Table of Contents
Advertisement
H9450UD(EN).qx33
03.1.22 7:19 PM
COPYING A VIDEO TAPE
You can make copies of video tapes made by friends or
relatives for your enjoyment.
Warning:
Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
Connect the recording DVD/VCR (this unit), the play-
ing VCR (another source) and your TV using the fol-
lowing diagram.
You can use the AUDIO/VIDEO input jacks on the
¡
front panel of the DVD/VCR instead of using the
jacks on the back.
[Recording DVD/VCR]
(this unit)
DVD/VCR
VCR
AUDIO OUT AUDIO IN
ANT-IN
L
L
R
R
ANT-OUT
VIDEO OUT VIDEO IN
Coaxial cable
(supplied)
[TV set]
(Use for monitoring)
ANT in
1
Insert a pre-recorded tape into the playing
VCR.
2
Insert a tape with a safety tab into the
recording VCR.
3
Press SPEED on the recording VCR to
select the desired recording speed
(SP/SLP).
4
Select the "L1" or "L2"position on the
recording DVD/VCR by pressing the CHAN-
NEL (K/L ).
When you use the A/V input jacks on the back of the
¡
DVD/VCR, select "L1" position by pressing [0], [0],
[1] on the remote control or the CHANNEL(o/p) Buttons.
¡
When you use the A/V input jacks on the front of the
DVD/VCR, select "L2" position by pressing [0], [0],
[2] on the remote control or the CHANNEL(o/p) Buttons.
Note
"L1" and "L2" are found before the lowest memo-
rized channel. (Example: CH2)
5
Press REC/IRT on the recording VCR.
6
Begin playback of the tape in the playing
VCR.
For best results during dubbing, use the DVD/VCR's
¡
front panel controls whenever possible. The remote
control might affect the playing VCR's operation.
Page 22
SPECIAL FEATURES
VCR
DVD
S-VIDEO
CONPONENT
AUDIO
DIGITAL
OUT
VIDEO OUT
OUT
AUDIO OUT
Y
C
B
L
P
B
COAXIAL
I
P
C
R
R
P
R
PROGRESSIVE
Audio/Video cables
(not supplied)
OUT
IN
LEFT
AUDIO
RIGHT
VIDEO
[Playing VCR]
(another source)
Always use video-quality shielded cables with
¡
RCA-type connectors. Standard audio cables are not
recommended.
You can use a video disc player, satellite receiver,
¡
camcorder or other audio/video component with
A/V outputs in place of the playing VCR.
TO MONITOR THE RECORDING
1
Turn on the TV and set the TV to channel 3.
If noise appears, change the RF output channel of
¡
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same channel
(CH4) on your TV. (See "RF Output Channel" on
page 13 for the detail).
2
Press VCR/TV on the remote control of the
recording DVD/VCR.
MTS (Multi-Channel Television
Sound) SYSTEM
When you play a VHS tape, or receive a broadcast on
the VCR tuner channel you are
watching, the current status will
appear when you press DIS-
PLAY on the remote control.
When you record a MTS broad-
cast signal, you need to set it to
MTS mode.
1)*
Press MENU and select "TV STEREO" or
"SAP" by pressing K or L. Then, press B
for fix mode. To exit, press
CLEAR/C.RESET.
Although a program may be broadcast in both stereo
¡
and sub audio, you must select the Recording mode
to TV STEREO or SAP before you record a broad-
cast.
2)*
Press MENU and select "AUDIO OUT" by
pressing K or L. Then, press B. Next,
select "HIFI" or "MONO" by pressing K or
L. To exit, press CLEAR/C.RESET.
¡
While the VCR is set in HIFI stereo mode, HIFI
appears on the TV screen. While the VCR is set in
monaural (MONO) mode, HIFI disappears from the
TV screen.
MTS RECORDING/MONITOR MODE
Type of
Display on the
STEREO/SAP
TV screen
broadcast
Selection
Regular
-None-
-Invalid-
(monaural audio)
Stereo
STEREO
- nvalid-
I
broadcast
SAP
TV STEREO*
Bilingual
broadcast
SAP*
TV STEREO*
Stereo &
STEREO
Bilingual
SAP
SAP*
broadcast
*
– 22 –
VCR
STOP
12:00AM
CH 32
1)*
STEREO
SAP
2)*
SP
0:00:00
HIFI
Hi-Fi audio track
Normal audio
(2-channel)
track
L-channel
R-channel
Mono
Mono
Mono
L
R
L+R
Main audio
Main audio
Main audio
program
program
program
Sub audio
Sub audio
Sub audio
program
program
program
L
R
L+R
Sub audio
Sub audio
Sub audio
program
program
program
EN
1L25
Hide quick links:
Advertisement
Table of Contents
