Siterwell GS511-B-H01 User Manual

Document nr.: GS511-B-H01_Manual Revision nr.: B
Moun
Place the moun te on the desired installa
•
where the holes should be drilled.
Drill two holes with a diameter of 5 millimetres.
•
Push the plas to the holes.
•
Insert the screws into
•
the moun te,
ten them
firmly into the plugs.
Place the smoke alarm
•
on the moun
bracket and secure it
by turning it clockwise.
Test the correct
•
opera our
smoke alarm by
pressing the test
on. If no sound is
generated, the smoke
alarm is not
operly
and should not be
used!
Alarm silence facility
When the smoke alarm has detected smoke and turns into the alarm
mode, you can mute the alarm for approx 10±1 minutes by pressing
the cause of the alarm and make sure that the circumstances are safe.
Overview visual & acous
Opera Visual (flash)
Normal 1 x per 40 seconds
Test 1 x per second (3 x) /
pause of 1,5 seconds
Alarm 1 x per second (3 x) /
pause of 1,5 seconds
Wireless alarm None
Alarm silence 1 x per 8 seconds
Low ba ery warning 1 x per 40 seconds
Connected low ba ery warning 1 x per 3 hours
Low ba ery warning silence None
Fault warning None
-10-
Revision date: 22 12 2020
Low ba ery mode
a When the ba ery is running low, the smoke alarm will indicate this with
a r e beep and flash for approximately 30 days. WARNING: This
smoke alarm is equipped with a non-replaceable ba ery. When this
warning occurs, replace the device as soon as possible! The acous
ba ery warning signal can be muted for ten hours by pressing the test
Ceiling
on. The smoke alarm is s
when it's in this mode.
Fault warning mode
When the smok
fault warning mode. Try cleaning the smoke alarm (see paragraph
maintenance) or replace the smoke alarm!
Maintenance
Test this smoke alarm weekly for correct opera
•
facility. If the smok
beep. Due to the loudness of the alarm, make sure that you always
stand at arm's length distance from the unit when you are tes
the smoke alarm does not generate an acous
alarm must be replaced immediately!
Clean the smoke alarm at least once per month to remove dirt, dust or
•
debris. Use a v
and covers of the smoke alarm. Do not remove the top cover of the
smoke alarm to clean it inside.
Do not a empt to repair this smoke alarm. If the smoke alarm shows a
•
damage related t
Tr
•
Recycling and disposal
The WEEE symbol means that this product and ba eries
must be disposed separately from other household waste.
When they reach their end of life, take them to a designated
waste c
recycling. Protect the environment, human health and natural resources!
Acous
None
1 x per seconds (3 x) /
pause of 1,5 seconds
1 x per seconds (3 x) /
pause of 1,5 seconds
2 x per seconds
None
1 x per 40 seconds
1 x per 3 hours
None
1 x per 40 seconds
o detect smoke
operly, it will turn into the
est
orrectly, it will generate a loud
e
acuum all sides
, it must be replaced!
en caused by dust or steam.
t in your area to guarantee a safe disposal or
operly
Device is being tested
Device has detected smoke
Connected device detected smoke
Smoke alarm is muted
Ba ery is running low
Ba ery of connected device is running low
Low ba ery warning is muted
operly
-11-
SMOKE ALARM
GS511-B-H01 USER MANUAL
FCC warning:
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
IC warning
- English:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) This device must accept any interference, including interference that
may cause undesired operation of the device.
- French:
Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le
brouillageest susceptible d'encompromettre le fonctionnement.
Iden a
Product type : Smoke alarm
Item number : GS511-B-H01
Manufacturer : Siterwell Electronics CO.,LIMITED
Limited : No.666 Qingfeng Road,Jiangbei District,
Ningbo Zhejiang Province, China
Website : www.china-siter.com
Dop: (GS511-B-H01)-CPR-001
EN 14604:2005/AC:2008 0359
Fire Safety
FCC ID: 2ASYYGS511BH01
ESSENTIAL CHARACTERISTICS: PASSED
Nominal activation conditions/ Sensitivity, Response delay (response time) and
Performance under fire condition - Operational reliability - Tolerance to supply voltage
-Durability of operational reliability and response delay, temperature resistance,
vibration resistance, humidity resistance, corrosion resistance, electrical stability
Download the Declaration of Performance at www.china-siter.com