Table of Contents
Advertisement
OTHER FUNCTIONS
MULTI ROOM SELECTOR
The Multi Room Selector is a function which allows you to listen to the
same or a different source in a room other than the room in which the
SR-14EX is located. To use this function, a multi room remote unit and
remote control signal receiver available from your Marantz dealer are
necessary. The operations possible with the multi room function are
explained briefly below. For details, refer to the instruction manual
supplied with the multi room remote control unit and receiver.
MULTI ROOM SELECTOR OPERATION
Press the MULTI button !9 . The unit enters multi room mode and
1.
the display indicates "SELCT SOURCE" and flashes the "MULTI"
indicator for approx. 10 seconds. In this time, you can select the
input source by turning the INPUT SELECTOR knob !5 .
Then, the display indicates "MULTI VOL" "VOLUME xx dB" for
2.
approx. 5 seconds. During this time, you can set the volume level
for the multi room operation. This will only set the volume in the
second room.
MULTI ROOM SELECTOR OPERATION (USING THE MULTI
ROOM REMOTE CONTROL UNIT)
1.
Press the M.R. on button on page of Input mode, the POWER
ON button, or select the desired source on multi room remote
control unit from the second room. Any of these operations will
put the SR-14EX into multi room mode and "MULTI" will light in
the display.
2.
Press the VOLUME + or VOLUME – button on the multi room
remote control unit to set the desired sound volume.
3.
In multi room mode, the multi room remote control unit can be
used in the multi room to operate the following functions.
You can select a tuner preset channel and tuning up or down,
and direct frequency selection. And you can control the CD
player LD player, DVD player and other source connected to the
SR-14EX.
Caution:
• Multi room mode can only be selected when the SR-14EX
POWER switch q is turned on.
• If the main room is active (not standby mode), you cannot select
a radio band except the band of the main room. For example; if
the FM band is selected in the main room, you cannot select the
AM band in the multi room.
• The operating procedure for this is the same as the Multi-room
operations using the remote unit.
• If you operate from second room, SR-14EX will output video
signal with OSD information.
M
U L T
I
V D E O
I
A U
D I
O
V O L U M E L
E E
S
L E
E P T I
M E R
– – –
M A
I
N
–
R
V
I D E O
A U D I O
DIALOGUE NORMALIZATION MESSAGE
Dialogue Normalization (Dial Norm) is a feature of Dolby Digital.
When playing back software which has been encoded in Dolby
Digital, sometimes you may see a brief message in the front panel
display which will read "Dial Norm X dB" (X being a numeric value).
Dialogue Normalization serves to let you know if the source material
has been recorded at a higher or lower level than usual. For example,
if you see the following message: "Dial Norm + 4 dB" in the front panel
display, to keep the overall output level constant just turn down the
volume control by 4 dB. In other words, the source material that you
are listening to has been recorded 4 dB louder than usual.
If you do not see a message or see "Dial Norm 0 dB" in the front panel
display, then no adjustment of the volume control is necessary.
R
O O
M
S
E U
T P
:
D
V
D
:
D
V
D
:
V
L
–
7 5
d B
:
V A
R
I A B
L
E
:
9 0 m i n
OO
M
S
T T
A
U
S
– – –
:
L D
:
L D
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the TV IN jack to
control the power (ON/OFF) to the SR-14EX.
AUTO POWER ON
1.
Be sure TV auto mode is on. (Refer page 18 : System Setup 1/2 )
2.
Connect your TV TUNER (etc) to the TV IN terminal.
Be sure to connect the video input.
3.
Turn OFF the power to the TV TUNER and the SR-14EX.
4.
Turn ON the TV TUNER and tune in a receivable station.
5.
When the station is received, the SR-14EX turns ON and TV is
selected automatically.
AUTO POWER OFF
1.
In the above situation, turn the TV TUNER OFF or select a channel
that does not contain any broadcast.
2.
The power to the SR-14EX switches to STANDBY after approx. 5
minutes.
Note:
• AUTO POWER OFF is canceled if the INPUT SELECTOR knob
!5 is set to a source other than TV. The function reactivates
when TV is selected again.
Caution:
• Some TV broadcasts may cause the TV AUTO FUNCTION to turn
ON. To set this function ON/OFF, refer to the SETUP MENU.
SETTING THE SLEEP TIMER (ONLY REMOTE
CONTROL UNIT)
Set the sleep timer while the power is turned on.
1.
Turn the power ON and press the Sleep button on page of
Control mode.
"SLEEP" blinks on the display.
2.
Press the Sleep button the number of times to set the desired
sleep time.
Each press of the Sleep button changes the display in the
following order:
10
20
OFF
90
"SLEEP" stops blinking and lights steadily.
* While the sleep timer is activated, the remaining time can be
displayed for approx. 2 seconds by pressing the Sleep button.
* To cancel the sleep timer, press the Sleep button and then press
the Clear button.
This operating procedure is same as the Multi room operations from
second room.
22
30
40
50
80
70
60
Hide quick links:
Advertisement
Table of Contents
