Advertisement
Quick Links
ROCKBRIDGE 3PC ALL WEATHER WICKER GLIDER SET
ASSEMBLY INSTRUCTIONS
ITEM# : GBO22-002 / GBO22-002NAVY / GBO22-002-B
SKU# : 810544190 / 810555286 / 810555289
Need help? We are here for you! 1-888-733-8169 Toll Free
Or email us at customerservice_01@yeah.net,customerservice_02@yeah.net
customerservice_03@yeah.net
Advertisement
Related Manuals for real living GBO22-002
Summary of Contents for real living GBO22-002
- Page 1 ROCKBRIDGE 3PC ALL WEATHER WICKER GLIDER SET ASSEMBLY INSTRUCTIONS ITEM# : GBO22-002 / GBO22-002NAVY / GBO22-002-B SKU# : 810544190 / 810555286 / 810555289 Need help? We are here for you! 1-888-733-8169 Toll Free Or email us at customerservice_01@yeah.net,customerservice_02@yeah.net customerservice_03@yeah.net...
-
Page 2: Maintenance
GENERAL BEST PRACTICES FOR ASSEMBLY: Read all instructions before starting Clear a flat covered space to begin assembly Always best to do it with a friend Note that hardware required is provided for every step Pay attention to orientation Number of the hardware corresponds to its letter in the package Helpful hints provided along the way WARNINGS: Use the correct screws as indicated. -
Page 3: Parts List
PARTS LIST 1PC Left Arm 1PC Right Arm 1PC Chair Back 1PC Seat Panel 1PC U-shaped Fitting 1PC Chair Base 1PC Seat Cushion 1PC Back Cushion HARDWARE LIST 4PC Spring Washer 18PC Washer 8PC Nut 4PC Screw(φ6x15mm) 14PC Screw(φ6x35mm) 1PC Allen Wrench 1PC Open End Wrench STEP 1 Assemble chair back (B) to left arm (A1) by inserting the steel pins. - Page 4 STEP 2 Assemble chair back (B) to left arm (A2) by inserting the steel pins. Then secure with 2 screws (I) and 2 washers (G) by using allen wrench (K). Do not fully tighten all screws now. insert steel pin insert steel pin STEP 3 Secure seat panel (C) to assembled left arm and right arms (A1.A2) with 4 screws (J) and 4 washers (G) by using allen wrench (K).
- Page 5 STEP 5 Turn over the assembled chair bucket and secure the swing arms on U-shaped fitting (D) to the bottom tube of left arm (A1) and right arm (A2) with 4 screws (J), and 4 nuts (H) with allen wrench (K) and wrench (L).
-
Page 6: Special Warning
STEP 7 Put seat cushion (M) and back cushion (N) on the chair. The chair is assembled. SPECIAL WARNING: THIS CHAIR IS NOT A TOY. DON'T OVER-SWING THE CHAIR. OVER- SWING THE CHAIR MAYBE MAKE THE CHAIR TIP OVER AND RESULT IN INJURY. -
Page 7: Hardware List
PARTS LIST 4PC Table Leg 1PC Table Top 1PC Table Tray HARDWARE LIST 12PC Washer 12PC Screw(φ6x12mm) 1PC Allen Wrench STEP 1 Secure 4 table legs (O) to table top (P) by using 8 screws (S) and 8 washers (R) with allen wrench (K). Do not fully tighten all screws now. - Page 8 STEP 2 Secure table tray (Q) to 4 table legs (O) by using 4 screws (S) and 4 washers (R) with allen wrench (K). Do not fully tighten all screws now. S R K STEP 3 Turn over the assembled table. Verify the alignment and adjust, fully tighten all screws.