Siterwell GS559B Instruction Manual
  1. Manuals
  2. Brands
  3. Siterwell Manuals
  4. Smoke Alarm
  5. GS559B
  6. Instruction manual

Siterwell GS559B Instruction Manual

Hide thumbs Also See for GS559B:
Table of Contents

Advertisement

Quick Links

Download this manual
Please re
 Please
SIT
TERWE
ELL ELE
Docu
ument NO.: RD
D-559B-39-001
I
nstruc
ction M
Smo
oke Al
Mod
delnumber
r:GS559B
Thank
k you for you
ead the instr
ruction man
e keep the i
instruction m
ECTRON
NICS CO
Manua
al
larm
Ref：ST5
559B
ur support
ual carefull
ly before op
manualfor f
future refere
O.,LIMI
ITED
1
perating
ence
Vers
ion: F

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GS559B and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Siterwell GS559B

Summary of Contents for Siterwell GS559B

  • Page 1 M Manua oke Al larm delnumber r:GS559B Ref：ST5 559B Thank k you for you ur support  Please re ead the instr ruction man ual carefull ly before op perating  Please e keep the i instruction m...

  • Page 2: Product Introduction

    Product Introduction The unit is a photoelectric 3V DC smoke and heat alarm. It is operated by 3v AA Alkaline battery. With the photoelectric technology, it is more sensitive in detecting slow smoldering fires which generate light smoke.little heat and may smolder for hours before bursting into flames.
  • Page 3 Product Configuration Product List:  Smoke Alarm  Bracket  Screw 2pcs  Screw stopper 2pcs  Instruction Wireless function description: Add(Including) alarm to Z-Wave Network :Make sure the battery is installed well before operating the product. 2:Make sure the alarm is on its final install location, then set the controller into the Add(Inclusion )mode.

  • Page 4: Command Classes

    Linkage group 2 is assigned to the devices status - sending BASIC SET control frame to the associated devices having detected the smoke alarm. Linkage group 3 reports the detection's status to the associated device. smoke alarm Linkage group 4 is assigned to the devices status - sending BASIC SET control frame to the associated devices having detected the heat alarm.

  • Page 5: Important Safety Information

    3:Replacement Required,Unspecified reason(0x04) 4:Alarm Silenced(0x06) Supported Notification Type: Heat Alarm Heat Alarm Supported Event: 1:Overheat detected,Unknown Location(0x02) 2:Heat Alarm Test(0x07) 3:Replacement Required,End-of-life(0x08) 4:Alarm Silenced(0x09) Important Safety Information: 1. The test button accurately tests smoke alarm functions. Do not use any other test method. Test smoke alarm weekly to ensure proper operation.
  • Page 6 smoke alarm weekly and replace them every 10 years. Do Not Install Smoke Alarms in the Following Places: 1:Near appliances or areas where normal combustionRegularly occurs (kitchens, near furnaces, hot water heaters).Use specialized smoke alarm device with unwanted alarm control for this areas.

  • Page 7: Recommended Locations For Alarms

    Diagram1 RECOMMENDED LOCATIONS FOR ALARMS: • Locate the first alarm in the immediate area of the bedrooms. Try to monitor the exit path as the bedrooms are usually farthest from the exit. If more than one sleeping area exists, locate additional alarms in each sleeping area.

  • Page 8: Installation Steps

    Diagram 4 Diagram 4 Diagram 2 Diagram 3 Diagram 5 Installation Steps ·Fix the two AA batteries to each battery box of the smoke alarm. “Wireless function description” ·According to the Section to operate the smoke alarm. Ensure the wireless function is ok. ·Then press the bracket on the installation position, mark installation hole of bracket with pencil.
  • Page 9 ·If you have any questions on installation, you can contact your retailer. ·During testing, may the other smoke detector will alarm. Once release the button, others will stop alarming in 1 minute. In such a way, you can check the wireless function. WARNING: To prevent injury, this unit must be securely attached to the ceiling in accordance with the installation instructions.
  • Page 10 This smoke alarm is equipped with red LED indicators. Standby Condition: The red LED will flash every 50 seconds to indicate that the smoke alarm is operating properly. Alarm Condition: When the alarm senses products of combustion and goes into alarm, the red LED will flash rapidly (one flash per second).The rapid flashing LED and pulsating alarm will continue until the air is cleared or the test button is released.

  • Page 11: What To Do When The Alarm Sounds

    the air has been cleared of the condition causing the alarm. CAUTION: Before using the alarm silence (silence), identify the source of the smoke and be certain a safe condition exists. DANGER: If the alarm sounds, and it is not being tested, it means the unit is sensing smoke, SOUND OF THE ALARM REQUIRES YOUR IMMEDIATE ATTENTION AND ACTION.

  • Page 12: Maintenance And Cleaning

    once seconds. Smoke alarm chirp Clean smoke alarm. Please refer to the “maintenance and occurs every 50 seconds cleaning” section. Replace smoke alarm if the problem （alarm goes into fault persists mode）. Smoke alarm sounds 1. Press test button to silence alarm. unwanted alarms 2.

  • Page 13: Manufacturer Information

    If after reviewing this manual you feel that your smoke alarm is defective in any way, do not tamper with the unit. Return it for servicing to Manufacturer: Manufacturer information: SITERWELL ELECTRONICS CO.,LIMITED ADDRESS: NO.76 HAICHUAN ROAD CHUANGYE ZONE B, JIANGBEI, NINGBO, CHINA TEL:0086-574-87729581 FAX:0086-574-87729581,E-MAIL:Sales@china-siter.com...

Table of Contents