Subscribe to Our Youtube Channel
Related Manuals for USX-MOUNT XMS004-M-1
Summary of Contents for USX-MOUNT XMS004-M-1
- Page 1 XMS004-M-1 INSTRUCTION MANUAL For 13-32" TV If you have any questions along the way, just give us a call 1-800-460-0956 or mail to customerservice@x-mount.com. We’re ready to help!
- Page 2 Before getting started, let’s check below lists to make sure it is just right for you! MAX:200mm/7.87" (MIN:75mm/2.95") Check your TV VESA is within No? This mount is NOT compatible. Min and Max size MAX:200mm/7.87" (MIN:75mm/2.95") Yes? Perfect ! CAUTION: DO NOT exceed the maximum weight Does your TV No? Perfect –...
- Page 3 TV INTERFACE MAX:200mm[7.87in] MIN:75mm[2.95in] MAX:200mm [2.95in] MIN: 75mm [2.95in] WALL PLATE TOP VIEW - EXTENDED SIDE VIEW - RETRACTED Ø8mm [Ø0.31in] +5° 120mm 100mm [4.72in] [3.94in] 280mm [11.02in] -15° 51mm [2.01in] FULLY ASSEMBLED MOUNT TOP VIEW - RETRACTED TOP VIEW - EXTENDED 233mm [9.19in] 233mm...
- Page 4 WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
- Page 5 Parts and Hardware for STEP 2 Lag Bolt M6x8mm Bolt Allen Key Contact us at telephone 1-800-460-0956 (USA) or mail to customerservice@x-mount.com. to have Velcro x3 Concrete Wall Anchor these additional pieces shipped directly to you. 2pcs 1-1 Disassemble Wall Plate Unit into Two Pieces Wall plate ①...
- Page 6 1-2 Assembly Extenders and TV plate Please pay attention to the front and back of the extenders while installing. Front Back...
- Page 7 1-3 Choose Configuration If your TV VESA size is above 100*100mm, you need to assemble extended arms onto TV plate using bolts and alley key per below option 2 - option 4 shown. Option 1 Option 3 ② ② ④ ④...
- Page 8 1-4 Select TV Screws...
- Page 9 1-5 Need Spacer? 1-6 Attach the TV Plate No, choose suitable screws and washers. VESA ≤ 100mm x 100mm Yes, choose suitable screws, washers and spacers. Tips: If you need to combine M6/M8(e/f/g) screws with 2.5mm spacers( i ), you have to remove the inner circle. 100mm x 100mm <...
- Page 10 CAUTION: Avoid potential personal injury or property damage! ● Drywall covering the wall, must not exceed 5/8 in. (16 mm) ● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm) ●...
- Page 11 3. Drill pilot holes using a 1/8 in. (3.2 mm) diameter drill bit. IMPORTANT: Pilot holes must be drilled to a depth of 2.16 in. (55 mm). Be sure to drill into the center of the studs. 4. Install wall plate using lag bolts .
- Page 12 CAUTION: Avoid potential personal injury or property damage! ● Mount the wall plate assembly directly onto the concrete surface ● Minimum solid concrete thickness: 8 in. (203 mm) 1. Position the wall plate on the wall at your desired height. Level the wall plate and mark the hole locations.
- Page 13 3. Insert anchors. CAUTION: Be sure the anchors are seated flush with the concrete surface. 4. Insert wall plate using lag bolts . Tighten the lag bolts only until they are pulled firmly against the wall plate. CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
- Page 14 Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall tightly.
- Page 15 and fix them using screws ① fully. Hang pre-assembled TV unit on the wall plate ① Wall plate...
- Page 16 ① ① 5-1 Loosen 2 bolts at the same time to tilt TV (+5°/-15°) to desired angle. Fasten fully 2 bolts when finished. +5° ① +5° -15° -15° ①...
- Page 17 Cables manage: Manage TV cables orderly and guide them through the velcros. Velcro...
Need help?
Do you have a question about the XMS004-M-1 and is the answer not in the manual?
Questions and answers