KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 1 Safety Precautions 1.1. For Service Technicians • Repair service shall be provided in accordance with repair technology information such as service manual so as to pre- vent fires, injury or electric shock, which can be caused by improper repair work. 1.
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 2.2.1. Suggested PbF Solder There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper (Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the manufacturer’s specific instructions for the melting points of their products and any precautions for using their product with other materials.
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 3 Specifications Note: • Design and specifications are subject to change without notice. Note for Service: • Operation range: Up to 300 m outdoors, Up to 50 m indoors, depending on condition • Analog telephone connection: Telephone Line...
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 4.2. Circuit Operation (Base Unit) 4.2.1. Outline Base Unit consists of the following ICs as shown in Block Diagram (Base Unit) (P.7). • DECT BBIC (Base Band IC): IC3 (career module) - Handling all the audio, signal and data processing needed in a DECT base unit - Controlling the DECT specific physical layer and radio section (Burst Module Controller section) - ADPCM codec filter for speech encoding and speech decoding (DSP section) - Echo-cancellation and Echo-suppression (DSP section)
Page 9
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 4.2.3. Telephone Line Interface <Function> • Bell signal detection • Clip signal detection • ON/OFF hook circuit • Audio circuits Bell & Clip (: Calling Line Identification Presentation: Caller ID) signal detection: In the standby mode, Q3 is open to cut the DC loop current and decrease the ring load. When ring voltage appears at the BATTERY (+) and BATTERY (-) leads (when the telephone rings), the signal is transferred as fol- lows;...
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 5 Location of Controls and 6 Installation Instructions Components 6.1. Connections 5.1. Location of Controls 5.1.1. Base Unit 5.1.2. Handset...
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 6.2.3. Battery Level 6.2.4. Panasonic Ni-MH Battery Perfor- mance (supplied batteries) 6.2. Battery 6.2.1. Battery Installation See For Service Hint (P.17) Note for service: The battery strength may not be indicated correctly if the battery is disconnected and connected again, even after it is fully charged.
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 7 Operating Instructions 7.1. Guide to Base Unit Settings Cross Reference: For Service Hint (P.17)
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 7.2. Guide to Handset Settings 7.3. Dialling mode Cross Reference: For Service Hint (P.17)
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 7.4. For Service Hint Cross Reference: Battery Charge (P.14)
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 8 Service Mode 8.1. Engineering Mode 8.1.1. Base Unit Note: (*1) Refer to For Service Hint (P.17).
Page 19
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW Frequency Used Items (Base Unit) ex.) Items (*2) Address Default Data New Data Remarks C-ID (FSK) sensi- 0A1D~0A1E 00 28 (3dB up) (6dB up) When hex changes from “006D” to “00A4” or “00E7”, tivity 00 A4 00 E7 gain increases by 3dB or 6dB. C-ID (DTMF) sen- 0A 2D (3dB up)
Page 20
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 8.1.2. Handset Note: (*1) Refer to For Service Hint (P.17).
Page 21
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW Frequency Used Items (Handset) ex.) Items (*4) Address Default Data New Data Possible Adjusted Possible Adjusted Remarks Value MAX (hex) Value MIN (hex) Sending level 0F 35 Adjusted value Given value (*1) Receiving level 0F 37 Adjusted value Given value (*2) Battery Low 0F 04...
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 9 Troubleshooting Guide 9.1. Troubleshooting Flowchart Flow Chart Cross Reference: Check Power (P.23) Bell Reception (P.27) Check Battery Charge (P.24) Check Link (P.25) Check Handset Transmission (P.27) Check Handset Reception (P.27) Signal Route (P.12) Check Caller ID (P.27)
Page 23
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 9.1.1. Check Power 9.1.1.1. Base Unit Is the AC Adaptor inserted into AC outlet? (Check AC Adaptor’s specification.) Cross Reference Power Supply Circuit (P.8) 9.1.1.2. Handset Cross Reference Power Supply Circuit/Reset Circuit (P.11)
Page 24
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 9.1.2. Check Battery Charge 9.1.2.1. Base Unit Cross Reference: Power Supply Circuit (P.8) 9.1.2.2. Handset Cross Reference: Check Power (P.23) Charge Circuit (P.11) 9.1.2.3. Charger Unit Cross Reference: Power Supply Circuit (P.11)
Page 25
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 9.1.3. Check Link 9.1.3.1. Base Unit Cross Reference: Power Supply Circuit (P.8) Check Point (Base Unit) (P.28) Note: (*1) Refer to Troubleshooting by Symptom (Base Unit and Charger Unit) (P.28).
Page 26
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 9.1.3.2. Handset Cross Reference Power Supply Circuit/Reset Circuit (P.11) Check Point (Handset) (P.31) Note: (*1) Refer to Troubleshooting by Symptom (Handset) (P.31).
Page 27
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 9.1.4. Check Handset Transmission Cross Reference: Signal Route (P.12) 9.1.5. Check Handset Reception Cross Reference: How to Check the Handset Speaker or Receiver (P.46). Signal Route (P.12) 9.1.6. Check Caller ID Cross Reference: Signal Route (P.12) 9.1.7. Bell Reception 9.1.7.1.
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 9.2. Troubleshooting by Symptom (Base Unit and Charger Unit) If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester (*1) or not. Note: (*1) A general repair is possible even if you don’t have the DECT tester because it is for confirming the levels, such as Acoustic level in detail.
Page 29
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW Items Adjustment Procedure Check or Point Replace Parts (F)* Hookswitch Check with 1. Connect J1 (Telephone Socket) to Tel-simulator which is connected with 600 Career mod- Ω. DC Characteristics ule. C30, C31, 2. Set line voltage to 48V at on-hook condition and line current to 40mA at off- D2, Q3, Q2, hook condition of normal telephone.
Page 30
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW Items Adjustment Procedure Check or Point Replace Parts (L)* Timing Confirmation Follow steps 1 to 3 of (H). Career mod- 4. Confirm that the Timing accuracy is < ± 2.0ppm. ule, C4, C6, C2, C3, C25, C8, C1, C12, C13, C7, L1, L2, C18, C19, D1, C17, R2,...
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 9.3. Troubleshooting by Symptom (Handset) If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester (*1) or not. Note: (*1) A general repair is possible even if you don’t have the DECT tester because it is for confirming the levels, such as Acoustic level in detail.
Page 32
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW Items Adjustment Procedure Check or Point Replace Parts (G) Battery Low Confirma- 1. Apply 2.40V between BATTERY (+) and BATTERY (-). Career mod- tion (Important) 2. Confirm that there is no Speaker sound (Battery low alarm). ule,D107, 3. Apply 2.1V between BATTERY(+) and BATTERY(-). C109, C125, 4.
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 11 Measurements and Adjustments 11.1. The Setting Method of JIG (Base Unit) 11.1.1. Preparation 11.1.1.1. Equipment Required • DECT tester: Rohde & Schwarz, CMD 60 is recommended. • Frequency counter: it must be precise to be able to measure 1Hz (precision; ±4ppm). Hewlett Packard, 53131A is recommended.
Page 38
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 11.1.2.2. Batch file Setting Note: • “*****” varies depending on the country. 11.1.2.3. Commands See the table below for frequently used commands. Command name Function Example rdeeprom Read the data of EEPROM Type “rdeeprom 00 00 FF”, and the data from address “00 00” to “FF” is read out.
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 11.2. Adjustment Standard (Base Unit) When connecting the simulator equipments for checking, please refer to below. 11.2.1. Bottom View (F), (G), (O) AF VOLT LOOP AF VOLT METER Simulator METER BELL Simulator Call - ID Dummy Handset Simulator DTMF Tester DC POWER DC_IN...
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 11.3. Adjustment Standard (Charger Unit) When connecting the Simulator Equipments for checking, please refer to below. 11.3.1. Bottom View Digital Volt Meter /2 W DC POWER DC 6.5 V Note: (A) is referred to Check Point (Charger Unit) (P.30)
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 11.4. The Setting Method of JIG (Handset) 11.4.1. Preparation 11.4.1.1. Equipment Required • DECT tester: Rohde & Schwarz, CMD 60 is recommended. • Frequency counter: it must be precise to be able to measure 1Hz (precision; ± 4ppm). Hewlett Packard, 53131A is recommended. •...
Page 42
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 11.4.2.2. Batch file Setting Note: • “*****” varies depending on the country. 11.4.2.3. Commands See the table below for frequently used commands. Command name Function Example rdeeprom Read the data of EEPROM Type “rdeeprom 00 00 FF”, and the data from address “00 00” to “FF” is read out.
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 11.5. Adjustment Standard (Handset) When connecting the Simulator Equipments for checking, please refer to below. 11.5.1. Component View AF VOLT Volt Meter METER REV+ REV- LOOP Simulator DECT Tester D103 C112 D102 CMD60 D105 D106 (I), (J), (K), (L), (M), (N) R112 C155 Dummy Base...
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 11.6. Things to Do after Replacing IC Cautions: Since this page is common to each country, it may not apply to some models in your country. The contents below are the mini- mum adjustments required for operation. 11.6.1. Base Unit Before doing the following adjustment, be sure to do PC Setting (P.37) in The Setting Method of JIG (Base Unit).
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 11.7. RF Specification 11.7.1. Base Unit Item Value Refer to -. * TX Power More than 14 dBm ~ 26 dBm Check Point (Base Unit) (H) Modulation 340 kHz/div ~ 402 kHz/div Check Point (Base Unit) (I) Frequency Offset -50 kHz ~ +50 kHz Check Point (Base Unit) (J) RX Sensitivity...
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 11.8. How to Check the Handset Speaker or Receiver 1. Prepare the digital voltmeter, and set the selector knob to ohm meter. 2. Put the probes at the speaker terminals as shown below. 11.9. Frequency Table (MHz) BASE UNIT HANDSET Channel No Transmit Frequency...
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 12.3. Terminal Guide of the ICs, Transistors and Diodes 12.3.1. Base Unit 12.3.2. Handset...
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 13 Schematic Diagram 13.1. For Schematic Diagram 13.1.1. Base Unit (Schematic Diagram (Base Unit)) Notes: 1. DC voltage measurements are taken with voltmeter from the negative voltage line. 2. This schematic diagram may be modified at any time with the development of new technology. 13.1.2.
Page 62
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 14.3.2. Bottom View BOOK PROG TALK LEFT RIGHT REDIAL CANCEL DOWN KX-TGA131 CIRCUIT BOARD (Handset_Main (Bottom View))
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 15 Exploded View and Replacement Parts List 15.1. Cabinet, Electrical Parts and Accessories (Base Unit/Handset) Note: (*1) When replacing Antenna, refer to Handset (P.34) of Disassembly and Assembly Instructions.
KX-TG1381HKH/KX-TG1381HKV/KX-TG1381HKW/KX-TG1382HKH/KX-TGA131HMH/KX-TGA131HMV/KX-TGA131HMW 15.2. Replacement Part List 15.2.2. Handset 1. RTL (Retention Time Limited) Note: 15.2.2.1. Cabinet and Electrical Parts The “RTL” marking indicates that its Retention Time is Limited. When production is discontinued, this item will con- Safety Ref. Part No. Part Name &...