Table of Contents
Advertisement
Quick Links
自动门襟锁眼机
Button Holing Indexer
（MB6003B-JUKI-LBH1790ANS-AAP）
使用说明书
Instruction Manual
常州智谷机电科技有限公司
CHANGZHOU WISDOM & VALLEY ELECTRICAL TECHNOLOGY CO.,LTD
在使用本设备之前请先阅读本使用说明书.
Please read the operation manual of the touch
screen interface before using the device
版本信息/ Version
请将本使用说明书放在便于查阅的地方保管
2022.04.03
Please keep this operation manual of touch screen
interface in convenient place for reference
Advertisement
Table of Contents
Related Manuals for IMB MB6003B-JUKI-LBH1790ANS-AAP
Summary of Contents for IMB MB6003B-JUKI-LBH1790ANS-AAP
- Page 1 自动门襟锁眼机 Button Holing Indexer （MB6003B-JUKI-LBH1790ANS-AAP） 使用说明书 Instruction Manual 常州智谷机电科技有限公司 CHANGZHOU WISDOM & VALLEY ELECTRICAL TECHNOLOGY CO.,LTD 在使用本设备之前请先阅读本使用说明书. Please read the operation manual of the touch screen interface before using the device 版本信息/ Version 请将本使用说明书放在便于查阅的地方保管 2022.04.03 Please keep this operation manual of touch screen...
- Page 2 感谢购买 IMB 工业用缝纫机。 在使用此机器之前，请仔细阅读以下的说明，这样可以更好地帮到您了解此机器的相关 操作。 这些说明是根据现行的条例明确阐述了正确的工作方法。 Thank you for purchasing this industrial sewing machine from IMB Before using this automatic unit, please read the following instructions, which will help you to understand how the machine operates. These instructions illustrate the correct working methods to comply with current regulations.
- Page 3 ENGLISH...
-
Page 4: Table Of Contents
catalog 1、 Basic information of the equipment....................1 2、 Technical parameters of the equipment..................2 3、Safety precautions..........................3 4. key function description........................5 5、Operating instructions......................... 6 5.1. Preparation before operation....................6 5.2. Operation process description....................6 6、 Adjustment instructions........................11 6.1 Ajustment of the lapel card piece....................11 7、... -
Page 5: 1、Basic Information Of The Equipment
1、Basic information of the equipment 1 ： JUKI-LBH1790ANS-AAP ； 2：Emergency stop button； 3：Locating mechanism； 4：Rac k and table；5：Operation table； 6：Control box； 7：Knee switch； 8：Air blower； 9： Power switch；10 ：Receive mechanism； 11 ：Feed mechanism； 12：Touch screen； 13：L BH1790Adisplay screen... -
Page 6: 2、Technical Parameters Of The Equipment
2、Technical parameters of the equipment MB6003A Button holing indexer Machine head JUKI 1790A Maximum sewing speed 1790A: 3600 /rpm Buttonhole length /mm ≤25 Notch size /mm（inch） 6.4~19.1（1/4~3/4） Presser foot lifting ≤14 height/mm Needle/mm DPX5#11J-#14J Buttonhole interval /mm ≤610 Maximum conveying distance ≤610 Width of fabric /mm 220-420... -
Page 7: 3、Safety Precautions
3、Safety precautions Considerations for safe use of automata 1. In order to prevent accidents caused by electric shock, please do not open the cover of the electrical box of the motor or touch the parts in the electrical box when the power is connected. - Page 8 1. In order to prevent personal injury, please do not operate the machine in the state of removing the belt guard, finger protector and other safety devices. 2. In order to avoid being involved in the machine's personal accident, please do not let your fingers, hair, clothes near the pulley, v-belt, motor, and do not put items on it during the operation of the sewing machine.
-
Page 9: Key Function Description
√ improper operation of the machine may cause personal injury. Please read this instruction carefully and operate correctly before operation. √Please ventilate the machine before it is officially powered on. √ do not turn on the internal parts of the electric cabinet or touch screen while the power is on. -
Page 10: 5、Operating Instructions
（1）Power button: power switch, press the button, the equipment is powered on and ventilated. （2）Knee switch：touch the switch--start sewing, autostop at the end of running （3）Emergency stop button: in emergency state, press the button to stop the machine. Cancel:rotate the emergency stop button to the right hand dorection. - Page 11 5.2.2. Startup picture You can select Chinese or English interface. 5.2.3 Reset presser foot After the default "Chinese", the touch screen jumps to the following picture: The presser foot of the sewing machine does not reset and alarms. Then you can press on the LBH1790A display "Reset" icon and the press foot is reset.
- Page 12 5.2.4 Interface after resetting the presser foot A.Check the amount of "shuttle surplus" in this interface to ensure that a complete processing of a lapel B.Click the "zero clearing" icon to reset the number of items...
- Page 13 5.2.5 Set the formula Click the shirt icon and the following recipe setting interface will appear. Select/set the required recipe in this interface: Click the "+/-" icon to select the formula parameters that have been set. The content displayed below the icon (this area shows how many eyes there are and the distance between each eye) and the display data of "flap width/pre-collected length"...
- Page 14 5.2.6 Cloth placement Cloth should be placed as below picture shows: Requirements:1.The edge of the lapel should be attached to the suction 2.Check whether the lapel card is hooked on the lapel. If the position is not appropriate, please refer to "6.1 Adjustment of lapel card position".
-
Page 15: 6、Adjustment Instructions
5.2.8 Turn off the machine After the operation is completed, please rotate power switch to OFF position and the device is turned off. 6、Adjustment instructions 6.1 Ajustment of the lapel card piece... -
Page 16: 7、Unusual Problems Handling
1.Lapel 2.lapel card piece 3.suction box 4.screw The adjustment method: Step 1: Put the lapel below the entry lapel card and align with the suction box Step 2: Loosen the screw Step 3: Hook the flap card around the flap as shown in the picture above Step 4: Tighten the screws 7、Unusual problems handling 7.1 Broken stiching... -
Page 17: Eye Hole Repairing
Step 3: Click the "Back" icon on the touch screen Step 4: a. If the lapel of "broken wire" is scrapped, click the large "Reset" icon to make a new lapel b. If sewing continues on the original lapel, click the switch with your knee to continue sewing 7.2 Eye hole repairing Single eye repairing method:... -
Page 18: Recondition
Step 4: Draw the line on the flap where the eyes need to be filled as shown in the picture below Step 5: A, put the lapel where needed to fill the eye under the foot of the press B, the edge line of the lapel against the suction box C, scribed line shuold be aligned with the needle Step 6: Click the icon of "Press Foot Down"... - Page 19 Step 4: Move the "single head moving patch" and "single head thin patch" forward out of the space needed to flip the head, as shown in the figure above Step 5: Turn the "Display screen" right as shown in the picture below DISPLAY SCREEN...
-
Page 20: Input/Output Test Interface
Step 6: turn over the machine head to begin recondition 8. Input/output test interface Click the "Input/Output Test" icon in the "Menu Interface" to display the following interface:... -
Page 21: Input Test
8.1 Input test A. In9: For the detection of the origin optical eye of the "feeding mechanism" (refer to the parts manual for the specific position), insert a sheet into the optical eye. If the IN9 display block changes from gray to blue, the input is normal. B. - Page 22 B.Receiveing pallet: After clicking, the display block changes from gray to blue, and the receiving splint rotates to the right as shown in the figure below, indicating that this output is normal. Receiving pushing rod:After clicking, the display block changes from gray to blue, and the feeding push rod moves upward as shown in the figure below, indicating that this output is normal.
-
Page 23: 9、Schematic Diagram
D.Suction operation: after clicking, the display block changes from gray to blue. When the fan starts to work, it means that the output is normal. Blowing: Click and the display block will change from gray to blue. When the air duct of receiving and blowing starts to blow, it means that the output is normal. -
Page 25: Gas Path Schematic Diagram
9.2 Gas path schematic diagram... -
Page 26: 10、Daily Maintenance Requirements
10、Daily maintenance requirements... -
Page 27: 11、Knowledge Product Protection Declaration
The amount of head oil shall √ The head oil not be lower than the warning line Cooling fan operates √ Control box normally, dust is cleaned promptly 11、Knowledge product protection declaration MB6003B-JUKI-LBH1790ANS-AAP is designed by Changzhou wisdom & valley Electric... - Page 28 Technology Co., Ltd.。The intellectual property rights of this achievement belong to Changzhou wisdom & valley Electric Technology Co., Ltd. and are protected by national intellectual property laws and regulations. Without the written permission of the right holder, the patented technology of the achievement shall not be implemented, and the information related to the achievement shall not be copied, sold or disseminated through the network.
Need help?
Do you have a question about the MB6003B-JUKI-LBH1790ANS-AAP and is the answer not in the manual?
Questions and answers