Makita KP001G Instruction Manual page 21

3. Draw a cutting line on the workpiece and align the
blade edge with the cutting line.
► Fig.37: 1. Blade edge 2. Cutting line 3. Depth guide
4. Thumb screw
NOTE: Make sure that the blade edge comes out
of the side end of the drum by 1.6 mm – 1.8 mm for
shiplapping. (See "A" in the following figure.)
* You can opt to let the blade end come out of the
side end of the front base by 0.2 mm - 0.4 mm.
(See "B" in the following figure.)
► Fig.38: 1. Blade edge 2. Side end of drum 3. Side
end of front base
4.
Slide the edge fence in the guide rule inwards until
it comes in contact with the side wall of the workpiece.
Then secure it in place with the thumb screw.
► Fig.39: 1. Guide rule 2. Edge fence 3. Side wall
4. Thumb screw
5. Perform planning operation by moving the tool
with the whole edge fence sliding along the side wall of
the workpiece.
NOTE: Reaching lengths of the guide fence can be
extended by attaching an extra piece of wood to the
attachment holes in the guide fence.
► Fig.40: 1. Extra piece of wood 2. Attachment holes
Chamfering
► Fig.41
Use the "V" grooves cut in the front base to make a
chamfering cut as shown in the figure.
Perform planning operation by moving the tool aligning
one of the three "V" grooves in the front base with the
corner edge of the workpiece.
► Fig.42: 1. V groove for medium chamfers 2. V
groove for small chamfers 3. V groove for
large chamfers
Using chamfering rules
Optional accessory
1. Slide the edge fences in the chamfering rules
inwards until they come in contact with the corner walls
of the workpiece.
2. Secure the edge fences in place with the thumb
screws.
3.
Perform planning operation by moving the tool
with the whole edge fences sliding along the corner
walls of the workpiece.
► Fig.43: 1. Chamfering rule 2. Edge fences
3. Thumb screw
NOTE: For large chamfers, make many passes of
planning, starting from small chamfering to larger
chamfering, as shown in the figure.
► Fig.44: 1. Edge fences 2. Small chamfering
3. Large chamfering
WIRELESS ACTIVATION
FUNCTION
What you can do with the wireless
activation function
The wireless activation function enables clean and com-
fortable operation. By connecting a supported vacuum
cleaner to the tool, you can run the vacuum cleaner
automatically along with the switch operation of the tool.
► Fig.45
To use the wireless activation function, prepare follow-
ing items:
• A wireless unit (optional accessory)
• A vacuum cleaner which supports the wireless
activation function
The overview of the wireless activation function
setting is as follows. Refer to each section for detail
procedures.
1.
Installing the wireless unit
2.
Tool registration for the vacuum cleaner
3. Starting the wireless activation function
Installing the wireless unit
Optional accessory
CAUTION:
Place the tool on a flat and stable
surface when installing the wireless unit.
NOTICE:
Clean the dust and dirt on the tool
before installing the wireless unit. Dust or dirt
may cause malfunction if it comes into the slot of the
wireless unit.
NOTICE:
To prevent the malfunction caused by
static, touch a static discharging material, such
as a metal part of the tool, before picking up the
wireless unit.
NOTICE:
When installing the wireless unit,
always be sure that the wireless unit is inserted
in the correct direction and the lid is completely
closed.
1. Open the lid on the tool as shown in the figure.
► Fig.46: 1. Lid
2. Insert the wireless unit to the slot and then close
the lid.
When inserting the wireless unit, align the projections
with the recessed portions on the slot.
► Fig.47: 1. Wireless unit 2. Projection 3. Lid
4. Recessed portion
When removing the wireless unit, open the lid slowly.
The hooks on the back of the lid will lift the wireless unit
as you pull up the lid.
► Fig.48: 1. Wireless unit 2. Hook 3. Lid
After removing the wireless unit, keep it in the supplied
case or a static-free container.
21 ENGLISH