Advertisement
2-3. INSTALLING SET-UP INFORMATION AND THE
ICC PROFILE (FOR WINDOWS).
Depending on the computer or OS, it may be necessary to use the com-
puter to operate the installation of monitor set-up information etc. If so,
follow the steps below to install the monitor set-up information.
(Depending on the type of computer or OS, command names and meth-
ods may differ. Please follow the computer's own operation manual
while reading this.)
About the ICC profile
An ICC (International Color Consortium) profile is a file that describes
the color characteristics the LCD monitor. By using an application that
works together with an ICC profile, a high color resolution can be real-
ized.
• Windows98, WindowsMe and Windows2000 all use the ICC profile.
• When installing Windows98, WindowsMe and Windows2000 set-up
information (described below), the ICC profile is also installed. If you
would like to install the ICC program only, please refer to Installing
the ICC profile on page 15.
• When using the ICC profile, please set the [WHITE BALANCE] to
[STD].
Installing set-up information
For Windows95
Installing monitor set-up information into Windows95.
This explanation assumes that the floppy disk drive is "A drive".
1. Place the Utility Disk (provided) into the computer's A drive.
2. Click on the [Start] button. From [Settings], choose [Control Panel].
3. Double click on [Display].
4. Click on [Settings], [Advanced Properties], and [Monitor], then
[Change].
5. Click on [Have disk], confirm that [Copy manufacturer's files from:]
is [A:] then click [OK].
6. Confirm that the monitor details are selected, and click [OK].
7. Check that the monitor details are displayed, then click [Apply].
8. Click [OK], and close the window.
9. Remove the Utility Disk from the A drive.
For Windows98
Installing monitor set-up information into Windows98, and setting the
monitor's ICC profile as a predetermined value.
This explanation assumes that the floppy disk drive is "A drive".
If the "Add new Hardware Wizard" has appeared:
1. Place the Utility Disk (provided) into the computer's A drive.
2. Click [Next].
3. Check [Display a list of all the drivers in a specific location, so you
can select the driver you want.], then click [Next].
4. When [Models] is displayed, click on [Have disk], confirm that [Copy
manufacturer's files from:] is [A:], and click [OK].
5. Confirm that the monitor details are selected, then click [Next],
[Next], and [Finish]. If the "Add New Hardware Wizard" appears,
repeat the installation commands beginning from 2 above.
6. Remove the Utility Disk from the A drive.
If the "Add New Hardware Wizard" has not appeared:
1. Place the Utility Disk in the computer's A drive.
2. Click on the [Start] button. From [Settings], choose [Control Panel].
3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. In [Options], check [Automatically detect Plug & Play monitors] and
6. Click [Next].
7. Click on [Display a list of all the drivers in a specific location, so you
8. When [Models] is displayed, click on [Have disk], confirm that [Copy
9. Confirm that the monitor details are selected, then click [Next],
10. Check that the monitor details are displayed, then click [Apply].
11. Click [OK], and close the window.
12. Remove the Utility Disk from the A drive.
For Windows2000
Installing monitor set-up information into Windows2000, and setting the
monitor's ICC profile as a predetermined value.
This explanation assumes that the floppy disk drive is "A drive".
1. Place the Utility Disk (provided) into the computer's A drive.
2. Click on the [Start] button. From [Settings], choose [Control Panel].
3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. Click on [Properties], [Driver] and [Update Driver].
6. When [Upgrade Device Driver Wizard] appears, click [Next].
7. Check [Display a list of the known drivers for this device so that I
8. When [Models] is displayed, click on [Have disk], confirm that [Copy
9. Select the monitor from the list displayed and click [Next].
10. Click [Next], confirm that the monitor's name appears on the
11. Click on [Close].
12. Click [OK], and close the window.
13. Remove the Utility Disk from the A drive.
LL-T15V1
CONNECTION, ADJUSTMENT, OPERATION AND FUNCTIONS
2 – 2
click on [Change].
can select the driver you want.], then click [Next].
manufacturer's files from:] is [A:], and click [OK].
[Next], and [Finish].
can choose a specific driver] and click [Next].
manufacturer's files from:] is [A:], and click [OK].
screen, and click [Finish]. If [The Digital Signature Not Found]
appears, click [Yes].
PC-UM10M
Advertisement
