EINHELL TC-SM 2131/2 Dual Original Operating Instructions page 12

wait until the blade has come to a stand-
still before you remove the piece which
has been cut off . It is extremely dangerous
to reach with your hand into the area anywhe-
re near the blade while it is slowing down.
s) Hold the handle very fi rmly if you want
to make an incomplete cut or if you re-
lease the switch before the saw head has
reached its bottom position. The braking
eff ect of the saw could cause the saw head to
be pulled down with a jerk, leading to a risk of
injury.
Additional safety precautions:
•
Use saw blades which are designed for
the purpose and for the material being
cut.
•
Use only blades which are recommended
by the manufacturer and comply with EN
847-1.
•
Use only blades with diameters, hole dia-
meters and tooth pitches which conform
with the technical data set out in the ori-
ginal operating instructions.
•
Use only blades with rotating speeds
shown on the blade which are equal to or
higher than the rotating speed shown on
the power tool.
•
Do not use saw blades that are blunt,
bent or damaged.
•
Check the direction of rotation whenever
you change the saw blade. There are ar-
rows marked on the machine and saw blade
to show the direction of rotation. They must
match.
•
Wear gloves to avoid getting cut when
you transport and change the saw bla-
des. Whenever practicable, saw blades must
be carried in a container.
•
Before use, check that the safety guard
for the saw blade is in proper working
order. If it does not close automatically or
is damaged, do not use the equipment any
more. In this case, contact the manufacturer
or an authorized customer service outlet to
get it professionally repaired.
•
If a switch is damaged or defective, arran-
ge for it to be replaced by the manufac-
turer or an authorized customer service
outlet.
•
Replace worn or damaged table inserts
in the saw table with a replacement part,
or arrange for them to be replaced by the
manufacturer or an authorized customer
service outlet.
Anl_TC_SM_2131_2_Dual_EX_UKCA.indb 12 Anl_TC_SM_2131_2_Dual_EX_UKCA.indb 12
GB
•
Only allow repairs to the equipment to
be carried out by the manufacturer or an
authorized customer service outlet using
original parts, otherwise the user may
suffer an accident.
•
Connect a dust extractor to the extractor
adapter on the machine.
•
Make sure that there is adequate stabi-
lity by always securing the machine to a
workbench or a table. Use the holes in the
machine's base frame to secure the machine.
Bolt the base frame to a workbench or a table.
•
Secure long workpieces against falling
off, e.g. using standard roller stands.
•
The extensions to the workpiece support
must be fastened and used at all times
while work is in progress
•
The machine is designed for cutting
wood and wood-type materials. To prevent
the saw blade overheating, perform cuts
quickly using blades that are properly shar-
pened.
•
Do not use the saw to cut fire wood.
•
The clamping device for securing the
workpiece must be used at all times. Do
not cut workpieces which are too small to
clamp securely with the clamping device.
•
Transport the machine by the carry hand-
les and the machine's base frame only.
•
If the machine is equipped with a laser,
this laser may not be replaced by a diffe-
rent type of laser. Repairs to the laser are
only allowed to be carried out by the manu-
facturer or an authorized customer service
outlet.
•
The saw blade must be stationary whe-
never you carry out any tidying up or
cleaning work. Do not remove any cutting
residues or other parts of workpieces from
the cutting zone while the machine is running
and the saw unit is not at rest (at the top).
•
If you need to use an extension cable,
use one with a minimum cross-section
of 1.5 mm² to ensure that the machine is
supplied with power.
•
If you use a cable reel, the complete
cable must be pulled off the reel.
•
Keep children and other people away
from the equipment. When not in use, stow
the equipment in a location that is out of
reach of children and unauthorized users.
•
Pull out the power plug (or take out the
rechargeable battery) and check that the
blade does not touch the table or workpi-
ece stop in any cutting position.
- 12 -
30.09.2021 08:28:35 30.09.2021 08:28:35