Table of Contents
Advertisement
Quick Links
Assembly
and Reference Book
SWATHER HEADER WAGON
CAUTION
!
Operational Hazard
Personal Protection Equipment
(PPE)
is
required
assembly.
Please review and understand the assembly manual
before attempting to assemble this machinery.
before attempting to assemble this machinery.
Rev 300320
SHCF36, SHCF45
HORST WELDING
8082 Rd 129 Listowel, ON N4W 3G8 Canada
519-291-4162
1-866-567-4162
Fax 1-519-291-5388
sales@horstwelding.com
during
SNL00001
d understand the assembly manual
PRINTED IN CANADA
www.horstwelding.com
!
CAUTION
!
Operational Hazard
Machine assembly should be done by
qualified personnel only.
HWA00109 SHCF
Advertisement
Table of Contents
Related Manuals for Horst Welding CONTOUR SHCF36
Summary of Contents for Horst Welding CONTOUR SHCF36
- Page 1 Assembly and Reference Book SWATHER HEADER WAGON SHCF36, SHCF45 HORST WELDING 8082 Rd 129 Listowel, ON N4W 3G8 Canada 519-291-4162 1-866-567-4162 Fax 1-519-291-5388 sales@horstwelding.com www.horstwelding.com CAUTION CAUTION Operational Hazard Operational Hazard Personal Protection Equipment Machine assembly should be done by...
-
Page 2: Table Of Contents
Table of Contents Assembly Safety � � � � � � � � � � � � � � � � � � � � � � � 3 Chassis Parts ......10 Assembly �... -
Page 3: Assembly Safety
Wheel Torque Specification It is an extremely important safety procedure to apply and Torque Torque Wheel Nut / Bolt maintain proper wheel mounting torque on your trailer axle. Lubricated Size Torque wrenches are the best method to assure the proper lbs-ft lbs-ft amount of torque is being applied to a fastener. - Page 4 Assembly Safety This Safety Alert Symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! The Safety Alert symbol identifies important safety messages on the snow blade and in the manual. When you see this symbol, read and understand the message, be alert to the potential hazard in the message.
-
Page 5: Bolt Torque Table
Bolt Torque Table These tables are offered as the suggested maximum torque values for dry (not lubricated) threaded products and are only a general guide. Check tightness of bolts periodically, replace hardware with the same strength bolt. Torque specification for bolts are identified by their head markings as shown. See the “Wheel Torque Specification”... -
Page 6: Label Layout Shcf Series
Product labels Product labels serial plate with locations on the equipment are shown in the illustrations below. The label locations are similar for all models, unless otherwise indicated. Manufactured by HORST WELDING MODEL NO. SERIAL NO. MADE IN CANADA Rear View... -
Page 7: Safety Label Layout
Safety Label Layout Safety signs and locations on the equipment are shown in the illustrations below. The label locations are similar for all header wagon models, unless otherwise indicated. Good safety practice requires that you familiarize yourself with the label and the safety message it is delivering. Be aware of the equipment or particular equipment feature that requires your SAFETY AWARENESS. -
Page 8: Safety Label Descriptions
Safety Label Descriptions Safety labeling is an important part of the overall safe use of the implement. Safety labeling alerts and warns against potential injury or death, and is important to follow these points to help keep your implement safe for you and others who may be using it. -
Page 9: Parts
Parts Check for missing or damaged parts� Contact the shipping company if damage is found� For missing parts contact your dealer Hardware Bag Description Qty Used in Model Description Qty Used in Model Description Qty Used in Model #10 x 5/8 socket head CHCFSP36 / 45 1/2 x 4 x 7 1/2 u-bolts CHCFSP36 / 45... -
Page 10: Chassis Parts
Chassis Parts Qty Description Used.In.Model 25 2 Swather Top Rail 36' (4" x 4" x .188 HSS) Split SHCF36 26 2 Swather Top Rail 45' (4" x 4" x .188 HSS) Split SHCF45 27 1 Main Tongue Assembly 28 1 CHCF Complete Rear Axle 29 1 CHCF Complete Front Axle... -
Page 11: Assembly
Assembly This assembly manual is for SHCF series Header Wagon models. The example in the illustrations generally applies to all header wagon models. Model specific instructions are identified in the manual. The machine is shipped from the factory in a partially disassembled configuration and attached to a pallet that provides easy moving and handling. -
Page 12: Step 2
STEP 2 Joiner Tie Rod, 3. At each end assemble and tighten with castle nut and 1. Insert rear tie rod end from top side through tapered secure with a cotter pin. bushings in steering plate. 2. Insert front tie rod end from top side through tapered bushings in the tongue bracket. -
Page 13: Step 3
STEP 3 CAUTION Tongue Assembly: Operational Hazard Chock wheels while 1. Remove the 1 1/8” x 10 3/8” hex bolt from the tongue bracket assembly, assembling the wagon 1. Position the tongue on the bracket assembly, and from the left side of the to prevent unwanted tongue bracket, insert the hex bolt. -
Page 14: Step 4
STEP 4 Riser Plates CAUTION 1. Pin the adjuster bracket to right cast bushing on top Operational Hazard of the axle using 5/8" x 7.0” draw pin, repeat for the Chock wheels while remaining bracket. assembling the wagon to prevent unwanted SNL00002 movement. -
Page 15: Step 5
STEP 5 Top Rail 1. Mate the bolt flanges on the 4.0” x 4.0” top rail sections and secure the joint with seven 3/4" x 2" hex bolts & locknuts (assembled rail should have approx. 2" crown). 2. At each end of the top rail assembly, slide on the top rail supports. 3. -
Page 16: Step 6
STEP 6 Shoe Assembly 1. Unlatch the quick release Catch mechanism on the shoe assembly. 2. Set the shoe assembly on the 4.0” x 6.0” bottom rail in the preferred location. Quick 3. Swing the latch up to the release quick release catch. -
Page 17: Step 7
STEP 7 Trailing Adjustment If the rear axle tracks excessively left or right of the front axle (dog track), then corrective adjustment is made by lengthening or shortening the short tie rod at the rear of the wagon, between the rear axle plate assembly, and the right steering spindle. -
Page 18: Accessories
Accessories LK30 Road Signal Kit This instruction sheet applies to: LK30 Road Signal Light Kit and CHCF36, SHCF36, CHCF45, SHCF45 header Light Bracket wagon models. (30’ wheelbase) Top Plate Light bar assembly and mount. • Assemble the light bracket top plate to the light bar, using two 5/16”x1.0 carriage bolts and lock nuts in the holes indicated. - Page 19 Notes...
- Page 20 HORST WELDING 8082 Rd 129 Listowel, ON N4W 3G8 Canada 519-291-4162 1-866-567-4162 Fax 1-519-291-5388 sales@horstwelding.com www.horstwelding.com...