Advertisement
Quick Links
Rotary Cutter
SC2560 & SC2572 Skid Steer
37920
Table of Contents
!
Read the Operator's Manual entirely. When you see this symbol,
the subsequent instructions and warnings are serious - follow
without exception. Your life and the lives of others depend on it!
Cover photo may show optional equipment not supplied
with standard unit.
For an Operator's Manual and Decal Kit in French
Language, please see your Land Pride dealer.
326-836M
Operator's Manual
Printed 1/15/21
Advertisement
Related Manuals for Land Pride SC2560
Summary of Contents for Land Pride SC2560
- Page 1 Your life and the lives of others depend on it! Cover photo may show optional equipment not supplied with standard unit. For an Operator’s Manual and Decal Kit in French Language, please see your Land Pride dealer. Printed 1/15/21...
- Page 2 Machine Height Machine Length Machine Width Machine Weight Delivery Date First Operation Accessories Dealer Contact Information Name: Street: City/State: Telephone: Email: California Proposition 65 WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 3 Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
- Page 4 App on your smart phone, open the App, Refer to Parts Manual QR point your phone on the QR code and Locator on this page for take a picture. detailed instructions. SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 5 Important Safety Information Important Safety Information Listed below are common practices that may or may not be applicable to the products described in this manual. Safety at All Times Look for the Safety Alert Symbol Careful operation is your best The SAFETY ALERT SYMBOL indicates there is a assurance against an accident.
- Page 6 Replace parts on this attachment correct tools and equipment. follow all shutdown procedures with genuine Land Pride parts only. Always properly match the wheel before leaving the operator’s seat to Do not alter this attachment in a way size to the properly sized tire.
- Page 7 Use Seat Belt and ROPS Keep Riders Off Lights and Devices Machinery Land Pride recommends the use of a CAB or roll-over-protective- Slow moving tractors, skid steers, Never carry riders on the power structures (ROPS) and seat belt and self-propelled machines can machine or attachment.
- Page 8 Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Avoid crystalline Silica Be aware of and follow OSHA If possible, change into disposable (or other local, State, or Federal) or washable work clothes at the (quartz) Dust guidelines for exposure to airborne...
- Page 9 Important Safety Information This page left blank intentionally. 1/15/21...
- Page 10 Spray soapy water onto the cleaned area. all damaged or missing labels. Order new labels from your Peel backing from label and press label firmly onto the nearest Land Pride dealer. To find your nearest dealer, surface. visit our dealer locator at www.landpride.com.
- Page 11 Danger: Keep Hands & Feet Away Danger: Thrown Object Hazard Danger: Rotating Blade Hazard Warning: General Safety Notice: Read Manual - Observe Safety Messages 37920 37920 Model SC2560 37939 818-831C Warning: High Pressure Model SC2572 1/15/21 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M...
- Page 12 Table of Contents Important Safety Information 37922 818-798C 37922 Warning: Pinch Point Hazard 3-Places 37939 818-552C Danger: Rotating Driveline (SC2572 Only) SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 13 Table of Contents Important Safety Information 37939 818-543C Danger: Guard Missing (SC2572 Only) 1/15/21 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M...
- Page 14 SC2560 and SC2572 highly number and serial number when ordering parts and in all versatile and easy to use. The SC2560 is compatible with correspondences with your Land Pride dealer. Refer to Skid Steers having 1500 psi to 3500 psi operating Figure 1 for location of your serial number plate.
- Page 15 “Additional Torque Values” at bottom of chart for with a protective door shield. A universal Operator exceptions to standard torque values. Protective Door is available from Land Pride or use a protective door provided by the Skid Steer Pre-Assembly Checklist manufacturer.
- Page 16 1/2"-13 x 2 1/4" lg. GR 5 hex head bolts (#1), and 1/2"-13 hex flange lock nuts (#2). Tighten nuts to the correct torque. See “Torque Values Chart for Common Bolt Sizes” on page 37. SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 17 Common Bolt Sizes” on page 37. Reattach coupling guard (#6) with 5/16" spring lock washers (#8) and 5/16"-18 x 3/4" GR5 hex head cap screws (#7). Tighten nuts to correct torque. 1/15/21 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M...
- Page 18 37384 Two high pressure hydraulic outlets are required for the hydraulic motor and one outlet for the case drain. Hose Route For Kubota CTL or SSL Machine (CTL Shown) Figure 1-6 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 19 (#10). Secure gauge wheel with bolts (#3). Tap punch in with a hammer until 3/8" x 2 1/2" lg. roll pin (#13). secure. Do not remove punch at this time. 1/15/21 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M...
- Page 20 (#2), flat washers (#5), -16X1 1/4" GR5 lock washers (#4), and 3/8" lock nuts (#3). Torque lock nuts (#3) to 31 ft. lbs. 4. Raise cutter up and remove support blocks. SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 21 (#1) as shown. Tighten nuts to correct torque. If Needed, Locate & Cut Notch in Door To Clear Skid Steer Skid Steer Frame. Hand Hold 24608 Operator Protective Door Figure 1-9 1/15/21 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M...
- Page 22 (B1) with chain pins (#5). 6. Insert cotter pins (#2) through chain pin holes and bend one or both legs of each cotter pin to secure them in place. 37928 Hitch Offset Figure 2-1 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 23 2" x 3" hitch tube to the Skid Steer lower hitch loop. Thread chain through the hitch loop and back towards the hitch plate. Connect quick link coupler to a chain loop as shown. 1/15/21 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M...
- Page 24 Skid Shoe the front deck corner. front leading cutting blade to at the front deck corner to ground level. ground level. 37997 Nominal Cutting Height Figure 2-4 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 25 Skid Shoe the front deck corner. cutting blade to ground level. at the front deck corner to ground level. Nominal Cutting Height Figure 2-5 1/15/21 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M...
- Page 26 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 27 Secure Skid Steer loader and attachment using tie-downs and chains. Refer to Figure 3-2: NEVER EXCEED 70 DEGREES OF OPERATING MOTION OR DAMAGE CAN OCCUR TO Cutting Instructions HITCH AND DECK. 1/15/21 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M...
- Page 28 Table of Contents Section 3: Operating Procedures General Operating Instructions Land Pride does offer a protective door with the SC2560 and SC2572 if one is not provided by your Skid Steer It is absolutely essential that you read and understand supplier.
- Page 29 Assuming all systems with the Skid Steer are “go” and outside of the cutter deck housing resulting in serious fully functioning, it is time to connect to the SC2560 or injury or death. Always inspect the area before you mow.
- Page 30 22-27 GPM Motor Assy ....326-015A SC2560 Hose Assy ....326-466L SC2572 Hose Assy .
- Page 31 Operator Protective Door Refer to Figure 4-5: Land Pride’s Protective Door Kit ..326-024A The Skid Steer MUST be equipped with an Operator Protective Door for shielding against flying debris when attached to a Rotary Cutter.
- Page 32 The parts on your cutter have been specially designed and should only be replaced with genuine Land Pride 4. Refer to Figure 5-2: Rotate blade bolt (#1) until in parts. Do not alter the cutter in a way which will adversely alignment with access hole.
- Page 33 802-277C BLADE BOLT 1 1/8-12 x 3 7/16 WITH KEY Steer in park, set park brakes, shut the Skid Steer off 820-112C SC2560 CUTTER BLADE 1/2 x 4 x 25 CW and remove switch key. 820-249C SC2572 CUTTER BLADE 1/2 x 4 x 29 CW 316-124H WELDMENT DISHPAN SC2560 3.
- Page 34 4. Repaint parts where paint is worn or scratched to treated by a doctor familiar with this type of injury within a prevent rust. Ask your Land Pride dealer for aerosol few hours or gangrene may result. DO NOT DELAY.
- Page 35 Gauge Wheel Spindle 1 - Zerk Type of Lubrication: Multi-purpose Grease Quantity = As required 24549 Hours Axle Hub Bearing 1 - Zerk Type of Lubrication: Multi-purpose Grease Quantity = As required 24549 1/15/21 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M...
- Page 36 (#2) and vented dipstick (#1). Land Pride dealer. Please see your Land Pride dealer if vented dipstick was not included. Type of Lubrication: 80-90W EP Gear Lube...
- Page 37 Double row chain guard. Deck lift height protection Safe chain limiter. Operator protection (Optional) Protective door shield. Cutting height gauging (Optional) Pivoting and adjustable front mounted gauge wheel with laminated tire. 1/15/21 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M...
- Page 38 Table of Contents Section 6: Specifications & Capacities 37931 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 39 SC25 Series (Skid Steer) Features Benefits Customer can choose one of three optional motors for the SC2560 cutter or one of Low volume motor @ 11-16 gpm two optional motors (medium and high volume) for the SC2572 cutter. This allows Medium volume motor @ 17-21 gpm the cutter to fit a wide variety of Skid Steers.
- Page 40 Blade carrier bent. Replace blade carrier. Do not tilt the hitch plate too far forward. Hitch lugs failing Tilting hitch plate too far forward. Do not put down pressure on hitch plate SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 41 Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above. Additional Torque Values Wheel Hub Stub 1/2"-20x1 5/8Gr 5 85 ft-lbs. Blade Bolt Lock Nut 450 ft-lbs Blade Carrier Hub Nut 450 ft-lbs 1/15/21 SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M...
- Page 42 Table of Contents Section 9: Torque Values Chart This page left blank intentionally. SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M 1/15/21...
- Page 43 This Warranty is limited to the repair or replacement of any defective part by Land Pride and the installation by the dealer of any such replacement part, and does not cover common wear items. Land Pride reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship.
- Page 44 Corporate Office: P.O. Box 5060 Salina, Kansas 67402-5060 USA www.landpride.com...