URC LT-3200 Quick Start Manual
  1. Manuals
  2. Brands
  3. URC Manuals
  4. Switch
  5. LT-3200
  6. Quick start manual

URC LT-3200 Quick Start Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
LT-3200 Switch
Thank you for purchasing the URC LT-3200 Switch!
This quick setup manual will help you plan and install your
Z-Wave™
lighting
solution. This product can be operated in any Z-Wave network with other
Z-Wave certified devices from other manufacturers. All mains operated nodes
within the network will act as repeaters regardless of vendor to increase reliability
of the network.
Specifications
Power:
120V AC / 60Hz
Signal (Frequency):
908.42 MHz
Operating Temperature Range:
32-104 °F (0-40 °C)
Maximum Load:
600W Incandescent / 300W LED / 150 CFL
Approval:
UL Listed / FCC / IC / Z-Wave
Plus™
Certified / CAN ICES-003 (B) / MB-003(B)
For indoor use. Specifications subject to
change without notice due to continuing
product improvement.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LT-3200 and is the answer not in the manual?

Questions and answers

Related Manuals for URC LT-3200

Summary of Contents for URC LT-3200

  • Page 1 LT-3200 Switch Thank you for purchasing the URC LT-3200 Switch! This quick setup manual will help you plan and install your Z-Wave™ lighting solution. This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All mains operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
  • Page 2 LT-3200 Switch Z-Wave Network Z-Wave can be used with a few devices or it can be used to build a large network. Below you’ll see two examples. In the first example, a user has a Gateway which is looking for Z-Wave devices within its radius. Z-Wave devices outside this radius will not be found and need to either be moved within the radius or use a repeating device to reach it.

  • Page 3: Material Thickness

    LT-3200 Switch Signal Material Thickness Depreciation Aerated Concrete < 30cm // Stone 11.8” < 1mm // Aluminum Coating 100% 0.04” < 30cm // Ceiling 11.8” Furniture < 30cm // 40-60% [Non-wood] 11.8” Glass < 5cm // 2.0” [No Metal Coating] <...

  • Page 4: Other Warnings

    Contrairement au LT-3200 Switch, les languettes du dissipateur de chaleur ne sont pas utilisées et n'ont aucun effet sur les performances. PLEASE NOTE: URC is unable to provide electrical and/or wiring advice outside of this document. If you are unable or unsure, please contact an electrician.
  • Page 5 Wiring Instructions: Neutral Installation Please use this if you have a neutral wire, typically white, in the installation area. For use of traveler terminals with the LT-3200, more wiring diagrams and information are available within the product manual found at: https://urcportal.com/ resources-total-control/ Single-Pole Installation (Single Switch) •...
  • Page 6 LT-3200 Switch LT-3200 Switch A. Config Button: This button is used to enter the configuration menu on your switch. When you hold it down for 10-15 seconds, the LED Bar (B) will light up Yellow to indicate you are in config mode. It can also be used to trigger a favorite scene.
  • Page 7 LT-3200 Switch Security 2 DSK The DSK can be found on the front of the switch (metal plate) and inside the box. Switch Configuration Settings There are a couple of ways to configure a switch. The first is via the switch itself, while the second is via the programming software.

  • Page 8: Switch Parameters

    LT-3200 Switch Switch Parameters Parameter Change at the Size About Description Range Default Switch? (Bytes) Default power state the switch will revert to after power loss. (0 - Return Power On State 0,1,2 to State | 1 - On | 2 - Off) Invert Switch Inverts the switch.

  • Page 9: Association Groups

    LT-3200 Switch Association Groups Group 1: Lifeline Members of this group will receive unsolicited messages related to the status of the switch. Group 2: Basic Setup Sends start and stop level change to associated devices. Grouping Identifier Send Commands Nodes...

  • Page 10: Warranty

    It is likely that such data, software, or other materials will be lost during service and URC will not be responsible for any such damage or loss. A dated purchase receipt, bill of sale, installation contract or other verifiable proof of purchase is required.For detailed information regarding...

Table of Contents