Wheel Torque Specification It is an extremely important safety procedure to apply and Torque Torque Wheel Nut / Bolt maintain proper wheel mounting torque on your trailer axle. Lubricated Size Torque wrenches are the best method to assure the proper lbs-ft lbs-ft amount of torque is being applied to a fastener.
Assembly Safety This Safety Alert Symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! The Safety Alert symbol identifies important safety messages on the snow blade and in the manual. When you see this symbol, read and understand the message, be alert to the potential hazard in the message.
Bolt Torque Table These tables are offered as the suggested maximum torque values for dry (not lubricated) threaded products and are only a general guide. Check tightness of bolts periodically, replace hardware with the same strength bolt. Torque specification for bolts are identified by their head markings as shown. See the “Wheel Torque Specification”...
Label Layout CHC Series CHC25, CHC30, CHC36 Product labels and Serial Plate Product labels and serial plate locations on the equipment are shown in the illustrations below. The CHC label locations are similar for all models, unless otherwise indicated. Manufactured by HORST WELDING MODEL NO.
Retro-reflective Strip Location mile/h IL00009 Retroreflective Tape ASTM D-4956 compliant. 2.0” wide, 9.0” strips. Red x 2 all models Rear all CHC Yellow x 9 CHC 25 Yellow x 9 CHC30 Yellow x 10 CHC36...
Safety Label Layout Safety signs and locations on the equipment are shown in the illustrations below. The CHCFE45 is illustrated however label locations are similar for all models, unless otherwise indicated. Good safety practice requires that you familiarize yourself with the label and the safety message it is delivering. Be aware of the equipment or particular equipment feature that requires your SAFETY AWARENESS.
Page 9
Safety Labels Safety labeling is an important part of the overall safe use of the implement. Safety labeling alerts and warns against potential injury or death, and is important to follow these points to help keep your implement safe for you and others who may be using it.
Assembly This assembly manual is for CHC25, 30, 36 Header Wagon models. The CHC30 is used as an example in the illustrations but generally applies to all header wagon models. Model specific instructions are identified in the manual. The machine is shipped from the factory in a partially disassembled configuration and attached to a pallet that provides easy moving and handling.
STEP 2 Mount Tongue Assembly: CAUTION 1. Remove the 7/8” x 8” hex bolt from the tongue bracket assembly, Heavy or bulky parts 1. Position the tongue on the bracket assembly, and from the left side Prevent potential strain injury, use ap- of the tongue bracket, insert the hex bolt.
STEP 3 Diagonal Channels CAUTION 1. Pin the vertical adjuster brackets to right cast bushing Operational Hazard on top of the axle using 5/8" draw pin, repeat for the Chock wheels while remaining adjuster. assembling the wagon to prevent unwanted SNL00002 movement.
3/4" x 2" hex bolts & lock-nuts (assembled rail should have approx. 2" crown). Note: CHC25 & 30 is a 4.0 x 4.0 one piece top rail. 2� All: With a helper, carefully set the top rail on the rail mounts, place evenly spaced on the diagonal channels from front to back.
STEP 5 Outer mount Ratchet Strap 1. Set the ratchet outer mount on the bottom rail at the preferred location 2. Set and hold the inner bracket in place and secure with four 1/2” x 1 1/2” hex bolts and lock-nuts. Inner bracket 3.
Accessories Tongue Spring Balancer Kits Assembly This instruction sheet applies to: WA-SBD Double Spring Balancer Assembly WA-SB Single Spring Balancer Assembly CAUTION This Safety Alert symbol means Operational Hazard ATTENTION! BECOME ALERT! YOUR SAFETY IS Personal Protection Equipment INVOLVED! (PPE) is required while working in and around this machine.
LK Series Road Signal Kit This instruction sheet applies to: LK18 Road Signal Light Kit (18’ wheelbase - CHC25, CHC30 LK24 Road Signal Light Kit (24’ wheelbase - CHC36) Light Bracket Top Plate The instructions generally apply to all LK signal kits and CHC header wagon models.
CHCLPOP Universal Pad kit This Safety Alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! The Safety Alert symbol identifies important safety messages in this instruction, as well as on the machine and in the operators manual. When you see this symbol, be alert to any hazards and the possibility of personal injury.
HBAFK Honey Bee AirFLEX ® Pad Adapter Kit This Safety Alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! The Safety Alert symbol identifies important safety messages in this instruction, as well as on the machine and in the operators manual. When you see this symbol, be alert to any hazards and the possibility of personal injury.