Advertisement
Quick Links
© 2019 KORG INC. www.korg.com
Published 05/2020 Printed in Vietnam
The video assembly tutorial for the NTS-1 digital
kit is available here:
For more information:
https://www.korg.com/nts_1/
ARP
EG
2
OSC
FILTER
2
INPUT
TRIM
ROUTE
EFGSJ 2
VOLUME
2
2
2
MOD
DELAY
REVERB
1
Precautions During Assembly
En
• Before assembly, discharge the static electricity from your body by
touching the ground wire of a grounded device or similar methods.
Failure to do so will cause a malfunction.
• Carefully handle the circuit boards to avoid injuries that could
be inadvertently caused by protruding parts. In addition, be sure
to wash your hands with soap when finished with the assembly
procedure.
• Be sure to align screws properly before tightening them. In addi-
tion, be careful not to tighten screws with excessive force or over
tighten them, otherwise the parts may be damaged.
• Provide a sufficiently large work space to complete the assembly
procedure, and prepare work mats so parts will not be scratched.
• Carefully handle the included screws so they will not be lost. In
addition, do not use screws other than those included for assem-
bly, and do not use the included screws for any other purpose.
Checking package contents
Before beginning the assembly process, make sure that all of the
parts are available. Extra screws are included. Use them as spares.
If any part is missing or damaged, contact your local Korg distributor.
2
2
Advertisement
Related Manuals for Korg Nu:Tekt NTS-1 digital kit
Summary of Contents for Korg Nu:Tekt NTS-1 digital kit
- Page 1 • Carefully handle the circuit boards to avoid injuries that could be inadvertently caused by protruding parts. In addition, be sure to wash your hands with soap when finished with the assembly procedure. • Be sure to align screws properly before tightening them. In addi- tion, be careful not to tighten screws with excessive force or over tighten them, otherwise the parts may be damaged. • Provide a sufficiently large work space to complete the assembly EFGSJ 2 procedure, and prepare work mats so parts will not be scratched. • Carefully handle the included screws so they will not be lost. In © 2019 KORG INC. www.korg.com Published 05/2020 Printed in Vietnam addition, do not use screws other than those included for assem- bly, and do not use the included screws for any other purpose. Checking package contents Before beginning the assembly process, make sure that all of the parts are available. Extra screws are included. Use them as spares. If any part is missing or damaged, contact your local Korg distributor. The video assembly tutorial for the NTS-1 digital kit is available here: For more information: https://www.korg.com/nts_1/...
- Page 2 VOLUME: Sets the volume of the signal output to the speaker and Never set any container with liquid in it near this equipment. If liquid gets into Be sure to use an AC adapter that conforms to USB2.0 standards. However, (Headphone) jack. the equipment, it could cause a breakdown, fire, or electrical shock. there may be cases where, depending on the USB AC adapter used, it will AUDIO IN jack: Stereo audio input. The gain trim and mix route can be set Be careful not to let metal objects get into the equipment. If something does slip not function normally even when compatible with the standards. using global parameters. into the equipment, unplug the AC adapter from the wall outlet. Then contact Turning off the power your nearest Korg dealer or the store where the equipment was purchased. IN–SYNC–OUT (SYNC IN, SYNC OUT) jacks: These jacks allow you to synchronize your NTS-1 digital kit to a Korg volca, monotribe or other Disconnect the USB cable from the NTS-1 digital kit. Once disconnected all LEDs will go dark (unlit). equipment—including an analog sequencer or a DAW. The polarity of the SYNC jacks can be set using the global parameters. SLEEP MODE SYNC OUT jack: A 5 V pulse of 15 ms is sent at the beginning of each step. After 15 minutes of inactivity the device will enter sleep mode. Press the SYNC IN jack: If this jack is connected, the internal step-clock will be ignored, OSC button to wake up the device and return to normal operation. and the NTS-1 digital kit ARP will advance according to the pulses received here.
- Page 3 Assembly ⒻⒼⒷⒾ Rear panel Lower PCB Front panel Bottom panel (1 ) (Screws 2.5 x 5 mm): 8 Upper PCB Keyboard sheet (Screws 2.0 x 8 mm): 16 Side panels: 2 Corner blocks: 4 Rubber feet Phillips (+) screwdriver ⒶⒽ Do not bend the flat cable Ⓗ.
- Page 4 • Are the parts mounted in the correct direction? • Is the kit built securely, without wobbling? Troubleshooting Extra parts remaining, or parts missing. There are more screws than the number that will be used. Make sure that the circuit boards for (1) are not If any parts are missing, contact your local Korg distributor. misaligned when inserting. If any parts are damaged or missing before beginning the assem- The section on Ⓑ with holes indicated by an bly procedure, contact your local Korg distributor. arrow is the rear side. The unit makes an abnormal sound when tilted or shaken after assembly.