Table of Contents
Advertisement
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
8.1 Cleaning the spraying unit
Important! Risk of damage!
Dried-up spray material can clog the spraying unit,
making it useless for the next spraying job.
•
The spraying unit must be cleaned each time
after use before the spray material has time
to dry.
8.2 Cleaning the paint tub, the intake tube
and the ventilation tube
1. Remove the mains plug from the power so-
cket before beginning with any cleaning.
2. If applicable, remove the spraying unit (9/11)
from the motor unit (2) as described in the
section "Attaching/replacing the spraying unit".
3. Unscrew the paint tub (8) from the spraying
unit (see Fig. A and K).
4. Return the remaining material to the material
tin or dispose of it in accordance with the re-
gulations.
5. Pull the intake tube (25) and the ventilation
tube (24) downwards out of their catches on
the spraying unit. Take care to pull out the
whole multi-part ventilation tube (in one pie-
ce).
6. Use a cloth to remove any coarse dirt and
paint residues from out of the paint tub.
7. Use the cleaning brush to remove coarse dirt
or blockages from the inside of the intake tube
and the ventilation tube as well as from the
mountings on the spraying unit.
8. Re-insert the intake tube and ventilation tube
into the corresponding mounts on the spray-
ing unit from underneath. Make sure that the
intake tube is correctly aligned when you do
so: The hook at the top end of the intake tube
must run inside the guide groove on the corre-
sponding mount in order for the intake tube to
be correctly seated.
9. Fill solvent or water into the paint tub.
10. Screw the paint tub back onto the spraying
unit from underneath.
Anl_BT_FSS_500_EX_UK.indb 14
Anl_BT_FSS_500_EX_UK.indb 14
GB
11. Fit the spraying unit back on the motor unit as
described in the section "Attaching/replacing
the spraying unit".
12. Insert the power plug into a properly installed
socket outlet.
13. Press the trigger (6) and spray the solvent or
water into a container or cloth.
14. Keep repeating until only clear solvent or wa-
ter comes out.
15. Pull the power plug out of the socket outlet.
16. Empty the paint tub completely.
17. Keep the tub seal (27) free of material and
check it for damage.
18. Use a rag soaked in solvent or water to clean
the outside and the inside of the spraying unit
and the paint tub.
19. Allow all parts to become fully dry.
8.3 Cleaning the nozzle
1. Unscrew the union nut (4) or the union nut
(12) with adjusting ring from the respective
spraying unit (9/11) (see Fig. A and E).
2. Remove in forwards direction the air cap (19),
the nozzle (20) with nozzle seal (21), and the
twist cap (22) from the spaying unit. When do-
ing so, make sure that the lever (5) for setting
the spray width is in position on the twist cap
so that you can pull the twist cap off the spray-
ing unit.
3. Guide the tool (14) for removing the needle as
far as possible over the needle from the front.
Make sure that the hooks on the side of the
needle slide into the guide grooves inside the
tool.
4. Rotate the tool one quarter of a revolution
(90°).
5. With the help of the tool, pull the needle for-
wards out of the catch in the spraying unit.
6. Rotate the tool one quarter of a revolution
(90°) in order to remove the tool from the
needle. Make sure that the hooks on the side
of the needle run in the guide grooves inside
the tool. It must be possible to remove the tool
without you feeling any resistance.
7. Clean the air cap and the nozzle with a bristle
brush and solvent or water. Use the cleaning
needle (16) to clean any clogged openings.
8. Clean the needle thoroughly with a lint-free
cloth and solvent or water.
9. Check the nozzle seal for damage.
10. Allow all parts to become fully dry.
11. Re-insert the needle into the mount inside the
spraying unit. When doing so, make sure that
the needle is correctly aligned for the side
grooves at the end of the needle to engage
- 14 -
05.10.2021 12:45:33
05.10.2021 12:45:33
Advertisement
Table of Contents
