Operation; Pressure Adjustments - DeWalt DXPW3200V Manual


WARNING: RISK OF HOT SURFACES
WhAT CAn hAPPEn
• Contact with hot surfaces,
such as engines exhaust
components, could result
in serious burn.

WARNING: RISK OF INJURY FROM LIFTING
WhAT CAn hAPPEn
• Serious injury can result
from attempting to lift too
heavy an object.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Description (Fig. A, G, K)

WARNING: Never modify the pressure washer or any part
of it. Damage or personal injury could result.
nOTE: Photographs and line drawings used in this
manual are for reference only and do not represent a
specific model.
High Pressure Pump
1
Engine
2
High Pressure Hose
3
Spray Gun
4
Quick-Connect Spray Wand
5
Detergent Siphon Hose (Fig. K)
6
Handle
7
Frame
8
Pump Outlet
9
Pump Inlet
10
Quick Connect Nozzles
11
Detergent Tank
12
Intended Use
Your pressure washer has been designed for
professional applications.
DO nOT let children come into contact with the pressure
washer. Supervision is required when inexperienced operators
use this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
hOW TO PREVEnT iT
• During operation, touch
only the control surfaces
of the pressure washer.
Keep children away from
the pressure washer at
all times. They may not
be able to recognise the
hazards of this product.
hOW TO PREVEnT iT
• The pressure washer is too
heavy to be lifted by one
person. Obtain assistance
from others before lifting.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY
Pressure Washer Assembly (Fig. B, C–F)
1. Locate and remove all loose parts from the carton.
2. Cut four corners of the carton from top to bottom and lay the
panels flat.
3. Place handle 7 onto frame
and slide the handle assembly onto the frame until snap
buttons snap into place.

CAUTION: Risk of personal injury. Avoid placing
hands between handle and frame when assembling to
prevent pinching.
4. Attach high pressure hose
is secure.
5. Connect wand 5 to spray gun
is secure.
6. Remove the five coloured quick-connect nozzles from the
plastic bag and insert them into correct grommet on the
nozzle holder. Nozzles are colour coded to match coloured
nozzles on panel assembly.
7. Check the tyre pressure and add air if needed.
nOTE: Air tanks, compressors and similar equipment used
to inflate tyres can fill small tyres similar to these very rapidly.
Adjust pressure regulator on air supply to no more than the
rating of the tyre pressure. Add air in small increments and
frequently use the tyre gauge to prevent over inflation.

WARNING: Risk of bursting. Use a tyre pressure gauge
to check the tyres pressure before each use and while
inflating tyres; see the tyre sidewall for the correct
tyre pressure.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

Pressure Adjustments

The pressure setting is preset at the factory to achieve
optimum pressure and cleaning. To lower the pressure, follow
these instructions.
1. Back away from the surface to be cleaned. The further away
the nozzle is, the less the pressure will be on the surface to
be cleaned.
2. Change to the 40˚ nozzle (white). This nozzle delivers a less
powerful stream of water and a wider spray pattern. Refer to
spray Wand nozzles.
NOTICE: DO NOT attempt to increase pump pressure. A
higher pressure setting than the factory set pressure may
damage pump.
English
8 , depress the snap buttons,
3 to spray gun 4 . Make sure it
4 . Make sure connection
7