Page 1
EPSON OPOS ADK MANUAL APPLICATION DEVELOPMENT GUIDE POSPrinter (TM-U330x) Version 3.00 Feb. 2019...
Page 2
(3) Comments and notification of any mistakes in this documentation are gratefully accepted. (4) This software cannot be used with other equipment that the specified. (5) EPSON will not be responsible for any consequences resulting from the use of any information in this documentation. Trademarks Microsoft®, Windows®, Windows Server®, Visual Basic®...
TM-U330BM_BM, TM-U330DM TM-U330DM_BM. Compatibility mode The compatibility mode for upward compatibility was added in OPOS Ver2.60. For the details of the compatibility mode, please refer to “EPSON OPOS ADK MANUAL APPLICATION DEVELOPMENT GUIDE Compatibility Mode”. APPLICATION DEVELOPMENT GUIDE POSPrinter (TM-U330x)
Version 3.00 Feb. 2019 Section 2. Details on Settings This section describes connection configurations and how to make the settings for the TM-U330x Series printers. 2.1. References of Firmware Versions Refer to the release notes (Relnote.txt). 2.2. Port Information 1) Port information when serial port is used The port information that can be set with the SetupPOS utility is as follows.
2.3.1. Usable Device Specific Settings For the TM-U330x, the following device specific settings are settable by the SetupPOS utility. For the detail, please refer to the Section 2 of “EPSON OPOS ADK MANUAL APPLICATION DEVELOPMENT GUIDE POSPrinter (TM Series)”. Settings...
Version 3.00 Feb. 2019 Section 3. Function Details This section describes the functions of the TM-U330x printers in details. Supplementary explanation of the parts not described in detail in the "UPOS" is also given here. 3.1. Property Set Values and Default Values The following explanation is about the property set values and the default values.
Version 3.00 Feb. 2019 This setting is valid only when TM-U330DM_BM is used. If Firmware Version is 1.01 or later version, the following barcode types are supported for TM-U330. ・QR Code ・Code39 ・Code128 ・Code128 parsed 3.1.2. List Properties The List Properties are explained in the following. List Property Settings CharacterSetList...
Version 3.00 Feb. 2019 3.1.3. Width and Height Properties The width and height properties are described below. Property Settings Default Maximum Minimum Value value [dot] value [dot] RecLineSpacing JrnLineSpacing SlpLineSpacing SlpLineHeight [dot] RecLineHeight [dot] JrnLineHeight [dot] SlpLineWidth [dot] RecLineWidth [dot] (When 76.0 mm is set) RecLineWidth [dot] (When 69.5 mm is set)
Version 3.00 Feb. 2019 3.2. Methods The following explanation is about supported/unsupported Methods, and the detailed information. Method Supported/Unsupported PrintNormal PrintTwoNormal PrintImmediate PrintBarCode PrintBitmap PrintMemoryBitmap CutPaper O (1~100: Cutting with one point of the bottom left corner uncut) MarkFeed ChangePrintSide ValidateData TransactionPrint SetLogo...
Version 3.00 Feb. 2019 3.3. Escape Sequences The following figure is about supported/unsupported Escape Sequences. Escape Sequence Support 0~100 0~100 [*]#R 0~9999 #uF Base Pitch [inch] 0~ approx. 50 cm #rF Maximum [inch] [*]#E 0~65535 !rvC !tbC !tpC #stC !stC *#dL O: Supported X : Unsupported...
Version 3.00 Feb. 2019 for TM-U330. ・QR Code ・Code39 ・Code128 ・Code128 parsed 3.4. Printable Barcode Type The TM-U330x models allow the following barcode types. ・QR Code ・Code39 ・Code128 ・Code128 parsed 3.5. QR CODE Printing 3.5.1. QR CODE Printing When printing QR CODE, set the Symbology parameter to one of the following value PTR_BCS_QRCODE: Print using QR CODE model 2.
Version 3.00 Feb. 2019 Therefore, within OPOS it calculates the number of code words of the encoded data. Because of this reason, data amount can be correctly verified. 3.5.3. Error Correction Level Error correction level is fixed at 7%. 3.5.4. Printing Position Like the one dimensional barcode, the print position of the two dimensional barcode is the specified position.
User's Manual”. To print the registered image file, please use the following DirectIO. PTR_DI_FLASH_BITMAP For the details of the printing, please refer to Section 4 of “EPSON OPOS ADK APPLICATION DEVELOPMENT GUIDE POSPrinter (TM Series)”. 3.10. Printable Bitmap Types and Sizes The TM-U330x models support the following bitmap commands.
Version 3.00 Feb. 2019 Section 4. Warnings This section describes precautions in use of TM-U330x. There is no specific warning. APPLICATION DEVELOPMENT GUIDE POSPrinter (TM-U330x)