1. Manuals
  2. Brands
  3. LEAP Electronics Manuals
  4. Computer Hardware
  5. LEAPER-56
  6. User manual

LEAP Electronics LEAPER-56 User Manual

Universal ic writer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
LEAPER-56
Universal IC Writer
User's Manual

Advertisement

Table of Contents
loading

Summary of Contents for LEAP Electronics LEAPER-56

  • Page 1 LEAPER-56 Universal IC Writer User's Manual...

  • Page 3: Table Of Contents

    Universal IC Writer User's Manual Contents Chapter 1 Product Description ........1-1 Introduction 1-2 Safety Information 1-3 Precautions 1-4 Operating System, Hardware Requirement 1-5 Accessories Chapter 2 Product Installation ........2-1 Hardware Installation 2-2 Software Installation 2-3 Driver Installation Chapter 3 IC Insertion ............
  • Page 4 Universal IC Writer User's Manual Contents 4-6 Save 4-6-1 Save File Path 4-6-2 Save File Format 4-6-3 Main Range Select Saving 4-7 Device Processing Procedure 4-7-1 Read 4-7-2 Data Confirm 4-7-3 Erase 4-7-4 Blank Check 4-7-5 Program 4-7-6 Verify 4-7-7 Protect 4-7-8 ALL RUN 4-7-9 Condition Display Chapter 5 Simple Operating Practice...

  • Page 5: Introduction

    Universal IC Writer User's Manual Chapter 1 Product Description 1-1 Introduction Due to the development of IC has been changed with each passing days. The memory capacity and operating frequency of IC has not been in support of traditional programmers. In order to shorten the waiting time of programming and let IC can be operated on accurate frequency, we takes ICT technology into the Universal Programmer.

  • Page 6: Precautions

    Universal IC Writer User's Manual 1-3 Precautions 1. When you deal with your IC through programmer, the programmer will access it on high frequency signal. For the quality and yield rate of the IC, you must note following: a.While the IC is in processing action (including read / verify / programming / erase / blank check ...

  • Page 7: Operating System, Hardware Requirement

    Universal IC Writer User's Manual 1-4 Operating System, Hardware Requirement Operating System ： Windows XP / Vista / Windows 7 (32bits / 64bits) CPU ： PC / Pentium IV or above Memory ： 1 GB RAM or above Hard disk space ： 500 MB or more (main program) Data buffer with 1GB or more (depending on device capacity) Monitor Resolution: 800 x 600 pixels or above...

  • Page 8: Chapter 2 Product Installation

    Universal IC Writer User's Manual Chapter 2 Product Installation 2-1 Hardware Installation 1. Using standard accessory with Y-USB cable and connecting two USB plugs to the computer. If you use the USB Hub, please connect it to the Power Adapter (5V), and remove other power consumption USB product on the Hub.

  • Page 9: Driver Installation

    Universal IC Writer User's Manual 2-3 Driver Installation 1.Please install the software on your computer. And then connecting the programmer to computer through the Y-USB cable. Starting driver installation. 2.For the first time when installing the hardware. There will be a message about finding a new device, and then asking install the driver.
  • Page 10 Universal IC Writer User's Manual 3.The path is set to "\ Universal IC Writer II \ USBDrv" list (The above options need to be checked.) Choose to continue the installation...
  • Page 11 Universal IC Writer User's Manual 4.After installation, you will see the the "Universal IC Writer II ” device at the path- "Control Panel \ System \ Hardware \ Device Manager". This means the machine had been set. Press [Finish] End of the installation...

  • Page 12: Chapter 3 Ic Insertion

    Universal IC Writer User's Manual Chapter 3 IC Insertion 3-1 General IC Insert (DIP package) If the IC such as DIP package, please insert devices align down the programmer's Socket. The first pin would be at the upper left position (IC gap towards the top) 3-2 Special IC Insert Via Adapter (Special package) When the IC is not the DIP package, please use appropriate adapters.

  • Page 13: Chapter 4 Software Operating

    Universal IC Writer User's Manual Chapter 4 Software Operating 4-1 Software Main Screen Below is the default interface when starting the software. If the user starts the program and never selects IC number for the first time. It will automatically enter the "Select Device"...

  • Page 14: Device Select/Project

    Universal IC Writer User's Manual 4-2 Device Select/Project 4-2-1Device Select Making Selection of IC serial number for programming. Then pressing the "OK", the driver and database of related IC will be sent to the programmer. Generally it need take 2~3 seconds to implement any action of programming. Search Brand LOGO Selection Report...

  • Page 15: Device Selected Record

    Universal IC Writer User's Manual 4-2-2 Device Selected Record The system will automatically record the selected serial number of IC from user(up to 20 records).In this field, the user can directly select the usual IC serial number. Note: The brand name and refer logo from software are the property of the related company.

  • Page 16: Project

    Universal IC Writer User's Manual 4-2-3 Project Project List Project Information 1. Create Create a new project. 2. Add Add a created project file to the project list. 3. Delete Delete the selected project from the project list. 4. Load Load the selected project from the project list.

  • Page 17: File Load

    Universal IC Writer User's Manual 4-3 File Load Load the file to the data buffer as the user-specified file and format. Browse Searching Records Automatically adjust to IC's capacity Fill the value of unset region of the data 4-3-1 Load File Path The path of programming, which can select the file downloaded or reselect by pressing "Browse"...

  • Page 18: Edit

    Universal IC Writer User's Manual 4-4 Edit 8 Bits display mode View mode, the information can not be modified 16 Bits display mode Edit Mode Current address Data (16 hex mode) Data (ASCII mode) 4-4-1 Display Mode (8 Bits/16 Bits) Switch the data format: Byte (8 Bits) or Word (16 Bits) 4-4-2 View/Edit Mode View mode is just for displaying the data, therefore the state can not be changed.

  • Page 19: Option Setting

    Universal IC Writer User's Manual 4-5 Option Setting This page is related setting for software and processing IC. The page will change the state immediately when clicking, without pressing any confirm key. 4-5-1 General System Setting 1. Insert Detect: Before every IC processing, the system will check whether the IC is wrong-side, offset, empty inserted,or bad connection.
  • Page 20 Universal IC Writer User's Manual 4-5-2 Device Check This page is about the related parameters setting of the IC. The type, quantity and form will be changed from different IC. All of the setting parameters are programed to IC when programming. However the protect-related setting is excluded, such as: Write Protect or Read Protect.

  • Page 21: Save

    Universal IC Writer User's Manual 4-6 Save Saving users' specified file in a variety formats from contents of the data buffer. File browsing (File could not exist.) Automatically setting to the capacity of IC 4-6-1 Save File Path and File name: The path of saving.

  • Page 22: Erase

    Universal IC Writer User's Manual 4-7-3 Erase Erase all the internal data of DUT IC to default setting(Including protection setting). Unless the user confirms the DUT IC is new or empty, we suggest adding this function when programming. Besides, some ICs' protect function is only for one time. It may cause unable to erase or re-program.

  • Page 23: Chapter 5 Simple Operating Practice

    Universal IC Writer User's Manual Chapter 5 Simple Operating Practice e.g.1.Programming the MCU from data of computer, and adding protection on IC. 1.Click button on the top left to enter "Device Select" page. Then input searching keywords "AT89C51", the "Manufacturer" column will list possible companies.
  • Page 24 Universal IC Writer User's Manual 3. Click the key on top left to enter the "Load File" page. Then clicking the button on the top right folder , selecting the file you need load. In this example the file format to be loaded is "intel HEX", you can set in "Format" column.
  • Page 25 Universal IC Writer User's Manual 5.Put the IC on the programmer's socket. The IC's gap is upward. The bottom of the IC aligns with the bottom of the socket. Confirm the IC is placed , then put the socket's stick down. The IC will be steadily fixed. 6.In this example, users need do Protect process to this IC.
  • Page 26 Universal IC Writer User's Manual 6.Back to the main menu, check the lower left button at "Procedure" column. Then checking other procedures according to your needs. 7.Finally confirming the IC is placed steadily again and checking the serial number. After "Check Sum" procedure is correct, then clicking button.
  • Page 27 Universal IC Writer User's Manual e.g.2.Reading internal memory data of the IC, and saving it by Binary Format. 1. Click the top left button to enter "Device Select" page. Enter searching word of the IC in "Search" column. Clicking the manufacturers and serial number of the IC.
  • Page 28 Universal IC Writer User's Manual 3. Back to the main window, clicking the left side keys in "Data/ Option" column. The programmer will start reading IC internal data and save it in the buffer of computers. After finishing "Read" process. If you have checked process, the programmer will implement “...
  • Page 29 Universal IC Writer User's Manual 5. Click top left button to enter " Save File" pages. Then clicking top right button. Selecting contents you want to save the file and clicking the file or typing a file name. Completed entering contents and name of the file, pressing the lower right button back to "Save File"...
  • Page 30 Universal IC Writer User's Manual 3. You can scroll to check or click button. Let message convert to text file.
  • Page 31 Universal IC Writer User's Manual e.g.4. Create a new project 1. Follow the step 1~4 of e.q.1. 2. Click the top left button to enter "Project" page. 3. Click the bottom button to enter "Create Project Setting" page. 4. Fill the "Create Project Setting" page. The “Author”...

  • Page 32: Chapter 6 Troubleshooting

    Universal IC Writer User's Manual Chapter 6 Troubleshooting Status Description ： Software and driver can not be settled. The soft can not run or abnormally run. Troubleshooting ： Please use "Administrator" permission to log in and then run the driver's installation or software implementation. Status Description ：...
  • Page 33 Universal IC Writer User's Manual Status Description ： When software appears below warning message: It means the power supplied by USB port is not enough. Click "Cancel" can ignore that, but it may cause following procedure wrong. Troubleshooting ： 1. Use standard Y-USB cable and connected to the computer's two USB port.

Table of Contents