Table of Contents
Advertisement
Available languages
Available languages
English
minimum wire size. The following table shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
Minimum gauge for Cord sets
Total length of Cord in Feet
Volts
120 V
25 (7.6)
240 V
50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
More
not
Than
More
Than
0
6
18
6
10
18
10
12
16
12
16
14
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
6
(meters)
50 (15.2) 100 (30.5) 150 (45.7)
American Wire gauge
16
16
16
14
16
14
12
Not Recommended
or AC ........... alternating current
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
PSI....................... pounds per square
inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all
documentation
Specifications
Maximum Pounds per Square Inch*
Rated Gallons per Minute*
Electrical Requirements
Electrical Cord
High Pressure Hose
Minimum Amp Source
Pressure of Inlet Water
Inlet Water
14
*Water flow and maximum pressure ratings determined in accordance with
12
CETA CPC‑100.
12
Cage Carrying Handles (Fig. B)
This pressure washer has a protective cage that protects the
pressure washer from daily jobsite abuse but also provides
mulitiple carry handle
using whichever part of the cage that is convenient for
your application.
Telescoping Handle (Fig. C)
This pressure washer has a convenient, built in telescoping
handle and transport wheels.
1. To unlock the telescoping handle
release button
hear an auidible click when it snaps into position.
2. To store the telescoping handle
release button
down and into the pressure washer body. You will hear an
auidible click when it snaps into position.
3. To move the pressure washer
transport wheels
unit by the telescoping handle.
Accessory Storage Compartment (Fig. D)
This pressure washer has a built in accessory storage
compartment
handle grip and turbo nozzle.
1. To unlock the storage door
latch
11
counterclockwise and flip the door down
to access the spray wand
grip
5
, and turbo nozzle
2. To lock the storage door
closed position. Rotate the door latch
the storage door into position.
Assembling Spray Wand (Fig. E)
1. To connect the spray handle
insert the threaded end of the spray handle onto the
threaded end of the handle grip. Rotate the spray handle
clockwise until fully tightened.
2. To connect the spray wand
the threaded end of the spray wand into the threaded
collar
29
of the spray handle. Rotate the threaded
collar
29
clockwise until fully tightened.
12
options. Carry the pressure washer
13
14
and slide the handle upwards. You will
13
, press the handle
14
and slide the telescoping handle
8
, tilt the unit so the
21
are touching the ground and pull the
34
to carry the spray wand, spray handle,
10
, rotate the door
2
, spray handle
22
.
10
, lift the storage door up to the
4
to the handle grip
2
to the spray handle
2100
1.2
120V
~60Hz, 13A
AC
35 ft. (10.6 m)
25 ft. (7.6 m)
15A
20‑100 PSI
Cold Tap
, press the handle
4
, handle
11
clockwise to lock
5
,
4
4
, insert
Hide quick links:
Advertisement
Table of Contents
