Melal Part cal return path to the chassis. Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the out- ohmmeter let and repeat the test. See Fig. 1-1. Fig. 1-2 Insulation Resistance Test Samsung Electronics...
Page 3
(5) antenna wiring. Always inspect in all areas tinuously and new instructions are issued whenev- for pinched, out-of-place, or frayed wiring, Do not er appropriate. change spacing between a component and the printed-circuit board. Check the AC power cord for damage. Samsung Electronics...
Page 4
Components i-enti- fied by shading, by( ) or by ( ) in the circuit dia- gram are important for safety or for the characteris- tics of the unit. Always replace them with the exact replacement components. Samsung Electronics...
Page 5
(6) Do not remove a replacement ESD device from its protective package until immediately before your are ready to install it.(Most replacement ESD devices are packaged with leads electrically short- ed together by conductive foam, aluminum foil or comparable conductive materials). Samsung Electronics...
Page 6
Be sure to put on a wrist strap grounded to the sheet. Be sure to lay a conductive sheet made of copper etc. Which is grounded to the table. Samsung Electronics...
Page 7
4) Insert FPC into Main PCB CN6 and switch SW3 on 4) Disassemble the deck PCB. deck PCB to “ON”. (See Fig 1-4) Note : If the assembly and disassembly are not done in correct sequence, the Pick-up may be damaged. TO MAIN PCB (CN6) Fig. 1-4 Samsung Electronics...
Page 10
All manuals and user guides at all-guides.com Reference Information Samsung Electronics...
Page 11
All manuals and user guides at all-guides.com Reference Information 2-1-3 SIC1 (KS1452 ; Digital Servo) DIRC SSTOP /PSO SMON LOCK DFCT FOKB MIRR TZCA PHI1 XOUT TEST RSTB TILTO TILTI Samsung Electronics...
Page 12
All manuals and user guides at all-guides.com Reference Information Samsung Electronics...
Page 13
All manuals and user guides at all-guides.com Reference Information 2-1-4 DIC1 (KS1453 ; DVD Data Processor) Samsung Electronics...
Page 14
All manuals and user guides at all-guides.com Reference Information Samsung Electronics...
Page 15
D a t a O u t p u t E n a b l e P o w e r ( + 5 V ) P o w e r ( + 3 . 3 V ) N . C No Connection Samsung Electronics...
Page 16
D V D - D A T A 7 / C D G - S C L K Global VREQUEST I n t e r f a c e VSTROBE A_VSS Signals A_VDD ERROR P10[10:0] V-DACK/ASTROBE AREQUEST R E S E T A-DACK ZiVA Decoder Samsung Electronics...
Page 17
Raster Contral 1 for video port. This pin receives/provides a VS/FS/FSEQ signal. RCV1 Raster Contral 2 for video port. This pin provides an HS pulse of programmable length or receives I / O RCV2 an HS pulse. 2-10 Samsung Electronics...
Page 18
The 12C-bus receiver waits for the START condition. S C L 12C serial clock input S D A I / O 12C serial data input/output TTXRQ Teletext Request output, indicating when text bits are requested T T X Teletext bit stream input Samsung Electronics 2-11...
Page 24
Auxillary Digital Audio and S/PDIF Receiver Signals Receiver Channel 1 SCLKAUX/RX2 Auxillary Digital Audio and S/PDIF Receiver Signals Auxiliary Bit Clock Input or OutputReceiver Channel 2 LRCKAUX/RX3 Auxillary Digital Audio and S/PDIF Receiver Signals Auxiliary Word Clock Input or OutputReceiver Channel 3 Samsung Electronics 2-17...
Page 25
2-1-11 AIC2 (W27C020 ; 2MB EPROM) BLOCK DIAGRAM OUTPUT CONTROL BUFFER CORE DECODER ARRAY FUNCTION NAME A0 - A17 Address Inputs Data Input/Outputs Q0 - Q7 Chip Enable Output Enable Program Enable Program/Erase Supply Voltage Power Supply Ground 2-18 Samsung Electronics...
Page 26
Chip Enable and Output Buffers Prog Logic Gating Decoder A0-A19 Address 2,097,152-Bit Inputs Cell Matrix Decoder TOP VIEW FUNCTION NAME A0-A19 Address Inputs Chip Enable Input Data Input/Outputs DQ0-DQ7 Output Enable Input Vcc Syply Voltage OE/VPP Ground Samsung Electronics 2-19...
Page 27
All manuals and user guides at all-guides.com Reference Information 2-1-13 FIC1 (LC86P6232 ; Front Micom) 2-20 Samsung Electronics...
Page 28
* S/N Ratio 110 dB * Dynamic Range 96 dB * Total Harmonic Distortion 0.003 % Output Power 200 watt (5 channels by 40 watts, 8 ohm) Speaker Output *Total Harmonic Distortion 0.08 % * : Nominal specification Samsung Electronics...
Note : If Tray Œ doesn’t open, insert a Screw driver ¨ into the Emergency hole ˇ(as shown in detailed draw- ing) and then turn it in the direction of arrow “B”. Open Tray manually. Œ TRAY ´ DOOR-TRAY "A" ˇ EMERGENCY HOLE "B" ¨ SCREW DRIVER <Bottom View> Fig. 5-1 Door-Tray Removal Samsung Electronics...
Page 35
1) Remove 5 Screws Œ on the back Top Cabinet. 2) Remove 4 Screws ´, ˇ on the left and right side. 3) Lift up the Top Cabinet in direction of arrow. ´ 2 SCREWS Œ 5 SCREWS ˇ 2 SCREWS Fig. 5-2 Top Cabinet Removal Samsung Electronics...
Page 39
All manuals and user guides at all-guides.com Disassembly and Reaasembly 5-2 PCB Location S.M.P.S. PCB JACK PCB MAIN PCB AMP PCB HEADPHONE PCB FRONT PCB Fig. 5-6 PCB Location Samsung Electronics...
Page 40
MAIN PCB Æ ı AMP PCB CNFAN ˜ ¯ POWER TRTANS POWER TRANS AMP PCB CNTRNS ˘ ¿ CNJACK AMP PCB CT10 JACK PCB CONNA ¸ ˛ POWER TRTANS POWER TRANS CT11 S.M.P.S. PCB PCN02 Fig. 5-7 Connector Diagram Samsung Electronics...
Page 41
3) Pull the Tray Ø to disassemble, while simultaneously pushing the Hook ∏, ” in direction of arrow “A”, “B”. Œ 2 SCREWS ´ COVER SHEET ˇ ASS'Y - DECK CLAMPER ∏ HOOK "C" "B" "D" ” HOOK Ø TRAY ˆ SCREW DRIVER "A" ¨ EMERGENCY HOLE <Bottom View> Fig. 5-8 Tray Removal Samsung Electronics...
Page 42
2) Disassemble the Ass’y-Deck Sub ¨ in direction of arrow “B”, while simultaneously pushing the Hook ˇ in direction of arrow “A”. ¨ ASS'Y - DECK SUB "B" "A" ˇ HOOK ´ ASS'Y - PCB DECK Œ 2 SCREWS Fig. 5-9 Ass’y-Deck Sub Removal Samsung Electronics...
Page 43
ALIGN TWO ARROWS ’ GEAR - CAM SUB Æ GEAR - SYNCRO Ú SHAFT - SYNCRO Æ GEAR - SYNCRO Ò LEVER - OPEN S/W 1 SCREW Ô ASS'Y - MOTOR LOAD Fig. 5-10 Chassis-Main Parts Removal Samsung Electronics 5-10...
Page 44
All manuals and user guides at all-guides.com Disassembly and Reaasembly 5-4-4 Ass’y-Brkt Deck Removal 1) Remove 4 Screws Œ. 2) Lift up the Ass’y-Brkt Deck ´. Œ 4 SCREWS ´ ASS'Y - BRKT DECK Fig. 5-11 Ass’y-Brkt Deck Removal 5-11 Samsung Electronics...
Page 45
GEAR - FEED B Ô WASHER - PLAIN Ø ASS'Y - PICK UP Ú ASS'Y GEAR - FEED CU/CL ˇ SHAFT - P/U Ò WASHER - PLAIN ˆ RACK - SLIDE ¨ 2 SCREWS Fig. 5-12 Ass’y- Deck Parts Removal Samsung Electronics 5-12...
Input : Common power to transformer (Vp). Fig. 6-2 The output Vs of transformer is determined by the ratio of 1st Np and 2nd Ns. Vs = (Ns/Np) x Vp Fig. 6-3 Vout Vout is output (DC) by diode and condensor. Fig. 6-4 Samsung Electronics...
Page 47
I switch Fig. 6-6 Terms 1) 1st : Common power input to 1st winding. 2) 2nd : Circuit followings output winding of transformer. 3) f (Frequency) : Switching frequency (T : Switching cycle) 4) Duty : (Ton/T) x 100 Samsung Electronics...
Page 48
´ Rectify to PD12 and smooth to PE6. ˇ Use the output of transformer as PIC1 Vcc : The loads are different before and after PIC1 driving. (Vcc of PIC1 decreases below OFF voltage, using only the resistance due to load increase after PIC1 driving.) Samsung Electronics...
Page 49
Reverse sequence of the above description --> Duty down --> Vout down --> Maintain 5.8V (i.e., the feedback to maintains 5.8V). Œ PR35, PR36 : Reduce 5.8V overshoot ´ PR37, PC44 : Prevent PIC3 oscillation(for phase correction) ˇ PC09 : Adjust feedback response rate Samsung Electronics...
Page 50
6-1-3 (b) PIC1 (STR-G6153T) Internal Block Diagram V c c Voltage Sync. 6.3V UVLO Ref. OSC. Drain Feedback 2.5R Source Voffset Sense Rsense Reset Sense Sense 7.5V Reset Thermal Protection Control IC Control IC O C P Fig. 6-10 Samsung Electronics...
Page 51
RF SUM & AGC. It controls RF SUM & AGC gain by means of Pin 89-95 and interfaces with PWM signal, (output from PWM terminal of KS1453, via low-pass filter to adjust boost gain and peak frequency. EQout terminal is connected with EQin (Pin 86). Samsung Electronics...
Page 52
Œ EQG (Pin 97) : Changes the gain of peak frequency with EQ frequency characteristic. Convert PWM signal, output from KS1453, into DC via low-pass filter. ´ EQF (Pin 98) : Changes the peak frequency with EQ frequency characteristic. Convert PWM signal, output from KS1453, into DVD via low-pass filter. Samsung Electronics...
Page 53
CS4926 KS1461 KS1452 KS1453 ZIVA-3 SAA7128 FIC1 MIC1 MIC2 FRONT MICOM MAIN MICOM ADDR LATCH LC86P6232 TMP93CM41F 74AC573 MIC7 ADDR DECODER DATA BUS 74HC00 MIC5 MIC8 EEPROM EPROM KS24C020 AT27C080 MICOM BLOCK LOW ADDRESS HIGH ADDRESS Fig. 6-13 Samsung Electronics...
Page 57
Meanwhile, DVD repeats the track jump from 1 to 4 in inner direction at normal play (because data- read speed from disc is faster than data output speed on screen). ´ For CD, VCD Receive the signal output through E, F of Pick-up, from RIC1. The tracking error signal is similar to DVD. 6-12 Samsung Electronics...
Page 58
If the existing track count is within fine seek range, tracking begins using fine seek. 4) CLV SERVO(DISC MOTOR CONTROL SERVO) Input RF signal (from Pick-up) to SIC1 pin59. Detect SYNC signal from RF in SIC1, and output PWM signal to SIC1 pin 55 for constant linear velocity. Samsung Electronics 6-13...
Page 60
It measures the timing that data processed in DIC1 at DVD playback. STROBE DACK SDATA all Fig. 6-20 • CH1 : STROBE (DIC1-69, CLOCK) • CH2 : REQ (DIC1-70, DATA REQUEST) • CH3 : DACK (DIC1-58, DATA ACKNOWLEDGE) • CH4 : SDATA (DIC1-60~67, DATA) Samsung Electronics 6-15...
Page 61
AUX CVBS IN 4052 (Main Board) (AV Board) CVBS-1 Video VIC1 CVBS-2 data TIC2 A/V Decoder Amplifier ZiVA-3 BA7660 TIC1 SAA7128 Video encoder TIC3 MIC1 Amplifier Main Micom BA7660 TMP93CM41F EUROPE SCART JACK Fig. 6-21 Video Output Block Diagram 6-16 Samsung Electronics...
Page 62
Resistance (TR201 ~ TR206, TR303 ~ TR308) which is inserted to input terminal is bias resistance for input offset. The signal to which gain is adjusted by amplifier is outputted from jack via 75ohm. Samsung Electronics 6-17...
Page 63
DOLBY PRO-LOGIC / NATURAL / CONCERT / STADIUM are applied according to the users selection. The processed data(AIC1-39,40,41)is then sent to the CS4226(AIC3 : CODEC), where the CS4226(AIC3 : CODEC) D/A Converts to output Analog signals (AIC3 - pin 21, 22, 23, 24, 25, 26). 6-18 Samsung Electronics...
Page 64
When DC is occurred from the output of the I200 or I800, the Q413 TR connected to each channels is operated to activate the AMP_DET signal to the Micom when the collector voltage turn 5V into “Low”, which enables the Micom to operate the TR of Q251, Q551, and Q851, open the Relay. Samsung Electronics 6-19...
Page 65
All manuals and user guides at all-guides.com Circuit Descriptions MEMO 6-20 Samsung Electronics...
Page 79
All manuals and user guides at all-guides.com Exploded Views and Parts List 8-2 Deck Assembly S.N.A. S.N.A. S.N.A. S.N.A. : Service Not Available Samsung Electronics...
All manuals and user guides at all-guides.com 9. Electrical Parts List Loc.No Part No Description ; Specification Remark Loc.No Part No Description ; Specification Remark AH92-00635A ASSY PCB-MAIN;DVD-A500/XEF,MAIN DRR12 2007-000087 R-CHIP;6.8Kohm,5%,1/16W,DA,TP,1608 2007-000074 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 DRR13 2007-000092 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 2007-000074 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 DRR14 2007-000070 R-CHIP;0ohm,5%,1/16W,DA,TP,1608...
Page 86
All manuals and user guides at all-guides.com Electrical Parts List Loc.No Part No Description ; Specification Remark Loc.No Part No Description ; Specification Remark VR51 2007-000074 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 AH92-00534A ASSY PCB-JACK;DVD-A500,JACK VR52 2007-000074 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 AH63-00105A GROUND-REAR;-,PBS,T0.2,-,DVS3000 VR54 2007-000074 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 AC014 2203-000189 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, VR55 2007-000074 R-CHIP;100ohm,5%,1/16W,DA,TP,1608...
Digital Servo Analog Switch TV/AUX CVBS INPUT DECODER CVBS OUTPUT AC3 & TIC1 VIDEO MPEG5.1 HSYNC (SAA7128) Y/C OUTPUT (S-VIDEO) OUTPUT VSYNC Video Encoder TIC2 (BA7660) Pr/R Video AMP Pb/B TIC3 (BA7660) Video AMP EUROPE SCART JACK Samsung Electronics 10-1...
Page 97
All manuals and user guides at all-guides.com Block Diagram MEMO 10-2 Samsung Electronics...