (0)20 1984 020 ● FAX +358 (0)20 1984 029...
- Page 2 OPERATORS MANUAL D0005D BULLDOZER BLADE ORIGINAL EY-VAATIMUSTENMUKAISUUSVAKUUTUS TUOTTEESTA LLP Farm Machinery Group Oy vakuuttaa, että markkinoille saatettu kone täyttää direktiivin 2006/42/EY ja standardit SFS-EN ISO 12100 ja SFS-ISO730-1. FÖRSÄKRAN OM ÖVERENSSTÄMMELSE LLP Farm Machinery Group Oy försäkrar härmed att tillförda maskin uppfyller maskindirektivet 2006/42/EY och standard SFS-EN ISO 12100 och SFS-ISO730-1.
- Page 3 Losses in income, costs and loosen working hours caused by the defected part is not covered by the warranty. Warranty repairs should be done by the FMG service dealer or service dealer appointed by the manufacturer. In case the defects shown in reclamation is not valid or if case otherwise is not in the warranty area FMG has right to reject from the compensation.
- Page 4 In case of that kind need please contact your FMG seller or factory. Use only genuine FMG spare parts for optimum performance from your tractor and bulldozer blade. Spares will be sold through the FMG seller.
-
Page 5: Table Of Contents
OPERATORS MANUAL D0005D BULLDOZER BLADE T ABLE OF CONTENTS TABLE OF CONTENTS ............................ 5 SAFETY INSTRUCTIONS ......................... 6 CONSTRUCTION ............................8 TECHNICAL SPECIFICATIONS ....................... 9 BULLDOZED BLADE USE ........................9 4.1. Using area ............................9 4.2. Instruction ............................9 4.3. Bulldozer blade use ........................... -
Page 6: Safety Instructions
OPERATORS MANUAL D0005D BULLDOZER BLADE 1. SAFETY INSTRUCTIONS This section summarizes the regulations that must always be followed when working with the bulldozer blade. However, these regulations do not exempt the driver from statutory and other national regulations regarding traffic safety and occupational health and safety. Safety regulations that apply to different types of working sites and existing road traffic laws must always be observed. - Page 7 OPERATORS MANUAL D0005D BULLDOZER BLADE WARNING Observe the Operators Manual instructions while working. WARNING Pay attention to other road users IMPORTANT Always lower the implement down and stop the engine before leaving the cab. IMPORTANT Never service or clean an implement that is resting on the hydraulics. Use mechanical support.
-
Page 8: Construction
OPERATORS MANUAL D0005D BULLDOZER BLADE C ONSTRUCTION 1. Machine bracket 2. Floating bar 3. Turning cylinder 4. Releasing device 5. Main wing 6. Supporting leg 7. Blade 8. Led-daytime running light (Option) Page 8... -
Page 9: Technical Specifications
OPERATORS MANUAL D0005D BULLDOZER BLADE 3. TECHNICAL SPECIFICATIONS Model Width (cm) Height (cm) Working width (cm) Weight (kg) Blade angle PL245 173 - 245 41/45 PL275 195 - 275 41/45 PL300 216 - 305 41/45 PL330 237 - 335 41/45... -
Page 10: Bulldozer Blade Use
OPERATORS MANUAL D0005D BULLDOZER BLADE 4.3. Bulldozer blade use Engage bulldozer blade to the working machine that floating bar is in the mid position and bulldozer blade is in the balanced position (Picture 1). Picture 1. Floating bar in the mid position In case the adapter is wrong change adapter and ensure that screws are tightened well. - Page 11 OPERATORS MANUAL D0005D BULLDOZER BLADE Picture 2. Plough frame in the upright position Blade angle is possible to adjust by moving releasing device to another hole (3 different alternative) (Picture 3). Page 11...
-
Page 12: Service
OPERATORS MANUAL D0005D BULLDOZER BLADE Picture 3. Three holes for the releasing device 5. SERVICE The most important thing to get maximum reliability is good service in time. Service costs are smaller compared to the repairing´s costs. Below mentioned service includes all the lubrications and adjustments. -
Page 13: Lubricating Point
OPERATORS MANUAL D0005D BULLDOZER BLADE Lubricate also piston rods when leaving equipment to the storage place. 5.5. Lubricating point Lubricate nipples shown in the picture (Picture 4). Clean the top of the nipple before lubrication. Picture 4. Lubrication Page 13... -
Page 14: Screws To Be Tighten
OPERATORS MANUAL D0005D BULLDOZER BLADE 5.6. Screws to be tighten Tighten all the screws after 10 hours´ drive and after that between 500 working hours. Check the knife fixing screw daily. 1. Tightening screws of the cylinders 2. Tightening nut of the main pin in the center 3. - Page 15 OPERATORS MANUAL D0005D BULLDOZER BLADE LLP FARM MACHINERY GROUP OY LEVYTIE 4 74510 IISALMI, FINLAND PUH. +358 (0)20 1984 020 FAX +358 (0)20 1984 029 www.fmg.fi Page 15...